Electrochemical oxidation determination and voltammetric behaviour of 4-nitrophenol based on Cu2O nanoparticles modified glassy carbon electrode

Cu₂O nanoparticles (nano-Cu₂O) modified glassy carbon electrode (GCE) was fabricated and used to investigate the electrochemical behaviour of 4-nitrophenol (4-NP) by cyclic voltammetry (CV), chronoamperometry (CA), chronocoulometry (CC) and differential pulse voltammetry (DPV). Compared with GCE, a remarkable increase in oxidation peak current was observed. It indicates that nano-Cu₂O exhibits remarkable enhancement effect on the electrochemical oxidation of 4-NP. Under the optimised experimental conditions, the oxidation peak currents were propotional to 4-NP concentration in the range from 1.0?×?10^?6 to 4.0?×?10^?4?mol?L^?1 with a detection limit of 5.0?×?10^?7?mol?L^?1 (S/N?=?3). The fabricated electrode presented good repeatability, stability and anti-interference. Finally, the proposed method was applied to determine 4-NP in water samples. The recoveries for these samples were from 94.60% to 105.5%.     

Sensitive and Selective Detection of Dopamine Using a DNA Immobilized Ethylenedidamine/Polyglutamic Modified Electrode

DNA was attached on the surface of an ethylenedidamine/polyglutamic(En/PGA) modified glassy carbon electrode (GCE) to create a novel voltammetric sensor (DNA/En/PGA/GCE) for dopamine (DA). This modified electrode exhibited a linear voltammetric response for DA in the range from 1.0×10^?7 mol L^?1 to 1×10^?5 mol L^?1, with a detection limit of 2×10^?8 mol L^?1. The detection of DA was found to be unaffected by the presence of ascorbic acid, uric acid, serotonin and folic acid. The method proposed was applied to detect DA in pharmaceutical dosage and human blood serum with good satisfactory results.     

Electrocatalytic Behavior of Glassy Carbon Electrodes Modified with Multiwalled Carbon Nanotubes and Cobalt Phthalocyanine for Selective Analysis of Dopamine in Presence of Ascorbic Acid

This work describes the development, electrochemical characterization and utilization of a cobalt phthalocyanine modified carbon nanotube electrode for the quantitative determination of dopamine in 0.2 mol L^?1 phosphate buffer contaminated with high concentration of ascorbic acid. The electrode surface was analyzed by cyclic voltammetry and electrochemical impedance spectroscopy which showed a modified surface presenting a charge transfer resistance of 500 Ω, against the 16.46 kΩ value found for the bare glassy carbon surface. A pseudo rate constant value of 5.4×10^?4 cm s^?1 for dopamine oxidation was calculated. Voltammetric experiments showed a shift of the peak potential of DA oxidation to less positive value at 390 mV as compared with that of a bare GC electrode at 570 mV. The electrochemical determination of dopamine, in presence of ascorbic acid in concentrations up to 0.1 mol L^?1 by differential pulse voltammetry, yielded a detection limit as low as 2.56×10^?7 mol L^?1.     

Improvement of Selectivity and Stability of Amperometric Detection of Hydrogen Peroxide Using Prussian Blue‐PAMAM Supramolecular Complex Membrane as a Catalytic Layer

A novel hydrogen peroxide (H₂O₂) sensor was fabricated by using a submonolayer of 3‐mercaptopropionic acid (3‐MPA) adsorbed on a polycrystalline gold electrode further reacted with poly(amidoamine) (PAMAM) dendrimer (generation 4.0) to obtain a film on which Prussian Blue (PB) was later coordinated to afford a mixed and stable electrocatalytic layer for H₂O₂ reduction. On the basis of the electrochemical behaviors, atomic force microscopy (AFM) and X‐ray photoelectron spectra (XPS), it is suggested that the PB molecules are located within the dendritic structure of the surface attached PAMAM dendrimers. It was found that the PB/PAMAM/3‐MPA/Au modified electrode showed an excellent electrocatalytic activity for H₂O₂ reduction. The effects of applied potential and pH of solution upon the response of the modified electrode were investigated for an optimum analytical performance. Even in the presence of dissolved oxygen, the sensor exhibited highly sensitive and rapid response to H₂O₂. The steady‐state cathodic current responses of the modified electrode obtained at ?0.20 V (vs. SCE) in air‐saturated 0.1 mol L^?1 phosphate buffer solution (PBS, pH 6.50) showed a linear relationship to H₂O₂ concentration ranging from 1.2×10^?6 mol L^?1 to 6.5×10^?4 mol L^?1 with a detection limit of 3.1×10^?7 mol L^?1. Performance of the electrode was evaluated with respected to possible interferences such as ascorbic acid and uric acid etc. The selectivity, stability, and reproducibility of the modified electrode were satisfactory.     

铜氮杂配合物修饰金电极对抗坏血酸的分析测定

本实验制备了一种新型的氮杂铜配合物修饰金电极,该电极可用于抗坏血酸的测定。采用循环伏安法和扫描电化学显微镜技术对电极进行了表征。该修饰电极可催化氧化抗坏血酸,相对于裸电极抗坏血酸在修饰电极上氧化电位移动了250mV,并且氧化电流在抗坏血酸的浓度为5.0×10−7 to 4.0×10−5 mol/L时呈线性关系,检测限为4.8×10-8 mol/L。用此方法测定抗坏血酸与文献报道的测定结果一致,这表明该电极可用作抗坏血酸测定的电化学传感器。     

In Vivo Determination of Tetrahydrobiop- terin and Monoamine Neurotransmitters in Rat Brain by Liquid Chromatography with a Nano Crystalline Mn-Doped Lead Dioxide Film Modified Electrode

The fabrication and application of a novel electrochemical detector (ED) with nano crystalline Mn-doped lead dioxide film chemically modified electrode (CME) for liquid chromatography (LC) were described. The Mn-doped PbO₂ film was characterized by scanning tunnel microscope. The electrochemical behaviors of tetrahydrobiopterin, monoamine neurotransmitters and their metabolites at the CME were investigated by cyclic voltammetry and differential pulse voltammetry. It was found that the CME exhibited efficiently electrocatalytic effect on the current response of the seven analytes and the linear ranges of them were over three orders of magnitude with the detection limits being 5.0 × 10^?10 mol L^?1 for tetrahydrobiopterin, 2.5 × 10^?10 mol L^?1 for dopamine, 2.0 × 10^?10 mol L^?1 for norepinephrine, 5.0 × 10^?10 mol L^?1 for serotonin, 4.0 × 10^?10 mol L^?1 for 3,4-dihydroxyphenylacetic acid, 2.0 × 10^?9 mol L^?1 for homovanillic acid, 1.0 × 10^?9 mol L^?1 for 5-hydroxyindoleacetic acid. For its stability, sensitivity, convenience in preparing and long-life of activity, the Mn-doped PbO₂ electrode is therefore suitable for determination of real samples. Coupled with microdialysis sampling, the application of this method for the analysis of tetrahydrobiopterin, monoamine neurotransmitters and their metablites in rat brain was satisfactory.     

Sensitive electrochemical determination of Sudan II in food samples using a poly(aminosulfonic acid) modified glassy carbon electrode

In this paper, a novel poly(aminosulfonic acid) modified glassy carbon electrode (PASA/GCE) for the determination of Sudan II was fabricated through electrochemical polymerizat ion. The electrochemical behavior of Sudan II at the modified electrode was studied by cyclic voltammetry. Results show that the modified electrode exhibits excellent electrocatalytic activity toward the electrochemical redox reaction of Sudan II. Under optimal experimental conditions, the oxidation peak current is linearly proportional to the concentration of Sudan II in the ranges of 4.0 × 10^?8 to 1.0 × 10^?6 mol L^?1 and 1.0 × 10^?6 to 1.2 × 10^?5 mol L^?1. The linear regression equations are i _pa(A) = 2.87c + 3.74 × 10^?6, r = 0.9977 and i _pa(A) = 0.78c + 6.11 × 10^?6, r = 0.9982, respectively, and the detection limit is 4.0 × 10^?9 mol L^?1. The novel method shows good recovery, reproducibility and sensitivity for the voltammetric determination of Sudan II in food samples.     

Simultaneous Voltammetric Detection of Salsolinol and Uric Acid in the Presence of High Concentration of Ascorbic Acid with Gold Nanoparticles/Functionalized Multiwalled Carbon Nanotubes Composite Film Modified Electrode

This work demonstrates gold nanoparticles (AuNPs)/functionalized multiwalled carbon nanotubes (f‐MWCNT) composite film modified gold electrode via covalent‐bonding interaction self‐assembly technique for simultaneous determination of salsolinol (Sal) and uric Acid (UA) in the presence of high concentration of ascorbic acid (AA). In pH 7.0 PBS, the composite film modified electrode exhibits excellent voltammetric response for Sal and UA, while AA shows no voltammetric response. The oxidation peak current is linearly increased with concentrations of Sal from 0.24–11.76 μmol L^?1 and of UA from 3.36–96.36 μmol L^?1, respectively. The detection limits of Sal and UA is 3.2×10^?8 mol L^?1 and 1.7×10^?7 mol L^?1 , respectively.     

Preparation of Polypyrrole/Nuclear Fast Red Films on Gold Electrode and Its Application on the Electrocatalytic Determination of Methyl‐dopa and Ascorbic Acid

A novel voltammetric method using the Ppyox/NFR/Au (poly pyrrole – nuclear fast red – gold) modified electrode was developed for simultaneous measurement of various combinations of ascorbic acid (AA) and methyldopa (MDA). Polypyrrole film was prepared by incorporation of nuclear fast red (NFR) as doping anion, during the electropolymerization of pyrrole onto a gold (Au) electrode in aqueous solution using cyclic voltammetric (CV) method, and then it was overoxidized at constant potential. Differential pulse voltammetry was utilized for the measurement of both analytes using modified electrode. Well‐separated voltammetric peaks were observed for ascorbic acid (AA) and methyldopa at the Ppyox/NFR/Au modified electrodes with peak separation of 0.210 V. It has been found that under optimum condition (pH 3.0), the oxidation of AA and MDA at the surface of the electrode occurs at a potential about 260 and 50 mV less positive than unmodified Au electrode respectively. The current catalytic oxidation peaks showed a linear dependent on the concentration of AA and MDA in the range of 9.0×10^?6 to 1.0×10^?3 and 1.0×10^?7 to 2.0×10^?5 mol L^?1 respectively. The detection limit of 5.8×10^?6 and 5.0×10^?8 mol L^?1 (S/N=3) were obtained for AA and MDA respectively. The modified electrode was used for determination of AA and MDA in some real samples such as human serum and tablet.     

Chemometric Strategies to Develop a Nanocomposite Electrode for Simultaneous Determination of Ascorbic Acid,Dopamine, and Uric Acid

A simple and sensitive method for simultaneously measuring dopamine (DA), ascorbic acid (AA), and uric acid (UA) using a poly(1‐aminoanthracene) and carbon nanotubes nanocomposite electrode is presented. The experimental parameters for composite film synthesis as well as the variables related to simultaneous determination of DA, AA, and UA were optimized at the same time using fractional factorial and Doehlert designs. The use of carbon nanotubes and poly(1‐aminoanthracene) in association with a cathodic pretreatment led to three well‐defined oxidation peaks at potentials around ?0.039, 0.180 and 0.351 V (vs. Ag/AgCl) for AA, DA, and UA, respectively. Using differential pulse voltammetry, calibration curves for AA, DA, and UA were obtained over the range of 0.16–3.12×10^?3 mol L^?1, 3.54–136×10^?6 mol L^?1, and 0.76–2.92×10^?3 mol L^?1, with detection limits of 3.95×10^?5 mol L^?1, 2.90×10^?7 mol L^?1, and 4.22×10^?5 mol L^?1, respectively. The proposed method was successfully applied to determine DA, AA, and UA in biological samples with good results.     

The electrochemistry of uric acid at a gold electrode modified with L-cysteine, and its application to sensing uric urine

The electrochemistry of uric acid at a gold electrode modified with a self-assembled film of L-cysteine was studied by cyclic voltammetry and differential pulse voltammetry. Compared to the bare gold electrode, uric acid showed better electrochemical response in that the anodic peak current is stronger and the peak potential is negatively shifted by about 100 mV. The effects of experimental conditions on the oxidation of uric acid were tested and a calibration plot was established. The differential pulse response to uric acid is linear in the concentration range from 1.0?×?10^?6 to ~?1.0?×?10^?4 mol?L^?1 (r?=?0.9995) and from 1.0?×?10^?4 to ~?5.0?×?10^?4 mol?L^?1 (r?=?0.9990), the detection limit being 1.0?×?10^?7 mol?L^?1 (at S/N?=?3). The high sensitivity and good selectivity of the electrode was demonstrated by its practical application to the determination of uric acid in urine samples.

Electrochemical determination of ascorbic acid using the poly-cysteine film-modified electrode

A poly(L-cysteine) thin film was prepared onto electrode surface via electropolymerization. In pH 7.0 phosphate buffer, L-cysteine was oxidized during the cyclic potential sweep between −0.60 and 2.00 V, forming a thin film at the glassy carbon electrode (GCE) surface. The electrochemical behaviors of ascorbic acid at the bare GCE and the poly(L-cysteine) film-coated GCE were investigated. The oxidation peak potential of ascorbic acid shifts to more negative potential at the poly(L-cysteine) film-modified GCE. Moreover, the oxidation peak current significantly increases at the poly(L-cysteine) film-modified GCE. These phenomena indicate that poly(L-cysteine) film shows highly-efficient catalytic activity to the oxidation of ascorbic acid. Based on this, a sensitive and simple electrochemical method was proposed for the determination of ascorbic acid. The oxidation peak current of ascorbic acid is proportional to its concentration over the range from 1.0 × 10⁻⁶ to 5.0 × 10⁻⁴ mol l⁻¹. The limit of detection is evaluated to be 4.0 × 10⁻⁷ mol l⁻¹.     

One-step construction of an electrode modified with electrodeposited Au/SiO2 nanoparticles, and its application to the determination of NADH and ethanol

A new electrode was developed by one-step potentiostatic electrodeposition (at ?2.0 V for 20 s) of Au/SiO₂ nanoparticles on a glassy carbon electrode. The resulting electrode (nano-Au/SiO₂/GCE) was characterized by scanning electronic microscopy, X-ray photoelectron spectroscopy and electrochemical techniques. The electrochemical behavior of dihydronicotinamide adenine dinucleotide (NADH) at the nano-Au/SiO₂/GCE were thoroughly investigated. Compared to the unmodified electrode, the overpotential decreased by about 300 mV, and the current response significantly increased. These changes indicated that the modified electrode showed excellent catalytic activity in the oxidation of NADH. A linear relationship was obtained in the NADH concentration range from 1.0?×?10^?6 to 1.0?×?10^?4 mol?L^?1. In addition, amperometric sensing of ethanol at the nano-Au/SiO₂/GCE in combination with alcohol dehydrogenase and nicotinamide adenine dinucleotide was successfully demonstrated. A wide linear response was also found for ethanol in the range from 5.0?×?10^?5 to 1.0?×?10^?3 mol?L^?1 and 1.0?×?10^?3 to 1.0?×?10^?2 mol?L^?1, respectively. The method was successfully applied to determine ethanol in beer and biological samples.     

Determination of ferulic acid in Chinese proprietary medicine based on a poly-glutamic acid film sensor

The poly-glutamic acid modified electrode has been prepared by direct electro-polymerization of D-glutamic acid on the surface of glassy carbon electrode. In pH 4.2, 0.1 mol L^?1 HAc-NaAc buffer solution, the film modified electrode exhibited remarkable enhancement effect to the electrochemical responses of ferulic acid. The action mechanism was preliminarily explored. In the range of 2.0 × 10^?7 to 1.0 × 10^?5 mol L^?1, and 1.0 × 10^?5 to 3.0 × 10^?4 mol L^?1, the oxidation peak current has a linear relationship to the concentration, and the detection limit was estimated to be 7.0 × 10^?8 mol L^?1. This method has been adopted to detect trace amount of ferulic acid in Chinese proprietary medicine, and the recovery was from 97.8 to 102.4%.     

Construction of a modified carbon paste electrode based on TiO2 nanoparticles for the determination of gallic acid

A modified carbon paste electrode was prepared by incorporating the TiO₂ nanoparticles in the carbon paste matrix. The electrochemical behavior of gallic acid (GA) is investigated on the surface of the electrode using cyclic voltammetry and differential pulse voltammetry. The surface morphology of the prepared electrode was characterized using the scanning electron microscopy. The results indicate that the electrochemical response of GA is improved significantly at the modified electrode compared with the unmodified electrode. Furthermore, the capabilities of electron transfer on these two electrodes were also investigated by electrochemical impedance spectroscopy. Under the optimized condition, a linear dynamic range of 2.5?×?10^?6 to 1.5?×?10^?4?mol?L^?1 with detection limit of 9.4?×?10^?7?mol?L^?1 for GA is obtained in buffered solutions with pH 1.7. Finally, the proposed modified electrode was successfully used in real sample analysis.     

Fabrication of a New Self-assembly Compound of CsTi<Subscript>2</Subscript>NbO<Subscript>7</Subscript> with Cationic Cobalt Porphyrin Utilized as an Ascorbic Acid Sensor

A novel sandwich-structured nanocomposite based on Ti₂NbO₇^? nanosheets and cobalt porphyrin (CoTMPyP) was fabricated through electrostatic interaction, in which CoTMPyP has been successfully inserted into the lamellar spacing of layered titanoniobate. The resultant Ti₂NbO₇/CoTMPyP nanocomposite was characterized by XRD, SEM, TEM, EDS, FT-IR, and UV-vis. It is demonstrated that the intercalated CoTMPyP molecules were found to be tilted approximately 63° against Ti₂NbO₇^? layers. The glass carbon electrode (GCE) modified by Ti₂NbO₇/CoTMPyP film showed a fine diffusion-controlled electrochemical redox process. Furthermore, the Ti₂NbO₇/CoTMPyP-modified electrode exhibited excellent electrocatalytic oxidation activity of ascorbic acid (AA). Differential pulse voltammetric studies demonstrated that the intercalated nanocomposite detects AA linearly over a concentration range of 4.99?×?10^?5 to 9.95?×?10^?4 mol L^?1 with a detection limit of 3.1?×?10^?5 mol L^?1 at a signal-to-noise ratio of 3.0.     

Electrochemical Morphine Sensor Based on Gold Nanoparticles Metalphthalocyanine Modified Carbon Paste Electrode

Composites of gold nanoparticles (Au) electrochemically deposited and different metal phthalocyanines (Co, Ni, Cu, and Fe) were chemically prepared. The composites were used as modifiers for carbon paste electrodes and were used for the determination of morphine in presence of ascorbic acid and uric acid. Central metal atoms of phthalocyanine moiety affected the rate of electron transfer. Thus, the electroactivity of different modifiers were evaluated towards morphine oxidation. Au‐CoPcM‐CPE possessed the highest rate for charge transfer rate in all studied pH electrolytes. Limit of detection was 5.48×10^?9 mol L^?1 in the range of 4.0×10^?7 to 9.0×10^?4 mol L^?1.     

Electrochemical Behavior of Chloranil Chemically Modified Carbon Paste Electrode. Application to the Electrocatalytic Determination of Ascorbic Acid

A p‐chloranil modified carbon paste electrode was constructed and the electrochemical behavior of this electrode was studied in the aqueous solution with different pH. From the E_1/2–pH diagram for this compound the values of formal potential E^0' and pK_a of some different redox and acid‐base couples depending on the solution pH were estimated. The diffusion coefficient, D, value for p‐chloranil was estimated 1.5×10^?7 cm² s^?1. It has been shown by direct current cyclic voltammetry and double potential step chronoamperometry, that this p‐chloranil incorporated carbon paste electrode, can catalyze the oxidation of ascorbic acid in the aqueous buffered solution. Under the optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 325 mV less positive than that at an unmodified carbon past electrode. The catalytic oxidation peak currents was linearly dependent on the ascorbic acid concentration and a linear calibration curve was obtained in the range of 7×10^?5 M–4×10^?3 M of ascorbic acid with a correlation coefficient of 0.9998. The limit of detection (3σ) was determined as 3.5×10 ^?5 M. This method was used as simple, selective and precise voltammetric method for determination of ascorbic acid in pharmaceutical preparations.     

Electrochemical Behavior of Apigenin at a Glassy Carbon Electrode and its Analytical Application

The electrochemical behavior of the antitumor herbal drug apigenin was studied in 0.1 mol L^?1 B‐R buffer solutions (50% ethanol, pH 3.0) by cyclic voltammetry (CV) at a glassy carbon electrode. In CV, two oxidation peaks (P₁ and P₂) with E_p1 = 1.03V and E_p2 = 1.23 V appeared at a scan rate of 0.05 V s^?1, and a new electroanalytical method for this herbal drug was established according to the oxidation peak P2. The peak currents have a linear relationship with apigenin concentration in a range from 9.0 × 10^?7 to 2.0 × 10^?5 mol L^?1. Using the established method, apigenin in a herbal drug was determined without pre‐separation with satisfactory results. Moreover, the electrode dynamics parameters were also investigated by electrochemical techniques and the possible electrode reaction mechanism was deduced.     

Determination of Chlorpromazine Hydrochloride with a Layered Double Hydroxide Modified Glassy Carbon Electrode as a Nanocatalyst

We report a simple and sensitive voltammetric sensor for the determination of chlorpromazine (CPZ) based on Ni?Al layered double hydroxide (NiAlLDH) modified glassy carbon electrode (GCE). NiAlLDH was simply electrodeposited on GCE surface in a very short time. The response linear range was 1×10^?3–1×10^?9 mol L^?1, with a detection limit of 1×10^?9 mol L^?1. The NiAlLDH film showed well defined and well separate peaks for dopamine, ascorbic acid, uric acid and CPZ in the same solution. The proposed electrode was used to measure the active pharmaceutical ingredient of CPZ tablet as a real sample.