基于Fe3O4/Au/GOx的新型磁性敏感膜葡萄糖传感器研制

在核壳结构Fe3O4/Au微粒上共价固定葡萄糖氧化酶,制得磁性复合粒子Fe3O4/Au/Gox,该复合粒子保留了良好的超顺磁性。通过磁力将其固定到改进的玻碳电极上,以二茂铁为电子媒介,制得新型葡萄糖传感器。研究了该传感器的传感性能,优化了实验参数。在pH7.0的磷酸盐缓冲溶液中,葡萄糖浓度在5.0×10-5～2.0×10-2mol/L间呈良好线性关系,响应时间小于10s。该传感器有灵敏度高,选择性好,性能稳定,制作简单且易于更新的特点。     

基于壳聚糖-纳米金/纳米普鲁士蓝/L-半胱氨酸修饰的 葡萄糖传感器的研究

在金电极表面修饰一层L-半胱氨酸,再利用静电吸附作用固定纳米普鲁士蓝(nano-PB),然后利用壳聚糖-纳米金复合膜将葡萄糖氧化酶(GOD)固定于修饰电极表面,制成新型的葡萄糖传感器.通过交流阻抗技术,循环伏安法和计时电流法考察了电极的电化学特性.在优化的实验条件下,该传感器在葡萄糖浓度为3.0×10-6～1.0×10-3 mol/L范围内有线性响应,检测下限为1.6×10-6 mol/L.此外该传感器具有响应快、稳定性好和选择性良好的特点,能有效排除常见干扰物质如抗坏血酸、尿酸等对测定的影响.     

Modified electrodes from hydrophobic alkoxide silica gels—Insertion of electroactive compounds and glucose oxidase

Silica gels issued either from alkoxides or from colloidal silica are well known to be suitable materials for the immobilization of optically active probes or catalytically active chemicals. Recently it has been demonstrated that an enzyme like glucose oxidase could be immobilized into silica gels and glasses and still was able to retain a part of its activity.Recently, we have demonstrated that gels, either from silica or from transition metals, were appropriate mediums to perform electrochemistry, due to their high content of free solvent. It was a natural development of such studies to prepare modified electrodes from gels. We have developped two kinds of system.On one hand modified electrodes starting from hydrophobic DEDMS/TMMS (dimethoxydimethylsilane and trimethoxymethylsilane in various proportions) gels with small organic electroactive compounds incorporated have been prepared in which the electroactive probe is retained due to the hydrophobic balance of the gel. Such gels are adherent to the electrode and they present the electrochemistry of the electroactive probe included. Different conditions of preparation and drying of the gels are presented in relation with their influence on the behaviour of the modified electrode.On the other hand, glucose oxidase has been incorporated with a water soluble ferrocene as a mediator in silica gels made from colloids (NYACOL), and its catalytic activity has been experienced following the electrochemistry of the ferrocene. The electrochemical response in the presence of glucose is typical of the homogeneous response and the influence of the different parameters, governing the catalysis will be discussed.     

基于纳米金和硫堇固定酶的过氧化氢生物传感器

在铂电极上自组装一层纳米金(GNs), 构建负电荷的界面, 然后通过金-硫、金-氮共价键合作用和静电吸附作用自组装一层阳离子电子媒介体硫堇(Thio). 再以同样的作用自组装一层GNs和辣根过氧化酶(HRP)的混合物, 最后在电极最外层滴加一层疏水性聚合物壳聚糖(Chit), 由此制备了一种新型的过氧化氢生物传感器. 研究了工作电位、检测底液pH、温度对响应电流的影响, 以及GNs和HRP之间的相互作用, 探讨了传感器的表面形态、交流阻抗、重现性和稳定性. 该传感器的酶催化反应活化能为12.4 kJ/mol, 表观米氏常数为6.5×10^－4 mo/L, 在优化的实验条件下, 所研制的传感器对H₂O₂的线性范围为5.6×10^－5～2.6×10^－3 mol/L, 检出限为1.5×10^－5 mol/L. 应用此方法制备了HRP和葡萄糖氧化酶(GOD)双酶体系葡萄糖生物传感器, 并应用于实验样品葡萄糖含量的测定.     

钴卟啉修饰碳纤维束葡萄糖酶微电极的研究

生物电化学传感器的微型化研究是目前生物传感器研究中的一个很活跃的方向。我们曾用钴卟啉修饰碳纤维柱电极,并以它为基底制成了葡萄糖微传感器。为加强电极的抗折断能力,本文把约1千支碳纤维(φ9μm)做成碳纤维束盘微电极,在其表面修饰四苯基钴卟啉后,以其为基底制成了葡萄糖酶电极。将其用于流动注射分析,可以大大提高线性响应上限。     

Study on the United Glucose Oxidase Electrode Constructed by Composite Electrode

A novel type of united glucose oxidase (GOD) electrode was designed. Glucose oxidase and ferrocene (Fc), which was a mediator, were added into the composite electrode that was constructed by graphite powder, acetylene black, and epoxy resin. These three materials in composite electrode kept constant proportion in weight. And the optimum amounts of GOD and Fc among united enzyme electrode were 5% and 2%, respectively. The glucose was detected linearly in the concentration range 0.01–9.0 mM with a 20-s steady-state response time and 36 nA/mM of the sensitivity at 0.15 V applied potential. And electrode fouling problem and the response current from the interferents were avoided. The response current of the united GOD electrode had no obvious deterioration within 80 days when stored at 4°C in a refrigerator. The detecting results of human serum by the united GOD electrode had good consistency with that by standard enzyme method. The maximum deviation between these two detecting values was 5%. It might be used for detecting the blood sugar in clinical assay.     

姜黄素–邻二氮菲–镍配合物修饰电极的制备及其对葡萄糖的催化氧化

研究了姜黄素–邻二氮菲–镍配合物修饰电极对葡萄糖的催化氧化行为。在pH 6.0的磷酸盐缓冲液条件下,姜黄素与邻二氮菲–镍配合物聚合,附着在铂碳电极上制得姜黄素–邻二氮菲–镍配合物修饰电极,该修饰电极对葡萄糖的催化效果优于姜黄素修饰电极。在优化测试条件下,姜黄素–邻二氮菲–镍配合物修饰电极对葡萄糖测定的线性范围为6.0×10–5～3.0×10–3 mol/L,相关系数r=0.997 2。该修饰电极可用于测定血液中的葡萄糖,测定结果的相对标准偏差为2.16%～4.44%(n=10),回收率在98.2%～103.2%之间。该方法准确可靠,可用于测定血液中的葡萄糖。     

基于碳纳米管和铁氰酸镍纳米颗粒协同作用的葡萄糖生物传感器

将制备的铁氰酸镍纳米颗粒(NiNP)与多壁碳纳米管(CNT)混合, 分散于壳聚糖溶液中, 形成一种新的纳米复合成分(NiNP-CNT-CHIT), 将其修饰在玻碳电极表面. 新复合膜体现了NiNP和CNT之间的协同作用, 由于CNT的良好的传递电子性能, 促使NiNP催化氧化还原能力有了较大的提高. 此NiNP-CNT-CHIT复合膜修饰的玻碳电极在较低电位下对过氧化氢具有良好的电催化性能, 与NiNP-CHIT膜比较, 测定H₂O₂的灵敏度增大了50倍. 通过戊二醛在电极表面固定葡萄糖氧化酶制备了一种新的葡萄糖传感器. 该传感器在－0.2 V下对葡萄糖的线性范围为0.05～10 mmol/L, 检测下限为10 μmol/L.     

New Strategy for Dehydrogenase Amperometric Biosensors Using Surfactant to Enhance the Sensitivity of Diaphorase/Ferrocene Modified Carbon Paste Electrodes for Electrocatalytic Oxidation of NADH

A carbon paste electrode (CPE) modified with diaphorase (DAP) and ferrocene (FcH) has been developed for determination of NADH at low working potential. The sensitivity and operational stability, towards the detection of the reduced form of the nicotinamide adenine dinucleotide (NADH) in flow injection analysis (FIA), were greatly improved (5 times) upon adding Tween 20 into the electrode matrix. The magnitude of the amperometric signal was dependent on DAP, FcH and surfactant loading, into the modified carbon paste electrode. A rapid and repeatable response was observed to the variation of NADH concentration in the vicinity of the electrode surface. Such advantages of the DAP/FcH/Tween 20 modified carbon paste were successfully used in the construction of L ‐lactate dehydrogenase modified electrodes. The use of this new approach can be generalized to other dehydrogenases and represents a decisive step for a versatile preparation method of amperometric biosensors.     

壳聚糖固定化葡萄糖氧化酶生物传感器测定葡萄糖的含量

应用壳聚糖将葡萄糖氧化酶固定于鸡蛋膜上,结合氧电极制得葡萄糖传感器.实验表明,壳聚糖比戊二醛能更好地固定葡萄糖氧化酶,最佳条件为壳聚糖浓度0.3%、固定化酶量0.8 mg、 pH 7.0、缓冲溶液浓度300 mmol/L和温度25 ℃.本葡萄糖传感器的线性范围为0.016～1.10 mmol/L;检出限为8.0 μmol/L(S/N=3), 响应时间<60 s,有很好的稳定性,寿命>3个月.同一个传感器重复使用以及同方法制作的不同传感器之间都有很好的重现性,RSD分别为2.5%(n=10)和4.7%(n=4).实际样品中可能存在的烟酰胺、 VB6、 VB12、 VE、Ca2+、 Mg2+、 K+和Zn2+等对葡萄糖的测定不产生干扰.本传感器已成功地应用于市售饮料中葡萄糖含量的测定.     

基于金纳米棒-壳聚糖复合膜的葡萄糖生物传感器

本文采用金纳米棒-壳聚糖复合膜固定葡萄糖氧化酶构建电流型葡萄糖生物传感器.通过电化学交流阻抗法和循环伏安法对酶膜状态进行了表征,得到了相应的等效电路和动力学参数.实验结果表明,金纳米棒-壳聚糖复合膜可以辅助电子传递,提高电极的电流响应,并使生物传感器的使用温度范围有很大的扩展.此传感器表现出对葡萄糖溶液浓度的优良响应,线性范围在2.78×10^-5mol/L—2.22×10^-3mol/L,响应灵敏度约为7.819μA·cm^-2(mmol/L)^-1,表观米氏常数为10mmol/L.本工作还研究了温度和溶液pH值对电极电流响应的影响.     

一步电沉积制备交联型有机-无机生物杂化膜构筑双酶传感器的研究

利用一步电沉积法,以含有环氧基团的γ-环氧丙氧丙基三甲氧基硅烷（GPTMS）为无机杂化试剂和功能性交联试剂,通过壳聚糖（Chitosan,CS）、辣根过氧化物酶（HRP）和葡萄糖氧化酶（GOD）分子中-NH2与环氧基团的反应,在金电极表面原位制备交联型有机-无机生物杂化膜,得到共固定HRP和GOD的新型双酶生物传感器．实验证实了这种有机-无机生物杂化膜在不同酸、碱条件下都具有高的稳定性和耐用性,克服了CS酸溶的不足,从而扩大了其使用范围．在葡萄糖检测中,交联型双酶传感器HRP-GOD／GPTMS／CS,Au比无交联的双酶传感器HRP-GOD／CS／Au具有更高的灵敏度、更宽的线性范围,其线性范围为1μmol／L-351μmol／L,检期4限为0．3μmol／L．     

硅溶胶-凝胶包埋纳米金和酶的葡萄糖生物传感器

采用溶胶-凝胶技术将金纳米粒子和葡萄糖氧化酶一次性固定于硅溶胶-凝胶的网络结构中,制备了葡萄糖生物电化学传感器并优化了传感器的制备条件。酶电极对葡萄糖具有良好的电化学响应,葡萄糖浓度在0.02~2.0 mmol/L范围内和催化电流呈线性关系,检出限为0.005 mmol/L。酶电极在4 ℃下贮存100 d后对葡萄糖的响应仅下降8%。该酶电极灵敏度高、响应快、稳定性好。     

Sensitive Voltammetric Determination of Captopril Using a Carbon Paste Electrode Modified with Nano-TiO2/Ferrocene Carboxylic Acid

A carbon paste electrode (CPE) modified with ferrocene carboxylic acid (FcCA) and TiO2 nanoparticles was constructed by incorporating TiO2 nanoparticles and ferrocene carboxylic acid into the carbon paste matrix.The electrochemical behavior of captopril (CAP) at the surface of the modified electrode was investigated using electroanalytical methods.The modified electrode showed excellent electrocatalytic activity for the oxidation of CAP in aqueous solutions at physiological pH values.Cyclic voltammetric curves showed that the oxidation of CAP at the surface of the modified electrode reduced its overpotential by more than 290 mV.The modified electrode was used for detecting captopril using cyclic voltammetry and square wave voltammetry techniques.A calibration curve in the range of 0.03 to 2400μmol/L was obtained that had a detection limit of 0.0096 μmol/L (3σ) under the optimized conditions.The modified electrode was successfully used for the determination of captopril in pharmaceutical and biological samples.     

Biosensor for determination of glucose and sucrose in fruit juices by flow injection analysis

Glucose and sucrose were measured with an amperometric method by using the flow injection analysis technique. A carbon paste electrode with a renewable surface containing glucose oxidase, horseradish peroxidase, and ferrocene was used in combination with the soluble enzymes invertase and mutarotase. The effect of invertase, mutarotase, and ascorbic acid on the electrode response was examined. Glucose and sucrose concentrations were determined with <3% errors. The proposed method for glucose and sucrose measurements was validated in real samples of fruitjuices. The results were also compared with those obtained with the ultraviolet method.     

聚邻氨基酚/Ni2+修饰碳糊电极的制备及其对葡萄糖的电催化氧化

以循环伏安法在碳糊电极(CPE)表面上修饰聚邻氨基酚膜(P-OAP),再以浸泡吸附法在此膜中嵌入金属离子Ni2 ,制成Ni/P-OAP/CPE。该电极在0.09mol/LNaOH溶液中通过90圈扫描活化后,在-0.15至0.65V区间出现一对峰形良好且稳定的氧化还原峰。循环伏安实验发现,Ni/P-OAP/CPE对葡萄糖的电氧化有良好的催化特性,催化活性受薄膜的厚度、薄膜中Ni2 的浓度、电极的活化时间以及电解液组成的影响。实验结果表明:该电极是一种良好的无酶葡萄糖传感器。     

二茂铁功能化Fe3O4/碳纳米管/壳聚糖复合膜葡萄糖生物传感电极的研究

采用交联法制备了羧基二茂铁功能化Fe₃O₄纳米粒子（FMC-AFNPs）复合材料,并将该复合纳米材料与多壁碳纳米管（MWNTs）、壳聚糖（CS）及葡萄糖氧化酶（GOD）混合修饰于自制的磁性玻碳基底(MGC)表面,制备了GOD/FMC-AFNPs/MWNTs/CS复合膜生物传感器电极. 实验结果表明,FMC-AFNPs复合材料有效地克服了二茂铁在电极表面的泄漏,且FMC-AFNPs/MWNTs/CS复合膜良好的生物兼容性较大地改善了固定化GOD的生物活性. MWNTs具有良好的导电性和大比表面积,在修饰膜内可作为电子传递“导线”,极大地促进电极的电子传递速率,提高电极的电催化活性和灵敏度. 该电极的葡萄糖检测的线性范围为1.0×10^-5 ~ 6.0×10^-3 molL^-1,检测限为3.2×10^-6 mmolL^-1（S/N=3）,表观米氏常数为5.03×10^-3 mmolL^-1,且有较好的稳定性和重现性.     

Glucose Biosensor Based on the Use of a Carbon Nanotube Paste Electrode Modified with Metallic Particles

This work reports on the performance of new glucose biosensors based on the combination of the electrocatalytic properties of metals and carbon nanotubes towards the reduction of hydrogen peroxide with the biocatalytic activity of glucose oxidase (GOx). The bioelectrodes were obtained by dispersing the metal particles, enzyme and multi-wall carbon nanotubes within a mineral oil binder. The strong electrocatalytic activity of copper and iridium towards the reduction of hydrogen peroxide has made possible an important improvement in the sensitivity for the determination of glucose compared to the carbon nanotube composite without metals. A highly sensitive and selective amperometric detection of glucose becomes possible at very low potentials (−0.100 V). The presence of the protein enables a better dispersion of the metals within the composite matrix, thus allowing an additional enhancement in the response to hydrogen peroxide. The influence of the amount of copper in the composite on the analytical performance of the bioelectrode is discussed. A biosensor containing 0.77% w/w Cu and 10.0% w/w GOx gave a fast response (10.0 s), a linear relationship between current and glucose concentration up to 1.20 × 10⁻² M, and a detection limit of 2.0 × 10⁻⁵ M. A similar behavior was found for a carbon nanotube-composite electrode containing iridium.     

Ceramic Carbon/Polypyrrole Materials for the Construction of Bienzymatic Amperometric Biosensor for Glucose

Amperometric enzymatic biosensors have high selectivity and simplicity in use. It has advantages over other analytical methods in biochemistry, pharmacology, so it evokes strong interests1,2. Generally, the detection mode involved in oxidase based biosensors is often based on the electrochemical detection of hydrogen peroxide directly3,4. However the direct oxidation of hydrogen peroxide requires a relative high working potential (exceeding ca. 0.6 V vs. SCE), at which many biological sub…     

Covalent immobilization of an enzyme (glucose oxidase) onto a carbon sol-gel silicate composite surface as a biosensing platform

A porous organic-inorganic hybrid sol-gel carbon composite has been developed and used for surface covalent bonding of an enzyme for biosensing applications, illustrated by glucose oxidase (GOD). The composite comprises graphite powder, ferrocene, and an amino- and methyl-silicate backbone. The graphite powder provides the conductivity for the electrode and ferrocene acts as the mediator for signal transduction from the active center of the enzyme to the electron conductive surface. The presence of amine groups in the sol-gel silicate network allows for the covalent bonding sites for the enzyme via the carbodiimide reaction. The hydrophobicity and hydrophilicity properties of the electrode surface are controlled by the amine and methyl groups of the silicate network. Systematic optimization of the composite composition has been carried out and the performance of the glucose biosensor has been investigated. The optimal electrode gives a linear response range of 0.1-27 mM glucose with a sensitivity of 1.30 μA mM⁻¹ and detection limit (S/N = 3) of 26 μM.