Synthesis and characterization of brookite/anatase complex thin film

TiO₂ films were prepared on a silicon or soda-glass substrate using a sol suspension. The TiO₂ film on the silicon substrate was composed of pure anatase phase and showed almost no contaminations. In contrast, the TiO₂ film on the soda-glass substrate was composed of anatase and brookite phases. The diffusion of Na into the TiO₂ film on the soda-glass substrate was observed by XPS, and Na was concentrated on the surface of the film. The yield of the brookite phase increased with decreasing distance from the surface of the film on the soda-glass substrate. Na promoted the formation of the brookite phase, although the preparative procedure was used for anatase synthesis.     

Deposition of Au/TiO2 film by pulsed laser

Au nanoparticles, which were photoreduced by a Nd:YAG laser in HAuCl₄ solution containing TiO₂ colloid and accompanied by the TiO₂ particles, were deposited on the substrate surface. The film consisting of Au/TiO₂ particles was characterized by the absorption spectra, scanning electron microscopy (SEM) and X-ray diffraction (XRD) analysis. The adhesion between the film and substrate was evaluated by using adhesive tape test. It was found that the presence of TiO₂ dramatically enhanced the adhesion strength between the film and the substrate, as well as the deposition rate of film. The mechanism for the deposition of Au/TiO₂ film was also discussed.     

Highly Active TiO2/Polyelectrolytes Hybrid Multilayered Hollow Nanofibrous Photocatalyst Prepared from Electrouspun Fibers Using Electrostatic Layer-by-Layer Technique

Compared to conventional film photocatalysts, fiber photocatalyst has a greater surface-to-volume ratio and a 3-D open structure that allows its surface active sites to be accessible for reactants more easily and effectively. However, TiO ₂ powder (Degussa P25), by itself, cannot be prepared in the form of fibers, but with the help of a polymer nanofiber, TiO ₂ particles can be immobilized in a fibrous network of polyelectrolyte. Here, hybrid multilayered hollow nanofibers (HMHNFs) composed of TiO ₂ /polyelectrolyte (PE) have been prepared by a combination of a electrospinning method and layer-by-layer (LBL) technology. The results show that both the average diameter and the wall thickness of the HMHNFs can be well controlled by the template, as well as the number of coating layers. The dried morphology of the obtained HMHNFs is dependent on the inner deposited numbers of the polyelectrolyte layers. When compared with other nanostructured TiO ₂ materials, such as commercial TiO ₂ nanoparticles (P25, Degussa) and TiO ₂ films, the hollow TiO ₂ /PE hybrid nanofibers exhibited higher photocatalytic activities.     

The hybrid photocatalyst of TiO2–SiO2 thin film prepared from rice husk silica

The TiO₂–SiO₂ thin film was prepared by self-assembly method by mixing SiO₂ precursor with titanium precursor solution and aged to obtain a co-precipitation of silica and titanium crystals. Dip coating method was applied for thin film preparation on glass slide. The X-ray diffraction (XRD) of the self-assembly thin film had no characteristic property of SiO₂ and even anatase TiO₂ but indicated new crystal structure which was determined from the Fourier Transform Infrared Spectrophotometer (FTIR) as a hybridized Ti–O–Si bonding. The surface area and surface volume of the self-assembly sample were increased when SiO₂ was incorporated into the film. The self-assembly TiO₂–SiO₂ thin film exhibited the enhanced photocatalytic decolorization of methylene blue (MB) dye. The advantages of SiO₂ are; (1) to increase the adsorbability of the film and (2) to provide the hydroxyl radical to promote the photocatalytic reaction. The self-assembly thin film with the optimum molar ratio (SiO₂:TiO₂) as 20:80 gave the best performance for photocatalytic decolorization of MB dye with the overall efficiency of 81%.     

二氧化钛修饰的微结构聚合物光纤预制棒制备及其在光催化中应用的探索研究

首次用二氧化钛(TiO₂)纳米材料修饰的547孔微结构聚合物光纤(MPOF)二次预制棒作为阵列化微管式光催化反应器对亚甲基兰的光催化分解进行研究.将高光催化活性的P25型二氧化钛纳米粒子均匀分散在TiO₂溶胶中,对547孔微结构聚合物光纤孔洞内壁进行铺膜,得到了负载光催化剂的阵列化微管材料.该TiO₂MPOF有序复合的阵列化微管不仅对二氧化钛纳米粒子起到负载作用,还可以作为光波导介质(rolling-up薄膜波导,聚光、导光进入二氧化钛薄膜层)、污染物反应流体通道.以有机染料亚甲基兰为模拟污染物,研究了TiO₂负载量、亚甲基兰的初始浓度及溶液pH值等因素对光降解效果的影响.该反应器547个孔道的内表面用于负载光催化剂,不仅增加了固-液接触面积,也提高了光的吸收效率,从而提高了光催化效率.迄今为止,这种兼具导光、聚光、传质、负载功能于一体的光催化反应器还未见报道.     

Preparation of continuous TiO2 fibers by sol-gel method and its photocatalytic degradation on formaldehyde

The continuous TiO₂ fibers were prepared by sol-gel method using the tetrabutyl orthotitanate as the precursor. The sol-formation process is studied by FT-IR spectroscopy. The synthesized continuous TiO₂ fibers were characterized using SEM, HRTEM and XRD. Results demonstrate that the titanate sol has good spinnability when R ≤ 2 (R = H₂O:Ti(OC₄H₉)₄, molar ratio). The fibers have the length of several meters and the diameter of about 30 μm. The fibers are a radial close-packed product of nano-particles with high crystallinity. The continuous TiO₂ fibers are co-crystal including anatase phase and rutile phase. The formaldehyde degradation ratio of continuous TiO₂ fiber was 98.6%.     

Investigation of chemical decomposition of CCl4 on TiO2 near room temperature

Dissociative adsorption of CCl₄ on TiO₂ at 35 °C has been studied by Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and electron spin resonance. CCl₄ decompose to form CO, CO₂, and CO₃ on the surface, at such a low temperature, in which CO₂ formation is not from CO oxidation on TiO₂, but CO₃ can be produced by CO and CO₂ adsorption. The Cl generated from CCl₄ decomposition is left on the surface and bonded to titanium ions. Mineralization of CCl₄ on TiO₂ involves the lattice oxygens. Thermodynamical driving force and possible reaction routes for CO and CO₂ formation in the CCl₄ decomposition on TiO₂ are discussed.     

铈和磷钨酸共掺杂纳米二氧化钛中空纤维的制备及其光催化活性

以棉花纤维为模板,以钛酸四正丁酯、硝酸铈铵和磷钨酸为原料采用模板法制备了一系列铈和磷钨酸共掺杂的、具有中空纤维结构的TiO₂光催化材料, 利用扫描电子显微镜、X射线衍射、BET和紫外-可见光谱等技术对其形貌、晶体结构及表面结构、光吸收特性等进行了表征. 以苯酚溶液的光催化降解为模型反应,考察了不同掺杂量的样品在紫外和可见光下的光催化性能. 结果表明,用模板法制备的TiO₂纤维材料具有中空结构,共掺杂的TiO₂纤维在紫外和可见光条件下较纯TiO₂纤维和单掺杂TiO₂纤维对苯酚溶液具有更好的光催化降解效果, 且铈和磷钨酸的掺杂量显著影响该纤维材料的催化性能;当铈掺杂量为0.3mol%和磷钨酸掺杂量为2mol%,在500 oC焙烧2 h所得中空纤维材料的催化性能最佳,4 h即可使苯酚溶液的降解率达98.5%;重复使用4次仍可使苯酚溶液的降解率保持在87%以上,且该催化剂材料易于离心分离去除.     

Synthesis and photocatalytic properties of porous TiO2 films prepared by ODA/sol-gel method

Porous TiO₂ films were deposited on SiO₂ pre-coated glass-slides by sol-gel method using octadecylamine (ODA) as template. The amount of ODA in the sol played an important role on the physicochemical properties and photocatalytic performance of the TiO₂ films. The films prepared at different conditions were all composed of anatase titanium dioxide crystals, and TiO₂ crystalline size got larger with increasing ODA amount. The maximum specific surface area of 41.5 m²/g was obtained for TiO₂ powders prepared from titanium sol containing 2.0 g ODA. Methyl orange degradation rate was enhanced along with increasing ODA amount and reached the maximal value at 2.0 g addition of ODA. After 40 min of UV-light irradiation, methyl orange degradation rate reached 30.5% on the porous film, which was about 10% higher than that on the smooth film. Porous TiO₂ film showed almost constant activity with slight decrease from 30.5% to 28.5% after 4 times of recycles.     

Preparation and photoelectrochemical performance of Ag/graphene/TiO2 composite film

By dipping-lifting in sol-gel solution and reducing process, the graphene/TiO₂ composite film on the glass plate was first prepared. Then, the Ag/graphene/TiO₂ composite film was fabricated by interface reaction with AgNO₃ and N₂H₄·H₂O on the surface of graphene/TiO₂ composite film. The characterization results show that the uniform porous TiO₂ film is made up of the anatase crystal, and the Ag/graphene/TiO₂ composite film is constructed by doping or depositing graphene sheets and Ag nanoparticles on the surface of TiO₂ film. The photoelectrochemical measurement results indicate that the Ag/graphene/TiO₂ composite film has an excellent photoelectrochemical conversion property.     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Photosensitization of nanocrystalline TiO2 film electrode with cadmium sulphoselenide

Nanocrystalline titanium dioxide (TiO₂) thin films composed of densely packed nanometer-sized grains have been successfully deposited onto an indium-doped-tin oxide (ITO) substrate. Then cadmium sulphoselenide (CdSSe) thin film was deposited onto pre-deposited TiO₂ to form a TiO₂/CdSSe film, at low temperature using a simple and inexpensive chemical method. The X-ray diffraction, selected area electron diffraction, scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and water contact angle techniques were used for film characterization. Purely rutile phase of TiO₂ with super-hydrophilic and densely packed nanometer-sized spherical grains of approximate diameter 30-40 (±2) nm was observed. The increase in optical absorption was observed after CdSSe film deposition. Nest like surface morphology of CdSSe on TiO₂ surface results in air trapping in the crevices which prevents water from adhering to the film with increase in water contact angle. Photosensitization of TiO₂ with CdSSe was confirmed with light illumination intensity of 80 mW/cm².     

Magnetic resonance imaging on CO(2) miscible and immiscible displacement in oil-saturated glass beads pack

In this study, the displacement processes were observed as gaseous or supercritical CO₂ was injected into n-decane-saturated glass beads packs using a 400-MHz magnetic resonance imaging (MRI) system. Two-dimensional images of oil distribution in the vertical median section were obtained using a spin-echo pulse sequence. Gas channeling and viscous fingering appeared obviously in immiscible gaseous CO₂ displacement. A piston-like displacement front was detected in miscible supercritical CO₂ displacement that provided high sweep efficiency. MRI images were processed with image intensity analysis methods to obtain the saturation profiles. Final oil residual saturations and displacement coefficients were also estimated using this imaging intensity analysis. It was proved that miscible displacement can enhance the efficiency of CO₂ displacement notably. Finally, a special coreflood analysis method was applied to estimate the effects of capillary, viscosity and buoyancy based on the obtained saturation data.     

Mechanism of enhanced photocatalysis of TiO2 by Fe in suspensions

In this work, the mechanism of enhanced photocatalysis of TiO₂ with Fe³⁺ was studied using Sulfadiazine (SD) as the model compound. Results indicated that degradation rate of SD was enhanced by the addition of Fe³⁺ in TiO₂ suspension. The crystalline structure of TiO₂ particles was stable in suspensions. The hydroxyl radical generated by TiO₂/Fe³⁺ (both TiO₂ and Fe³⁺) photocatalysis was in a higher yield. Moreover, Fe²⁺ was found not to give an obvious impact on the SD degradation in TiO₂ suspension, whereas Fe³⁺ had a notable effect. The adsorption amount of TiO₂ was greatly enhanced by the addition of Fe³⁺ in suspensions. Finally, an interaction model of SD degradation in TiO₂ suspension containing Fe³⁺ was also proposed by investigating of surface behaviors of TiO₂ particles. It will be beneficial to use Fe³⁺ as the electron acceptors on the surface of TiO₂ particles, which helps to improve the yield of hydroxyl radical.     

Cobalt-doped TiO2: a computational analysis of dopant placement and charge transfer direction on thin film anatase

ABSTRACT

Titanium dioxide (TiO₂) nanocrystals are promising materials for photo-electrochemical water splitting. This study focuses on how surface dopant placement can affect the electronic properties. TiO₂ anatase thin films are doped two ways: a cobalt ion replacing a surface titanium ion (surface ingrained) and a cobalt ion chemisorbed to two surface oxygen ions and two NH₃ ligands. Specifically, when studying the binding pattern, the cobalt ion dopant changes from an electron acceptor for the surface ingrained model to an electron donor for the chemisorbed model. The optical absorption peaks of the surface ingrained model are attributed to p→d transitions and are much stronger when compared to the d→d transitions for the chemisorbed model. It is the conclusion of this computational study that one can alter the cobalt dopant on the anatase thin film to focus a positive or negative charge at the surface by changing the surface dopant location.     

Growth of branched rutile TiO2 nanorod arrays on F-doped tin oxide substrate

Branched rutile TiO₂ nanorod arrays were directly synthesized on the F-doped tin oxide (FTO) substrate through a two-step hydrothermal treatment by a seeding method with TiO₂-nanorods as seeds. The samples were characterized respectively by means of X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and field-emission scanning electron microscopy (FESEM). Results showed that TiO₂ nanorods with nanobranches (TiO₂-NB) grew vertically on the FTO substrate. XRD and HRTEM results confirmed that the TiO₂-NB arrays were single-crystalline rutile. The optical properties of the samples were studied with a UV-vis spectrometer. The photocatalytic activity of the TiO₂-NB film is better than that of P25 particulate film. Direct electrical pathway and improved light-harvesting efficiency were crucial for the superior photocatalytic activity of the TiO₂-NB arrays.     

Super-hydrophilic properties of TiO2-DLC nanocomposite films fabricated by the simple electrochemical process

Anatase TiO₂ nanoparticles incorporated DLC films were successfully deposited on single crystalline silicon substrates by the electrolysis of TiO₂-methanol solution under ambient atmospheric pressure and low temperature. Anatase TiO₂ nanoparticles were embedded into amorphous carbon matrix, forming the typical nanocrystalline/amorphous nanocomposite films, confirmed by transmission electron microscopy (TEM). TiO₂ incorporation effectively increased the sp³-hybridized carbon concentration in the composite film, and further regulated the microstructure and surface morphology. Furthermore, the static contact testing completely displayed, TiO₂ incorporation got the composite films super-hydrophilic, which fundamentally improved the wetting ability of DLC film.     

Morphology and natural wettability properties of sol-gel derived TiO2-SiO2 composite thin films

Previous studies suggest that granular interfaces induce a natural and persistent super-hydrophilicity in TiO₂-SiO₂ composite thin films deposited by sol-gel route. This effect enables to consider self-cleaning applications that do not require a permanent UV exposure, whereas such a permanent exposure is necessary for pure TiO₂ films. In this study, TiO₂-SiO₂ composite thin films have been deposited from a TiO₂ anatase crystalline suspension and different SiO₂ polymeric sols. Wettability studies show that a suitable control of the TiO₂-SiO₂ mixed sol formulations noticeably enhances persistence of the natural super-hydrophilicity in composite films. It is shown that, beside granular interface effects, modifications in the composite film morphologies can noticeably influence wettability properties.     

Preparation of NaYF4:,Er3+/TiO2 composite and up-conversion luminescence properties under visible light excitation

The up-conversion luminescence composite NaYF 4:Er 3+ /TiO 2 is prepared using the sol-gel method.The specimen has good crystallinity and two shapes,i.e.,viereck and round,while the sizes of viereck and round particles are both micron-sized.The TiO 2 has an anatase structure,while the NaYF 4 has a hexagonal phase,which can be hardly obtained through the common sol-gel method.Due to the big particle size and the high crystallinity of pure NaYF 4:Er 3+,the composite has a small specific surface area that is less than Degussa P25 TiO 2.The NaYF 4:Er 3+ /TiO 2 composite shows several emission peaks at 211,237,and 251 nm under the excitation of 388 nm,at 395 nm and 411 nm under the excitation of 500 nm,and at 467,481,492,and 508 nm under the excitation of 570 nm.     

Influence of Ti nanocrystallization on microstructure, interface bonding, surface energy and blood compatibility of surface TiO2 films

Recent progress in ultrafine-grained/nano-grained (UFG/NG) titanium permits a consideration for TiO₂ films deposited on nano-grained titanium for antithrombogenic application such as artificial valves and stents. For this paper, the microstructure, interface bonding, surface energy, and blood compatibility features of TiO₂ films deposited by direct current magnetron reactive sputtering technology on NG titanium and coarse-grained (CG) titanium were investigated. The results show that the nanocrystallization of titanium substrate has a significant influence on TiO₂ films. At the same deposition parameters, the content of rutile phase of TiO₂ film was increased from 47% (on the CG titanium substrate) to 72% (on the NG titanium substrate); the adhesion of TiO₂ film was improved from 5.8 N to 17 N; the surface energy was reduced from 6.37 dyn/cm to 3.01 dyn/cm; the clotting time was improved from 18 min to 28 min; the platelets accumulation and pseudopodium of adherent platelets on TiO₂ film on NG titanium were considerably reduced compared to that on CG titanium. The present results demonstrate the possibility of improving the blood compatibility of TiO₂ film through the approach of substrate nanocrystallization. Also it may provide an attractive idea to prepare stents with biological coatings of more outstanding blood compatibility and interface bonding.