Electron scattering mechanisms in indium-tin-oxide thin films prepared at the various process conditions

The carrier concentrations and mobilities of indium-tin-oxide (ITO) thin films by DC magnetron sputtering at the various process conditions were measured by means of the Hall technique. The relationship between the carrier concentration and mobility showed two distinct features: (i) roughly up to the carrier concentration of 9.0 × 10²⁰/cm³, both the carrier concentration and mobility increased together; (ii) above the carrier concentration of 9.0 × 10²⁰/cm³, the carrier mobility decreased as the carrier concentration further increased. The distinct behavior of the carrier concentration and mobility was due to the transition of the dominant electron scattering mechanism. ITO thin film with a low degree of crystallinity was governed by the grain boundary scattering. However, the ionized impurity scattering was dominant in ITO thin film with a high carrier concentration over 9.0 × 10²⁰/cm³. The overall characterizations related to the carrier concentration and mobility were also performed using X-ray diffractometer, UV-vis-NIR spectrometer, scanning electron microscope, atomic force microscope.     

Optimum packing density and crystal structure of tin-doped indium oxide thin films for high-temperature annealing processes

The influence of high-temperature annealing on the electrical properties and microstructure of tin-doped indium oxide (ITO) thin films was investigated as a function of oxygen gas flow ratio to argon gas during the sputtering deposition. The ITO thin films were annealed at 500 °C in air after the deposition. It was found that the ITO thin films, which were deposited in relatively low oxygen gas flow ratio, exhibited high Hall mobility and low-resistivity after the annealing. Furthermore, the X-ray reflectivity and diffraction measurement revealed that the ITO thin film with low-resistivity after annealing exhibited high packing density, smooth surface and low crystallization degree. It can be considered that the carrier electron scattering was suppressed with increasing in the packing density of the ITO thin film; as a result, the Hall mobility and resistivity were improved.     

铟锡氧化物薄膜表面等离子体损耗降低的研究

本文采用直流磁控溅射方法在普通浮法玻璃基底上制备了立方多晶铁锰矿结构的铟锡氧化物(indium tin oxide, ITO)薄膜,并对其进行了结晶性、表面粗糙度、紫外-可见吸收光谱、折射率、介电常数及霍尔效应的测试.研究了溅射时基底温度的改变对于ITO薄膜的光电、表面等离子体性质的影响.随着基底温度由100?C升高至500?C,其光学带隙(3.64—3.97eV)展宽,减少了电子带间跃迁的概率,有效降低了ITO薄膜的光学损耗.与此同时,对应ITO薄膜的载流子浓度(4.1×10~(20)-—2.48×10~(21)cm~(-3))与迁移率(24.6—32.2 cm~2·V~(-1)·s~(-1))得到提高,电学损耗明显降低.     

Electrical and structural properties of In-doped ZnO films deposited by RF superimposed DC magnetron sputtering system

Zinc-indium-oxide (ZIO) films were deposited on non-alkali glass substrates by RF superimposed DC magnetron sputtering with a ZIO (9.54 wt% In₂O₃ content) high-density, sintered target at room temperature. The electrical, structural and optical properties of the ZIO films deposited with different sputtering parameters were examined. The total power for RF superimposed DC magnetron sputtering was 80 W. The RF power ratio in the total sputtering power was changed from 0 to 100% in steps of 25%. The ZIO films deposited with a 100% RF discharge showed the lowest resistivity, 1.28×10⁻³ Ω cm, due to the higher carrier concentration. The ZIO film deposited at 50% RF power showed a relatively larger grain size and smaller FWHM. XPS suggested an increase in the level of In³⁺ substitution for Zn²⁺ in the ZnO lattice with increasing RF/(DC+RF) due to the low damage process. The average transmittance of all ZIO films in the visible light region was >80%. The increasing RF power portion of the total sputtering power led to a broadening of the optical band gap, which was attributed to the increase in carrier density according to Burstein-Moss shift theory.     

用于彩色滤光片的低阻低应力ITO透明导电膜

探讨了用于彩色滤光片的低电阻和低压应力的ITO透明导电膜工艺。用磁控溅射方法在不同温度的衬底上制备了ITO薄膜。研究了膜形衬底温度与膜结晶化程度的关系,以及膜形衬底温度对膜电阻和压应力的影响。对不同衬底温度下形成的ITO薄膜进行了退火处理,并对退火后的ITO薄膜的电阻和压应力特性进行了分析。结果表明,采用室温沉积非晶态ITO膜,在真空退火下可获得低电阻、低压应力的多晶相ITO膜。     

Growth of transparent conducting nano-structured In doped ZnO thin films by pulsed DC magnetron sputtering

Transparent conducting nano-structured In doped zinc oxide (IZO) thin films are deposited on corning 7059 glass substrates by bipolar pulsed DC magnetron sputtering with variation of pulsed frequency and substrate temperature. Highly c-axis oriented IZO thin films were grown in perpendicular to the substrate on the 30 kHz and 500 °C. The IZO films exhibited surface roughness of 3.6 nm similar to the commercial ITO and n-type semiconducting properties with electrical resistivity (carrier mobility) of about 5 × 10⁻³ Ω cm (14 cm²/V s). The optical characterization showed high transmittance of over 85% in the UV-vis region and exhibited the absorption edge of near 350 nm. In micro-Raman spectra, the origin of two additional modes is attributed to the host lattice defect due to the addition of In dopant. These results suggest that the IZO film can possibly be applied to make transparent conducting electrodes for flat panel displays.     

Investigation of diffusion and crystallization processes in thin ITO films by temperature and time resolved grazing incidence X-ray diffractometry

Oxygen diffusion into metallic In/Sn films and crystallite growth of thin indium tin oxide (ITO) films were investigated by in situ high temperature grazing incidence X-ray diffractometry (HT-GIXRD) at temperatures ranging from 100 to 300 °C. The investigated films were deposited by dc magnetron sputtering from a metallic target at different oxygen flows and bias voltages. The deposition process influences not only the film properties but also the film reactions during the post-deposition annealing process.

The ITO formation is determined by two processes: the diffusion of oxygen into the metallic grains and a fast crystallization process. Kinetic parameters for both processes were derived. A model was developed which allows the determination of the diffusion coefficient D from the time dependence of the integral intensity of the ITO X-ray reflection. Diffusion coefficients as well as the activation energies are influenced by the bias voltage but not by the oxygen flow.

According to the Johnson–Mehl–Avrami theory, the crystallization can be described as a two-dimensional process.     

Effect of the duty ratio on the indium tin oxide (ITO) film deposited by in-line pulsed DC magnetron sputtering method for resistive touch panel

The indium tin oxide (ITO) film was deposited on PET (polyethylene terephthalate) film using in-line pulsed DC magnetron sputtering system with different duty ratios. The reverse time and the frequency of pulsed DC power were changed to obtain the different duty ratios. From the electrical and optical properties such as the sheet resistance, resistivity, thickness and transmittance, the pulsed DC sputtered ITO/PET films were also superior to the DC sputtered ITO/PET films. The reverse time had little effect on the properties of the ITO/PET film and the frequency of pulsed DC power had an immerse effect on the properties of the ITO/PET films. The optimal ITO/PET film was obtained when the frequency was 200 kHz, the reverse time was 1 μs, and the duty ratio was about 80%.     

直流磁控反应溅射法制备的钒氧化物薄膜及其光谱研究

用直流磁控反应溅射法和不同基底温度下在玻璃底上沉积微纳结构的氧化钒薄膜,通过X射线衍射、电子扫描显微镜、UV-Vis透射、红外和拉曼光谱研究了薄膜的结构特性.在低温下制备的薄膜表现出高的光学透过特性,在基底温度低于200℃下制备的薄膜具有无定形结构,而在基底温度高于200℃时制备的薄膜具有多晶结构.薄膜的光学参数使用经...     

The effect of electro-annealing on the electrical properties of ITO film on colorless polyimide substrate

The effect of different annealing methods on the sheet resistance of indium tin oxide (ITO) on polyimide (PI) substrate has been investigated. ITO thin films were prepared by RF magnetron sputtering in pure Ar gas and electro-annealing, this was carried out in the flow of an electric current at several temperatures between 100 and 180 °C in air. Electro- and thermal annealing were compared in order to confirm differences between the electrical, optical and microstructural properties of the ITO thin films. As electro-annealing induced the predominant growth of crystallites of ITO thin films along (4 0 0) plane, the sheet resistance of ITO films that were electro-annealed for 2 mA at 180 °C considerably decreased from 50 to 28 Ω/cm².     

Development of conductive transparent indium tin oxide (ITO) thin films deposited by direct current (DC) magnetron sputtering for photon-STM applications

Highly conductive and transparent indium tin oxide (ITO) thin films, each with a thickness of 100 nm, were deposited on glass and Si(100) by direct current (DC) magnetron sputtering under an argon (Ar) atmosphere using an ITO target composed of 95% indium oxide and 5% tin oxide for photon-STM use. X-ray diffraction, STM observations, resistivity and transmission measurements were carried out to study the formation of the films at substrate temperatures between 40 and 400 °C and the effects of thermal annealing in air between 200 and 400 °C for between1 and 5 h. The film properties were highly dependent on deposition conditions and on post-deposition film treatment. The films deposited under an Ar atmosphere pressure of ∼1.7×10^-3 Torr by DC power sputtering (100 W) at substrate temperatures between 40 and 400 °C exhibited resistivities in the range 3.0–5.7×10^-5 Ω m and transmissions in the range 71–79%. After deposition and annealing in air at 300 °C for 1 h, the films showed resistivities in the range 2.9–4.0×10^-5 Ω m and transmissions in the range 78–81%. Resistivity and transmission measurements showed that in order to improve conductive and transparent properties, 2 h annealing in air at 300 °C was necessary. X-ray diffraction data supported the experimental measurements of resistivity and transmission on the studies of annealing time. The surface roughness and film uniformity improve with increasing substrate temperature. STM observations found the ITO films deposited at a substrate temperature of 325 °C, and up to 400 °C, had domains with crystalline structures. After deposition and annealing in air at 300 °C for 1 h the films still exhibited similar domains. However, after deposition at substrate temperatures from 40 °C to 300 °C, and annealing in air at 300 °C for 1 h, the films were shown to be amorphous. More importantly, the STM studies found that the ITO film surfaces were most likely to break after deposition at a substrate temperature of 325 °C and annealing in air at 300 °C for 2 or 3 h. Such findings give some inspiration to us in interpreting the effects of annealing on the improvement of conductive and transparent properties and on the transition of phases. In addition, correlations between the conductive/transparent properties and the phase transition, the annealing time and the phase transition, and the conductive/transparent properties and the annealing time have been investigated. Received: 10 July 2000 / Accepted: 27 October 2000 / Published online: 9 February 2001     

Highly transparent and conductive indium tin oxide thin films for solar cells grown by reactive thermal evaporation at low temperature

Transparent conductive tin-doped indium oxide (In₂O₃:Sn, ITO) thin films with various Sn-doping concentrations have been prepared using the low cost reactive thermal evaporation (RTE) technique at a low growth temperature of ~160 °C. The structural characteristics, optical and electrical properties of the ITO thin films were investigated. These polycrystalline ITO films exhibited preferential orientation along (222) plane and possessed low resistivities ranging from 3.51 to 5.71 × 10^?4 Ω cm. The decreased mobility was attributed to the scattering by ionized and neutral impurities at high doping concentrations. The optimized ITO thin film deposited with 6.0 wt% Sn-doping concentration exhibited a high average transparency of 87 % in the wavelength range of 380–900 nm and a low resistivity of 3.74 × 10^?4 Ω cm with a high Hall mobility of 47 cm² V^?1s^?1. A hydrogenated amorphous silicon and silicon–germanium (a-Si:H/a-SiGe:H) double-junction solar cell fabricated with the RTE-grown ITO electrodes presented a conversion efficiency of 10.51 %.     

ITO/Au/ITO multilayer thin films for transparent conducting electrode applications

Transparent and conducting ITO/Au/ITO multilayered films were deposited without intentional substrate heating on polycarbonate (PC) substrate using a magnetron sputtering process. The thickness of ITO, Au and ITO metal films in the multilayered structure was constant at 50, 10 and 40 nm, respectively.Although the substrate temperature was kept constant at 70 °C, ITO/Au/ITO films were polycrystalline with an (1 1 0) X-ray diffraction peak, while single ITO films were amorphous. Surface roughness analysis indicated ITO films had a higher average roughness of 1.76 nm, than the ITO/Au/ITO film roughness of 0.51 nm. The optoelectrical properties of the ITO/Au/ITO films were dependent on the Au thin film, which affected the ITO film crystallinity. ITO/Au/ITO films on PC substrates were developed with a resistivity as low as 5.6 × 10⁻⁵ Ω cm and a high optical transmittance of 71.7%.     

Indium tin oxide thin films by bias magnetron rf sputtering for heterojunction solar cells application

In this investigation ITO thin films were prepared by bias magnetron rf sputtering technique at substrate temperature of 180 °C and low substrate-target distance for future a-Si:H/c-Si heterojunction (HJ) solar cells application. Microstructure, surface morphology, electrical and optical properties of these films were characterized and analyzed. The effects of ion bombardments on growing ITO films are well discussed. XRD analysis revealed a change in preferential orientation of polycrystalline structure from (2 2 2) to (4 0 0) plane with the increase of negative bias voltage. Textured surface were observed on AFM graphs of samples prepared at high negative bias. Hall measurements showed that the carrier density and Hall mobility of these ITO films are sensitive to the bias voltage applied. We attributed these effects to the sensitivity of energy of Ar⁺ ions bombarding on growing films to the applied bias voltage in our experiments. At last the figure of merit was calculated to evaluate the quality of ITO thin films, the results of which show that sample prepared at bias voltage of −75 V is good to be used in HJ cells application.     

Thickness dependence of electrical properties of ITO film deposited on a plastic substrate by RF magnetron sputtering

Indium tin oxide (ITO) films with various thicknesses in range of 40-280 nm were prepared onto a plastic substrate (PMMA). Deposition was carried out with RF magnetron sputtering method and the substrate temperature was held at ∼70 °C, in lack of the thermal damage to the polymer substrate. Changes in microstructure and electrical properties of ITO films according to their thicknesses were investigated. It was found that amorphous layer with thickness of 80 nm was formed at the interface on the polymer substrate and polycrystalline ITO could be obtained above the thickness. Conductivity of ITO films was found to be strongly dependent on the crystallinity. Consequently, it is suggested that crystallinity of the deposited films should be enhanced at the initial stage of deposition and the thickness of amorphous region be reduced in order to prepare high quality ITO thin films on polymer substrates.     

两种方法制备ITO薄膜的红外特性分析

比较了用电束加热蒸发法和直流磁控溅射法制备的氧化锡铟(ITO)薄膜在红外波段的光学特性实验发现,通过直流磁控溅射在常温下制备的ITO薄膜在红外波段折射率稳定、消光系数小,比电子束加热蒸发制备的膜有较高的透过率在波长1550nm附近的透过率可达86%以上,消光系数约为004,方电阻最低为100Ω/□.     

金属有机物化学气相沉积生长GaN薄膜的室温热电特性研究

采用金属有机物化学气相沉积技术生长了不同掺杂浓度的GaN薄膜, 并且通过霍尔效应测试和塞贝克效应测试, 表征了室温下GaN薄膜的载流子浓度、迁移率和塞贝克系数. 在实验测试的基础上, 计算了GaN薄膜的热电功率因子, 并且结合理论热导率确定了室温条件下GaN薄膜的热电优值(ZT). 研究结果表明: GaN薄膜的迁移率随着载流子浓度的增加而减小, 电导率随着载流子浓度的增加而增加; GaN 薄膜材料的塞贝克系数随载流子浓度的增加而降低, 其数量级在100–500 μV/K范围内; GaN薄膜材料在载流子浓度为1.60×10¹⁸ cm^-3时, 热电功率因子出现极大值4.72×10^-4 W/mK²; 由于Si杂质浓度的增加, 增强了GaN薄膜中的声子散射, 使得GaN薄膜的热导率随着载流子浓度的增加而降低. GaN薄膜的载流子浓度为1.60×10¹⁸ cm^-3时, 室温ZT达到极大值0.0025.     

DC conduction processes and electrical parameters of the organic semiconducting zinc phthalocyanine, ZnPc, thin films

Electronic conduction in thermally evaporated thin films of organic semiconductor zinc phthalocyanine (ZnPc) has been investigated in a broad temperature range using gold Ohmic contacts. Electronic conduction by charge carrier hopping was dominated at low temperatures and for all applied voltages. At higher temperatures and at voltages just below 2 V conduction was found to obey Ohm's law, while at higher voltages space-charge-limited conduction (SCLC) was the dominated mechanism, which was controlled by hole-trapping states distributed exponentially within the band gap.In freshly prepared samples adsorbed oxygen was responsible for lower hole mobility and higher charge carrier concentrations. Prolonged heating of ZnPc films at 425 K resulted in lower defect state density, and thus reduced trap concentration and higher charge carrier mobility.     

Growth characteristics and properties of ZnO:Ga thin films prepared by pulsed DC magnetron sputtering

Transparent conductive ZnO:Ga thin films were deposited on Corning 1737 glass substrate by pulsed direct current (DC) magnetron sputtering. The effects of process parameters, namely pulse frequency and film thickness on the structural and optoelectronic properties of ZnO:Ga thin films are evaluated. It shows that highly c-axis (0 0 2) oriented polycrystalline films with good visible transparency and electrical conductivity were prepared at a pulsed frequency of 10 kHz. Increasing the film thickness also enlarged the grain size and carrier mobility which will subsequently lead to the decrease in resistivity. In summary, ZnO:Ga thin film with the lowest electrical resistivity of 2.01 × 10⁻⁴ Ω cm was obtained at a pulse frequency of 10 kHz with 500 nm in thickness. The surface RMS (root mean square) roughness of the film is 2.9 nm with visible transmittance around 86% and optical band gap of 3.83 eV.     

Comparative study of annealing and gold dopant effect on DC sputtered vanadium oxide films for bolometer applications

Vanadium oxide (VO_x) thin film has been widely used for IR detectors and it is one of the promising materials for THz detectors due to its high temperature coefficient of resistance (TCR) values. VO_x films with proper TCR values have also high resistance and it restricts bolometer performance especially for uncooled bolometers. To overcome this problem, deposition at elevated temperatures or annealing approach has been accepted and used but gold co-deposition approach has been proposed recently. In this study, vanadium oxide films were fabricated on high resistivity silicon substrates by reactive direct current magnetron sputtering in different O₂/Ar atmosphere at room temperature. We investigated influence of oxygen partial pressure during deposition process and fabricated VO_x thin films with sufficient TCR values for bolometer applications. In order to decrease resistivity of the deposited films, post annealing and gold doping approaches were performed separately. Effect of both post annealing process and gold doping process on structural and electrical properties of VO_x thin films deposited at room temperature were investigated and detailed comparison between these methods were presented. We obtained the best possible approach to obtain optimum conditions for the highly reproducible VO_x thin films which have the best resistivity and suitable TCR value for bolometer applications.