Sensitive electrochemical determination of Sudan II in food samples using a poly(aminosulfonic acid) modified glassy carbon electrode

In this paper, a novel poly(aminosulfonic acid) modified glassy carbon electrode (PASA/GCE) for the determination of Sudan II was fabricated through electrochemical polymerizat ion. The electrochemical behavior of Sudan II at the modified electrode was studied by cyclic voltammetry. Results show that the modified electrode exhibits excellent electrocatalytic activity toward the electrochemical redox reaction of Sudan II. Under optimal experimental conditions, the oxidation peak current is linearly proportional to the concentration of Sudan II in the ranges of 4.0 × 10^?8 to 1.0 × 10^?6 mol L^?1 and 1.0 × 10^?6 to 1.2 × 10^?5 mol L^?1. The linear regression equations are i _pa(A) = 2.87c + 3.74 × 10^?6, r = 0.9977 and i _pa(A) = 0.78c + 6.11 × 10^?6, r = 0.9982, respectively, and the detection limit is 4.0 × 10^?9 mol L^?1. The novel method shows good recovery, reproducibility and sensitivity for the voltammetric determination of Sudan II in food samples.     

The electrochemistry of uric acid at a gold electrode modified with L-cysteine, and its application to sensing uric urine

The electrochemistry of uric acid at a gold electrode modified with a self-assembled film of L-cysteine was studied by cyclic voltammetry and differential pulse voltammetry. Compared to the bare gold electrode, uric acid showed better electrochemical response in that the anodic peak current is stronger and the peak potential is negatively shifted by about 100 mV. The effects of experimental conditions on the oxidation of uric acid were tested and a calibration plot was established. The differential pulse response to uric acid is linear in the concentration range from 1.0?×?10^?6 to ~?1.0?×?10^?4 mol?L^?1 (r?=?0.9995) and from 1.0?×?10^?4 to ~?5.0?×?10^?4 mol?L^?1 (r?=?0.9990), the detection limit being 1.0?×?10^?7 mol?L^?1 (at S/N?=?3). The high sensitivity and good selectivity of the electrode was demonstrated by its practical application to the determination of uric acid in urine samples.

Sensitive and Selective Detection of Dopamine Using a DNA Immobilized Ethylenedidamine/Polyglutamic Modified Electrode

DNA was attached on the surface of an ethylenedidamine/polyglutamic(En/PGA) modified glassy carbon electrode (GCE) to create a novel voltammetric sensor (DNA/En/PGA/GCE) for dopamine (DA). This modified electrode exhibited a linear voltammetric response for DA in the range from 1.0×10^?7 mol L^?1 to 1×10^?5 mol L^?1, with a detection limit of 2×10^?8 mol L^?1. The detection of DA was found to be unaffected by the presence of ascorbic acid, uric acid, serotonin and folic acid. The method proposed was applied to detect DA in pharmaceutical dosage and human blood serum with good satisfactory results.     

Electrochemical determination of tryptophan based on silicon dioxide nanopartilces modified carbon paste electrode

Silicon dioxide nanoparticles modified carbon paste electrode was fabricated and used for electrochemical investigation of tryptophan. Compared with the unmodified electrode, the peak current significantly increased. Experimental conditions for tryptophan determination were optimized. Linear relationship between the peak current and tryptophan concentration was obtained in the range of 1.0 × 10^?7?5.0 × 10^?6 mol L^?1 and 5.0 × 10^?6?5.0 × 10^?5 mol L^?1 with an estimated detection limit of 3.6 × 10^?8 mol L^?1 (S/N = 3). Tryptophan in pharmaceutical and human serum samples were successfully determined by the proposed method.     

One-step construction of an electrode modified with electrodeposited Au/SiO2 nanoparticles, and its application to the determination of NADH and ethanol

A new electrode was developed by one-step potentiostatic electrodeposition (at ?2.0 V for 20 s) of Au/SiO₂ nanoparticles on a glassy carbon electrode. The resulting electrode (nano-Au/SiO₂/GCE) was characterized by scanning electronic microscopy, X-ray photoelectron spectroscopy and electrochemical techniques. The electrochemical behavior of dihydronicotinamide adenine dinucleotide (NADH) at the nano-Au/SiO₂/GCE were thoroughly investigated. Compared to the unmodified electrode, the overpotential decreased by about 300 mV, and the current response significantly increased. These changes indicated that the modified electrode showed excellent catalytic activity in the oxidation of NADH. A linear relationship was obtained in the NADH concentration range from 1.0?×?10^?6 to 1.0?×?10^?4 mol?L^?1. In addition, amperometric sensing of ethanol at the nano-Au/SiO₂/GCE in combination with alcohol dehydrogenase and nicotinamide adenine dinucleotide was successfully demonstrated. A wide linear response was also found for ethanol in the range from 5.0?×?10^?5 to 1.0?×?10^?3 mol?L^?1 and 1.0?×?10^?3 to 1.0?×?10^?2 mol?L^?1, respectively. The method was successfully applied to determine ethanol in beer and biological samples.     

Preparation of Polypyrrole/Nuclear Fast Red Films on Gold Electrode and Its Application on the Electrocatalytic Determination of Methyl‐dopa and Ascorbic Acid

A novel voltammetric method using the Ppyox/NFR/Au (poly pyrrole – nuclear fast red – gold) modified electrode was developed for simultaneous measurement of various combinations of ascorbic acid (AA) and methyldopa (MDA). Polypyrrole film was prepared by incorporation of nuclear fast red (NFR) as doping anion, during the electropolymerization of pyrrole onto a gold (Au) electrode in aqueous solution using cyclic voltammetric (CV) method, and then it was overoxidized at constant potential. Differential pulse voltammetry was utilized for the measurement of both analytes using modified electrode. Well‐separated voltammetric peaks were observed for ascorbic acid (AA) and methyldopa at the Ppyox/NFR/Au modified electrodes with peak separation of 0.210 V. It has been found that under optimum condition (pH 3.0), the oxidation of AA and MDA at the surface of the electrode occurs at a potential about 260 and 50 mV less positive than unmodified Au electrode respectively. The current catalytic oxidation peaks showed a linear dependent on the concentration of AA and MDA in the range of 9.0×10^?6 to 1.0×10^?3 and 1.0×10^?7 to 2.0×10^?5 mol L^?1 respectively. The detection limit of 5.8×10^?6 and 5.0×10^?8 mol L^?1 (S/N=3) were obtained for AA and MDA respectively. The modified electrode was used for determination of AA and MDA in some real samples such as human serum and tablet.     

Electrochemical determination of ferulic acid in Chinese traditional medicine Xiao Yao Pills at electrode modified with carbon nanotube

The electrochemical behaviors of ferulic acid were investigated at the glassy carbon electrode modified with multi-walled carbon nanotube. In pH 5.5, 0.1 mol l⁻¹ HAc-NaAc buffer solution, ferulic acid exhibited a pair of stable and sensitive redox signals at the modified electrode. The reaction mechanism was explored. Through the cyclic voltammetry, trace amount of ferulic acid was detected quantitatively. In the range of 1 × 10⁻⁵ to 5 × 10⁻³ mol l⁻¹, the oxidation peak currents of ferulic acid have a linear relationship to the concentrations, the limit of detection was estimated to be 1 × 10⁻⁷ mol l⁻¹ (S/N = 3). The influences of substrate, pH and interference of coexisting substances were investigated for response properties of the electrode. Actual Xiao Yao Pill samples were analyzed and satisfactory results were obtained, which meant that the method could be used to detect the trace amount of ferulic acid in medicament. The article is published in the original. Published in Elektrokhimiya in Russian, 2009, Vol. 45, No. 2, pp. 180–184.     

In Vivo Determination of Tetrahydrobiop- terin and Monoamine Neurotransmitters in Rat Brain by Liquid Chromatography with a Nano Crystalline Mn-Doped Lead Dioxide Film Modified Electrode

The fabrication and application of a novel electrochemical detector (ED) with nano crystalline Mn-doped lead dioxide film chemically modified electrode (CME) for liquid chromatography (LC) were described. The Mn-doped PbO₂ film was characterized by scanning tunnel microscope. The electrochemical behaviors of tetrahydrobiopterin, monoamine neurotransmitters and their metabolites at the CME were investigated by cyclic voltammetry and differential pulse voltammetry. It was found that the CME exhibited efficiently electrocatalytic effect on the current response of the seven analytes and the linear ranges of them were over three orders of magnitude with the detection limits being 5.0 × 10^?10 mol L^?1 for tetrahydrobiopterin, 2.5 × 10^?10 mol L^?1 for dopamine, 2.0 × 10^?10 mol L^?1 for norepinephrine, 5.0 × 10^?10 mol L^?1 for serotonin, 4.0 × 10^?10 mol L^?1 for 3,4-dihydroxyphenylacetic acid, 2.0 × 10^?9 mol L^?1 for homovanillic acid, 1.0 × 10^?9 mol L^?1 for 5-hydroxyindoleacetic acid. For its stability, sensitivity, convenience in preparing and long-life of activity, the Mn-doped PbO₂ electrode is therefore suitable for determination of real samples. Coupled with microdialysis sampling, the application of this method for the analysis of tetrahydrobiopterin, monoamine neurotransmitters and their metablites in rat brain was satisfactory.     

An amperometric sensor for uric acid based on ordered mesoporous carbon-modified pyrolytic graphite electrode

A novel amperometric sensor for uric acid based on ordered mesoporous carbon modified pyrolytic graphite electrode was developed. Uric acid oxidation was easily catalyzed by this electrode in a phosphate buffer solution at pH 7.0, with an anodic potential decrease about 140 mV compared to bare pyrolytic graphite electrode. The uric acid level was determined by the amperometric method, at a constant potential of 0.31 mV, the catalytic current of uric acid vs. its concentration showed a good linearity in the range of 1.0 × 10⁻⁶−1.0 × 10⁻⁴ mol L⁻¹, with a correlation coefficient of 0.999. The detection limit was 4.0 × 10⁻⁷ mol L⁻¹. The proposed method could be effectively used for uric acid amperometric sensing in human urine.     

Meldola's Blue Immobilized on a SiO2/SnO2/Phosphate Xerogel,a New Sensor for Determination of Ascorbic Acid in Medicine and Commercial Fruit Juice

A modified carbon paste electrode with SiO₂/SnO₂/Phosphate/Meldola's blue, SSPMelB, was used to study the electrocatalytic oxidation of ascorbic acid by cyclic voltammetry and chronoamperometry. The adsorbed dye mediates ascorbic acid oxidation at an anodic potential of 0.04 V vs. saturated calomel electrode (SCE) at pH 7.0, in 0.5 mol L^?1 solution. The linear range of the sensor is between 4.0×10^?7 and 2.0×10^?3 mol L^?1, with a limit of detection of 4.0×10^?7 mol L^?1. This novel electrode shows good analytical performance for determination of ascorbic acid in medicine and commercial fruit juice.     

Construction of a modified carbon paste electrode based on TiO2 nanoparticles for the determination of gallic acid

A modified carbon paste electrode was prepared by incorporating the TiO₂ nanoparticles in the carbon paste matrix. The electrochemical behavior of gallic acid (GA) is investigated on the surface of the electrode using cyclic voltammetry and differential pulse voltammetry. The surface morphology of the prepared electrode was characterized using the scanning electron microscopy. The results indicate that the electrochemical response of GA is improved significantly at the modified electrode compared with the unmodified electrode. Furthermore, the capabilities of electron transfer on these two electrodes were also investigated by electrochemical impedance spectroscopy. Under the optimized condition, a linear dynamic range of 2.5?×?10^?6 to 1.5?×?10^?4?mol?L^?1 with detection limit of 9.4?×?10^?7?mol?L^?1 for GA is obtained in buffered solutions with pH 1.7. Finally, the proposed modified electrode was successfully used in real sample analysis.     

Simultaneous determination of dopamine and serotonin by use of covalent modification of 5-hydroxytryptophan on glassy carbon electrode

An electrochemical biosensor was fabricated by covalent modification of 5-hydroxytryptophan (5-HTP) on the surface of glassy carbon electrode (GCE). The electrode, denoted as 5-HTP/GCE, was characterized by X-ray photoelectron spectroscopy, cyclic voltammetry and differential pulse voltammetry. For comparison, tryptophan modified GCE (TRP/GCE) and serotonin modified GCE (5-HT/GCE) were prepared by the same method. It was found that electrocatalytic ability of these electrodes was in the order of 5-HTP/GCE?>?TRP/GCE?>?5-HT/GCE for the oxidation of dopamine (DA) and 5-HT. The sensor was effective to simultaneously determine DA and 5-HT in a mixture. It can resolve the overlapping anodic peaks into two well-defined voltammetric peaks at 0.24 and 0.39 V (versus SCE). The linear response is in the range of 5.0?×?10^?7–3.5?×?10^?5 mol L^?1 with a detection limit of 3.1?×?10^?7 mol L^?1 for DA, and in the range of 5.0?×?10^?6–3.5?×?10^?5 mol L^?1 with a detection limit of 1.7?×?10^?6 mol L^?1 for 5-HT (s/n?=?3), respectively.     

Determination of Chlorpromazine Hydrochloride with a Layered Double Hydroxide Modified Glassy Carbon Electrode as a Nanocatalyst

We report a simple and sensitive voltammetric sensor for the determination of chlorpromazine (CPZ) based on Ni?Al layered double hydroxide (NiAlLDH) modified glassy carbon electrode (GCE). NiAlLDH was simply electrodeposited on GCE surface in a very short time. The response linear range was 1×10^?3–1×10^?9 mol L^?1, with a detection limit of 1×10^?9 mol L^?1. The NiAlLDH film showed well defined and well separate peaks for dopamine, ascorbic acid, uric acid and CPZ in the same solution. The proposed electrode was used to measure the active pharmaceutical ingredient of CPZ tablet as a real sample.     

Direct Electroanalytical Determination of Fluvastatin in a Pharmaceutical Dosage Form: Batch and Flow Analysis

Abstract

The reduction of luvastatin (FLV) at a hanging mercury-drop electrode (HMDE) was studied by square-wave adsorptive-stripping voltammetry (SWAdSV). FLV can be accumulated and reduced at the electrode, with a maximum peak current intensity at a potential of approximately ?1.26 V vs. AgCl/Ag, in an aqueous electrolyte solution of pH 5.25. The method shows linearity between peak current intensity and FLV concentration between 1.0 × 10^?8 and 2.7 × 10^?6 mol L^?1. Limits of detection (LOD) and quantification (LOQ) were found to be 9.9 × 10^?9 mol L^?1 and 3.3 × 10^?8 mol L^?1, respectively.

Furthermore, FLV oxidation at a glassy carbon electrode surface was used for its hydrodynamic monitoring by amperometric detection in a flow-injection system. The amperometric signal was linear with FLV concentration over the range 1.0 × 10^?6 to 1.0 × 10^?5 mol L^?1, with an LOD of 2.4 × 10^?7 mol L^?1 and an LOQ of 8.0 × 10^?7 mol L^?1. A sample rate of 50 injections per hour was achieved.

Both methods were validated and showed to be precise and accurate, being satisfactorily applied to the determination of FLV in a commercial pharmaceutical.     

Simultaneous Determination of Dopamine and Ascorbic Acid Using the Nano‐Gold Self‐Assembled Glassy Carbon Electrode

Electrochemical behavior of dopamine (DA) was investigated at the gold nanoparticles self‐assembled glassy carbon electrode (GNP/LC/GCE), which was fabricated by self‐assembling gold nanoparticles on the surface of L ‐cysteine (LC) modified glassy carbon electrode (GCE) via successive cyclic voltammetry (CV). A pair of well‐defined redox peaks of DA on the GNP/LC/GCE was obtained at E_pa=0.197 V and E_pc=0.146 V, respectively. And the peak separation between DA and AA is about 0.2 V, which is enough for simultaneous determination of DA and AA. The peak currents of DA and AA were proportional with their concentrations in the range of 6.0×10^?8–8.5×10^?5 mol L^?1 and 1.0×10^?6–2.5×10^?3 mol L^?1, with the detection limit of 2.0×10^?8 mol L^?1 and 3.0×10^?7 mol L^?1 (S/N=3), respectively. The modified electrode exhibits an excellent reproducibility, sensibility and stability for simultaneous determination of DA and AA in human serum with satisfactory result.     

Simultaneous voltammetric measurement of ascorbic acid and dopamine on poly(caffeic acid)-modified glassy carbon electrode

A poly(caffeic acid) thin film was deposited on the surface of a glassy carbon electrode by potentiostatic technique in an aqueous solution containing caffeic acid. The poly(caffeic acid)-modified electrode was used for the determination of ascorbic acid (AA), dopamine (DA), and their mixture by cyclic voltammetry. This modified electrode exhibited a potent and persistent electron-mediating behavior followed by well-separated oxidation peaks toward AA and DA at a scan rate of 10 mV s⁻¹ with a potential difference of 135 mV, which was large enough to determine AA and DA individually and simultaneously. The catalytic peak current obtained was linearly dependent on the AA and DA concentrations in the range of 2.0 × 10⁻⁵−1.2 × 10⁻³ and 1.0 × 10⁻⁶−4.0 × 10⁻⁵ mol L⁻¹ in 0.15 mol L⁻¹ phosphate buffer (pH 6.64). The detection limits for AA and DA were 9.0 × 10⁻⁶ and 4.0 × 10⁻⁷ mol L⁻¹, respectively. The modified electrode shows good sensitivity, selectivity, and stability and has been applied to the determination of DA and AA in real samples with satisfactory results.     

Electrode Based on Nickel‐containing SBA‐15 for the Determination of Copper in Ethanol Biofuel

A sensor based in a graphite–polyurethane composite electrode modified with the mesoporous nanostructured silica with hexagonal array of pores called Santa Barbara Amorphous type material (SBA‐15) containing nickel was built. The presence of Ni, incorporated during the synthesis of SBA‐15, resulted in an increase in sensitivity when compared to the other electrodes based on the unmodified SBA‐15. A procedure was proposed for the determination of Cu²⁺ in ethanol biofuel by square wave stripping voltammetry with linear response in concentration levels of 1.0×10^?8 and 1.0×10^?7 mol L^?1, resulting in a limit of detection of 1.83×10^?10 mol L^?1 and precision (RSD) of 2.09 %.     

Chemometric Strategies to Develop a Nanocomposite Electrode for Simultaneous Determination of Ascorbic Acid,Dopamine, and Uric Acid

A simple and sensitive method for simultaneously measuring dopamine (DA), ascorbic acid (AA), and uric acid (UA) using a poly(1‐aminoanthracene) and carbon nanotubes nanocomposite electrode is presented. The experimental parameters for composite film synthesis as well as the variables related to simultaneous determination of DA, AA, and UA were optimized at the same time using fractional factorial and Doehlert designs. The use of carbon nanotubes and poly(1‐aminoanthracene) in association with a cathodic pretreatment led to three well‐defined oxidation peaks at potentials around ?0.039, 0.180 and 0.351 V (vs. Ag/AgCl) for AA, DA, and UA, respectively. Using differential pulse voltammetry, calibration curves for AA, DA, and UA were obtained over the range of 0.16–3.12×10^?3 mol L^?1, 3.54–136×10^?6 mol L^?1, and 0.76–2.92×10^?3 mol L^?1, with detection limits of 3.95×10^?5 mol L^?1, 2.90×10^?7 mol L^?1, and 4.22×10^?5 mol L^?1, respectively. The proposed method was successfully applied to determine DA, AA, and UA in biological samples with good results.     

Differential Pulse Voltammetric Determination of Selenocystine and Selenomethionine Using SAM nanoSe0/Vc/SeCys‐Film Modified Au Electrode

The SAM nanoSe⁰/Vc/SeCys‐film modified Au electrode has been prepared to determine selenocystine and selenomethionine. The AFM and SEM showed the special three‐dimensional (3D) network structure of the sol‐gel films. The affinity between nanoparticles and biomolecules created special chemical characters analyzed by the XRD and fluorescence. The modified electrode was characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The modified films partly had resistance in the charge transduction of Fe(CN) , but the less electron‐transfer resistance. Differential pulse voltammetric (DPV) determination of selenoamino acids using SAM nanoSe⁰/Vc/SeCys‐film modified Au electrode was presented. In PBS (pH 7.0)+0.1 mol L^?1 NaClO₄ solution, selenoamino acids yielded a sensitive reduction peak at about +400±50 mV. The peak current had a linear relationship with the concentration of selenoamino acids in the range of 5.0×10^?8–1.0×10^?5 mol L^?1, and a 3σ detection limit of selenoamino acids was 1.2×10^?8 mol L^?1. The relative standard deviation of DPV signals of 0.50×10^?6 mol L^?1 selenoamino acids was 3.8% (n=8) using the same electrode and was 4.4% (n=5) when using three modified electrodes prepared at different times. The content of selenoamino acids in the organo‐selenium powder were determined by DPV. The results showed 71.5 μg g^?1 of SeCys and 65.1 μg g^?1 of SeMet in the organo‐selenium powder.     

Determination of Folic Acid by Adsorptive Stripping Voltammetry at a Lead Film Electrode

An adsorptive stripping voltammetric procedure for the determination of folic acid at an in situ plated lead film electrode was described. Formation of lead film on a glassy carbon substrate and accumulation of folic acid was performed simultaneously from an acetate buffer solution of pH 5.6 at the potential ?0.88 V. The measurements were carried out from aerated solutions. The calibration graph for an accumulation time of 300 s was linear from 2×10^?9 to 5×10^?8 mol L^?1. The detection limit was 7×10^?10 mol L^?1, the relative standard deviation for 2×10^?8 mol L^?1 of folic acid was 3.9%. The proposed procedure was applied to folic acid determinations in pharmaceutical preparations.