Direct printing of self-assembled lipid tubules on substrates

Lipid tubules formed by rolled-up bilayer sheets have shown promise in drug delivery systems, nanofluidics, and microelectronics. Here we report a method for directly printing lipid tubules on substrates. Preformed lipid tubules of 1,2-bis(tricosa-10,12-diynoyl)-sn-glycero-3-phosphocholine are aligned in the recessed channels of a thin poly(dimethylsiloxane) (PDMS) stamp. The aligned lipid tubules then serve as an "ink" for microcontact printing. We demonstrate that two-dimensional (2-D) arrays of aligned lipid tubules can be transferred onto planar, patterned, and curved substrates from the recessed channels of the PDMS stamp by bringing the tubule-inked PDMS stamp into contact with these substrates. We show that the 2-D array of aligned lipid tubules can be transcribed into a 2-D array of aligned silica cylinders through templated sol-gel condensation of tetraethoxysilane.     

Selective adsorption and alignment behaviors of double- and multiwalled carbon nanotubes on bare Au and SiO2 surfaces

We present the study of selective adsorption and alignment behaviors of double- and multiwalled carbon nanotubes (dwCNTs and mwCNTs) on self-assembled monolayer (SAM) patterns, bare Au, and SiO2 surfaces. dwCNTs and mwCNTs exhibited stronger affinity to polar SAMs, bare Au, and SiO2 surfaces than to nonpolar SAM surfaces. Furthermore, we found the adsorption probability of smaller carbon nanotubes (CNTs) was higher than that of larger CNTs. As proof of concept, we successfully assembled and aligned dwCNTs and mwCNTs on Au and SiO2 substrates without relying on external forces and demonstrated wafer-scale fabrication of back-gate transistors based on dwCNTs with a high yield.     

Zigzag lipid tubules

We report a method based on poly(dimethylsiloxane) (PDMS) stamp-assisted moving contact line to bend lipid tubules into zigzags on glass substrates. Atomic force microscopy (AFM) reveals that the zigzag lipid tubules buckle at the bent sites. The measurements of buckling heights as a function of bending angles suggest a gradual buckling mode. By imaging the zigzag tubules with AFM under different loading forces, we study the correlation between the loading force and the tubule compression. The reduced stiffness at the buckling sites of zigzag tubules suggests that lipid molecules are reorganized during the gradual buckling.     

Directing the growth of highly aligned gold nanorods through a surface chemical amidation reaction

This paper describes the seed-mediated growth of highly aligned gold nanorods (Au NRs) over large areas directly on a Si(100) surface. The Si(100) surface is NH2-functionalized with (aminopropyl)triethoxysilane (APTES) followed by a DCC-catalyzed surface amidation reaction with acetic acid. After exposure to a gold nanoparticle (Au NP) "seed" solution, chemical seed-mediated growth of the surface-bound seeds via reduction of AuCl4- by ascorbic acid in the presence of cetyltrimethylammonium bromide leads to the growth of highly aligned Au NRs on the surface. About 80% of the NRs are aligned in the same direction within a +/-30 degrees range. Au NRs account for 19% of the nanostructures with average aspect ratio (AR) of approximately 20. The alignment direction did not correlate with the atomic arrangement of the Si(100) crystal since it varied over different regions of the sample, rotating by 90 degrees from top to bottom of an approximately 5 mm sample. Si crystallinity may still be important since alignment is not observed on amorphous glass. Surface functionalization is the key since alignment is only observed following the amidation reaction and not on NH2-functionalized, SH-functionalized, or bare Si(100) surfaces. Alignment also occurred for Au NRs grown on Si(100)/APTES reacted with succinic acid and on Ag NRs grown on Si(100)/APTES/acetic acid surfaces. This unique alignment of metal NRs promoted by a surface amidation chemical reaction may find use in nanoelectronics, chemical sensing, and plasmonics applications.     

Two-dimensional ordered arrays of aligned lipid tubules on substrates with microfluidic networks

Microfluidic networks is a powerful tool for aligning one-dimensional materials over a large area on solid substrates. Here we show that lipid nano- and microtubules can be assembled into two-dimensional (2-D) parallel arrays with controlled separations by combining fluidic alignment with dewetting, which occurs within microchannels. We also demonstrate that lipid tubules can be bent into a well-defined shape at the entrance of the channels by the capillary force. Atomic force microscopy is used to study the structure and stability of the aligned lipid tubules on substrates. The deposition experiments with silica colloidal particles show that the 2-D parallel-aligned tubules can be used as a template to synthesize silica films with controlled morphologies and patterns on substrates in a single-step process.     

Patterning polymerized lipid vesicles with soft lithography

The applications of soft lithography in patterning polymerized lipid vesicles of 1,2-bis(tricosa-10,12-diynoyl)-sn-glycero-3-phosphocholine on glass substrates are reported. We demonstrate that the polymerized vesicles can be used as a high molecular weight ink to be transferred from a PDMS stamp onto a glass substrate to form two-dimensional stripes with a controlled separation. By combining channel flow with dewetting within microfluidic networks, we assemble the polymerized vesicle into three-dimensional stripes and one-dimension lines on glass substrates. Atomic force microscopy shows that these patterned vesicle structures are stable on glass substrates. The simple, stable, and precise immobilization of lipid vesicles on solid substrates will open up the possibility of integrating them in biosensors and microelectronic devices.     

Manipulation and organization of ferromagnetic nanowires by patterned nematic liquid crystals

We introduce a method to manipulate and organize ferromagnetic nanowires using the elastic forces imposed on nanowires suspended in nematic liquid crystals via patterned variations in the nematic director. As a test case for the technique, we investigate nematic environments consisting of stripes of alternating director orientations formed by lithographically patterned substrates. Nanowires oriented by small external magnetic fields are driven by the liquid crystal to specific locations of the pattern. The observed forces on the nanowires agree with calculations based on nematic elasticity.     

Bending and radial deformation of lipid tubules on self-assembled thiol monolayers

Lipid tubules represent a hollow, cylindrical supramolecular structure formed by rolled-up lipid bilayers. We find that the lipid tubules of 1,2-bis(tricosa-10,12-diynoyl)-sn-glycero-3-phosphocholine can be bent into a loopike shape by the shrinking contact line of droplets on self-assembled monolayers (SAMs) of 1-dodecanethiol. The persistence length of individual lipid tubules is estimated to be approximately 41 microm. The radial deformation of the lipid tubules on SAMs is studied under applied load using atomic force microscope. The stiffness of the tubules in the radial direction is found to increase when the number of the lipid bilayers in the tubule wall increases.     

Spatially selective guided growth of high-coverage arrays and random networks of single-walled carbon nanotubes and their integration into electronic devices

The chemical vapor deposition growth of unusual arrangements of single-walled carbon nanotubes (SWNTs) by the combined of use patterned catalysts and quartz substrates is reported. Nearly perfectly aligned, high-coverage arrays of SWNTs can be generated in this manner. High-coverage random networks of SWNTs can also be created in the same growth step, with good spatial alignment and electrical interfaces to the aligned arrays. Tubes with these geometries are ideally suited to applications in thin-film electronic devices. We demonstrate this possibility through the construction of thin-film-type transistors in which the random networks form the source and drain electrodes and the aligned arrays form the channel.     

Groove-spanning behavior of lipid membranes on microfabricated silicon substrates

We report on a spreading behavior of phospholipid membranes that arise from a lump of phospholipid (a lipid source) on topographically patterned substrates immersed in an aqueous solution. Microgrooves with well-defined shapes were prepared on Si111 surfaces by anisotropic etching in an alkaline solution. A spreading front that consists of membrane lobes and a single lipid bilayer was observed on the patterned silicon substrates by utilizing fluorescence interference contrast (FLIC) microscopy. FLIC images indicate that the membrane lobes span the microgrooves, while the underlying single lipid bilayer spread along the surface of the microgrooves. In fact, fluorescent polystyrene nanoparticles could be encapsulated in the microgrooves that were completely covered with the membrane lobes. The groove-spanning behavior of membrane lobes is discussed in terms of a balance between adhesion and bending energies of lipid bilayers.     

金纳米粒子与聚吡咯纳米管的复合及其SERS效应研究

通过柠檬酸盐与HAuCl4水溶液在微沸状态下反应制备的金纳米粒子因其特殊的表面与界面效应在光学、生物学和催化化学领域得到了广泛应用,而聚吡咯(PPy)具有环境稳定性好、电导率高且变化范围大、容易合成等优点,聚吡咯纳米管可用作导电材料、酶封装材料、抗静电材料,也可用于制备传感器、传动器、固体电解质电容器等。     

Control of particle alignment in water by an alternating electric field

We attempted to align a large number of silica particles dispersed in aqueous solution by controlling the alternating electric field between the two electrodes (400 microm apart). Relatively large particles (9.9 microm) were found to align forming strings in the direction parallel to the electric field while relatively small particles (2.0 and 4.9 microm) were observed to align making stripes in the direction perpendicular to the field. The number of stripes formed by particles between the electrodes increased with increasing frequency of the alternating field. This peculiar perpendicular particle alignment appeared when the contribution to particle alignment of electroosmotic flow exceeded that of dielectric polarization and the osmotic flow was found to be stronger around the particles than in the vicinity of the electrode surface.     

Nematic liquid crystal alignment on chemical patterns

Patterned Self-Assembled Monolayers (SAMs) promoting both homeotropic and planar degenerate alignment of 6CB and 9CB in their nematic phase were created using microcontact printing of functionalized organothiols on gold films. The effects of a range of different pattern geometries and sizes were investigated, including stripes, circles and checkerboards. Evanescent wave ellipsometry was used to study the orientation of the liquid crystal (LC) on these patterned surfaces during the isotropic-nematic phase transition. Pretransitional growth of a homeotropic layer was observed on 1 µm homeotropic aligning stripes, followed by a homeotropic monodomain state prior to the bulk phase transition. Accompanying Monte Carlo simulations of LCs aligned on nanoscale-patterned surfaces were also performed. These simulations also showed the presence of the homeotropic monodomain state prior to the transition.     

Shear-induced assembly of graphene oxide particles into stripes near surface

We report the shear-induced assembly of graphene oxide (GO) particles into periodic stripe-like patterns near the surface. These stripe-like patterns, which have an average periodic length of 100–250 μm, are aligned in a wavy manner along the normal to the flow direction. The self-assembled GO structures are investigated at different depths using three different analysis methods, namely, reflective microscopy observations of the photonic-crystalline GO dispersion, polarized optical microscopy, and fluorescence confocal laser scanning microscopy. The surface microstructures observed in reflection mode are different from the shear-induced band structures formed in bulk thermotropic liquid crystals and liquid crystal polymers, in terms of the shape and scale of the stripes. Further, there is also a difference in terms of the dependence of the stripe width on the shear rate. The observations suggest that the stripes are formed because of a competition between the stable surface-field-induced planar alignment of the GO particles near the surface and their relatively unstable shear-induced vertical alignment in the bulk. The findings of this study should advance our understanding of GO assembly under shear stress. Further, the proposed method is a novel one for inducing the assembly of GO particles into microstructures shaped as thread-like stripes.     

Director distribution in field-induced undulated structures of cholesteric liquid crystals

Structures with a periodic in-plane liquid crystal director field modulation induced by an electric field are studied in cholesteric liquid crystals (CLCs). A phenomenon of the electric-field-induced instability in a planarly aligned cholesteric cell is used to create these undulated structures. The initial field-off state is planarly aligned with the cholesteric helix axis oriented perpendicular to the cell substrates. The interaction of the CLC with an electric field results in modulation of the refractive index, which is visualised as stripe domains oriented either along or perpendicular to the rubbing direction at cell alignment surfaces. The threshold electric field for the undulation appearance and a period of stripes are measured experimentally for three Grandjean zones (ratio d/p ~ 0.5, 1.0, and 1.5, where d is a cell thickness and p is the natural cholesteric pitch). For the zone with d/p ~ 1.0 using numerical simulations, we describe in detail the director distribution at an applied electric field. It is found that the in-plane undulated structure is characterised by a conical director rotation on moving along the alignment direction. The conical axis is tilted with respect to the alignment axis. The sign of the tilt angle depends on the handedness of CLC.     

Anomalous uniform domain in a twisted nematic cell constructed from micropatterned surfaces

We have discovered an optically uniform type of domain that occurs in twisted nematic (TN) cells that are constructed from substrates chemically patterned with stripes via microcontact printing of self-assembled monolayers; such domains do not occur in TN cells constructed from uniform substrates. In such a cell, the azimuthal anchoring at the substrates is due to the elastic anisotropy of the liquid crystal rather than the conventional rubbing mechanism. A model is presented that predicts the relative stability of the twisted and anomalous states as a function of the material and design parameters.     

Molecular alignment in a liquid induced by a nonresonant laser field: Molecular dynamics simulation

We carried out molecular dynamics (MD) simulations for a dilute aqueous solution of pyrimidine in order to investigate the mechanisms of field-induced molecular alignment in a liquid phase. An anisotopically polarizable molecule can be aligned in a liquid phase by the interaction with a nonresonant intense laser field. We derived the effective forces induced by a nonresonant field on the basis of the concept of the average of the total potential over one optical cycle. The results of MD simulations show that a pyrimidine molecule is aligned in an aqueous solution by a linearly polarized field of light intensity I approximately 10(13) W/cm2 and wavelength lambda = 800 nm. The temporal behavior of field-induced alignment is adequately reproduced by the solution of the Fokker-Planck equation for a model system in which environmental fluctuations are represented by Gaussian white noise. From this analysis, we have revealed that the time required for alignment in a liquid phase is in the order of the reciprocals of rotational diffusion coefficients of a solute molecule. The degree of alignment is determined by the anisotropy of the polarizability of a molecule, light intensity, and temperature. We also discuss differences between the mechanisms of optical alignment in a gas phase and a liquid phase.     

Ordering rigid rod conjugated polymer molecules for high performance photoswitchers

Molecules of a rigid rod conjugated polymer, a derivative of poly(para-phenylene ethynylene)s with thioacetyl end groups (TA-PPE), were well aligned by drop-casting the polymer solution onto the friction-transferred poly(tetrafluoroethylene) substrates. TA-PPE molecules were found to be exactly oriented with their conjugated backbones along the PTFE sliding direction. Photoresponse characteristics based on the uniaxially ordered film were significantly improved compared to those of devices with the disordered film. For example, the switch on/off ratio of the photoswitchers with aligned molecules was as high as 330-400, while that of devices without alignment was only 8-12. It was due to the efficient carrier transport along the highly aligned polymer films, in which the molecules of TA-PPE oriented along the carrier transport direction of the devices.     

Soft-graphoepitaxy using nanoimprinted polyhedral oligomeric silsesquioxane substrates for the directed self-assembly of PS-b-PDMS

We report here the fabrication of periodic sub-25 nm diameter size cylinder structures using block copolymer (BCP) directed self-assembly on nanoimprinted topographically patterned substrates. Tailored polyhedral oligomeric silsesquioxanes (POSSs) films were spin coated onto silicon substrates and were patterned by nanoimprint lithography to produce topographies commensurable with the BCP domain spacing. The chemistry of the POSS was tuned to control the alignment and orientation of the BCP films. The substrates were used to direct the microphase separation (following toluene solvent annealing) of a hexagonal structure forming polystyrene-block-polydimethylsiloxane (PS-b-PDMS) having a domain spacing of 42.6 nm and PDMS cylinder widths of 23.7 nm. On more hydrophilic POSS substrates the cylinders were obtained parallel to the substrate plane and aligned with the topography. In contrast, in more hydrophobic POSS patterns, the cylinders align perpendicular to the substrate plane. The use of these methods for the nanofabrication of vias, nanofluidic devices or interconnect structures of sub-25 nm feature size is discussed.     

Lipid nanotubule fabrication by microfluidic tweezing

There is currently great interest in the development of lipid enclosed systems with complex geometrical arrangements that mimic cellular compartments. With biochemical functionalization, these soft matter devices can be used to probe deeper into life's transport dominated biochemical operations. In this paper, we present a novel tool for machining lipid nanotubules by microfluidic tweezing. A bilayer poly(dimethylsiloxane) (PDMS) device was designed with a lipid reservoir that was loaded by capillary action for lipid film deposition. The lipid reservoir is vertically separated from an upper flow for controlled material wetting and the formation of giant tubule bodies. Three fluidic paths are interfaced for introduction of the giant tubules into the high velocity center of a parabolic flow profile for exposure to hydrodynamic shear stresses. At local velocities approximating 2 mm s (-1), a 300-500 nm diameter jet of lipid material was tweezed from the giant tubule body and elongated with the flow. The high velocity flow provides uniform drag for the rapid and continuous fabrication of lipid nanotubules with tremendous axial ratios. Below a critical velocity, a remarkable shape transformation occurred and the projected lipid tubule grew until a constant 3.6 mum diameter tubule was attained. These lipid tubules could be wired for the construction of advanced lifelike bioreactor systems.