共查询到19条相似文献,搜索用时 515 毫秒
1.
《中国物理C(英文版)》2017,(2)
The BaF_2 (barium fluoride) spectrometer is one of the experiment facilities at the CSNS-WNS(White Neutron Source at China Spallation Neutron Source), currently under construction. It is designed to precisely measure the(n, γ) cross section, with 92 crystal elements and complete 4π steradian coverage. In order to improve the precision of measurement, in this paper, a new precise digitization and readout method is proposed. Waveform digitizing with 1 GSps sampling rate and 12-bit resolution is used to precisely capture the detector signal. To solve the problem of massive data readout and processing, the readout electronics is designed as a distributed architecture with 4 PXIe crates. The digitized signal is concentrated to the PXIe crate controller through a PCIe bus on the backplane and transmitted to the data acquisition system over gigabit Ethernet in parallel. Besides, the clock and trigger can be fanned out synchronously to every electronic channel over a high-precision distribution network. Test results show that the prototype of the readout electronics can achieve good performance and meet the requirements of the CSNS-WNS BaF_2 spectrometer. 相似文献
2.
With increasing physical event rates and the number of electronic channels, traditional readout schemes meet the challenge of improving readout speed caused by the limited bandwidth of the crate backplane. In this paper, a high-speed data readout method based on the Ethernet is presented to make each readout module capable of transmitting data to the DAQ. Features of explicitly parallel data transmitting and distributed network architecture give the readout system the advantage of adapting varying requirements of particle physics experiments. Furthermore, to guarantee the readout performance and flexibility, a standalone embedded CPU system is utilized for network protocol stack processing. To receive the customized data format and protocol from front-end electronics, a field programmable gate array (FPGA) is used for logic reconfiguration. To optimize the interface and to improve the data throughput between CPU and FPGA, a sophisticated method based on SRAM is presented in this paper. For the purpose of evaluating this high-speed readout method, a simplified readout module is designed and implemented. Test results show that this module can support up to 70 Mbps data throughput from the readout module to DAQ. 相似文献
3.
中国散裂中子源( CSNS ) 的建造对中子探测器提出了非常高的要求,如更大的有效面积、二维位置灵敏、高计数率、高探测效率和低的 灵敏度等。与传统的模拟读出方法相比,数字法读出具有更高的计数率, 更小的数据传输量,更简单的电子学设计以及更高的信噪比。对数字法读出进行了理论计算,利用GEM探测器的原始数据分析了数字法读出的位置分辨率与读出条宽度的关系。结果表明,数字法读出对于位置分辨要求较低( 小于4 mm) 的大面积位置灵敏探测器是一种较好的选择,如CSNS 小角谱仪探测器。Efficient thermal neutron detectors with large area, two-dimensional position sensitive, high counting rate high detection efficiency and low gamma sensitivity are required to satisfy the demands for the China Spallation Neutron Source (CSNS). Compared with the traditional analog readout method, the digital readout method has the advantages of higher counting rate, smaller quantity of data transmission, simpler readout system and higher signal to noise ratio. The theoretical analysis of the digital readout method is reported in this paper. Used the raw data of GEM detector, the relationship between the position resolution and the width of the readout strip was studied. The results indicate that the digital readout method could be a good choice for the large area position sensitive detector where the requirement of position resolution is less than 4 mm, e.g. the detector of Small-Angle Neutron Scattering (SANS) diffractometer of CSNS. 相似文献
4.
《中国物理C(英文版)》2017,(1)
A BaF_2(Barium Fluoride) detector array is designed to precisely measure the(n, γ) cross section at the CSNS-WNS(white neutron source at China Spallation Neutron Source). It is a 4π solid angle-shaped detector array consisting of 92 BaF_2 crystal elements. To discriminate signals from the BaF_2 detector, a pulse shape discrimination method is used, supported by a waveform digitization technique. There are 92 channels for digitizing. The precision and synchronization of clock distribution restricts the performance of waveform digitizing. In this paper, a clock prototype for the BaF_2 readout electronics at CSNS-WNS is introduced. It is based on the PXIe platform and has a twin-stage tree topology. In the first stage, clock is synchronously distributed from the tree root to each PXIe crate through a coaxial cable over a long distance, while in the second stage, the clock is further distributed to each electronic module through a PXIe dedicated differential star bus. With the help of this topology, each tree node can fan out up to 20 clocks with 3U size. Test results show the clock jitter is less than 20 ps, which meets the requirements of the BaF_2 readout electronics. Besides, this clock system has the advantages of high density, simplicity, scalability and cost saving, so it can be useful for other clock distribution applications. 相似文献
5.
The prototype of a time digitizing system for the BESⅢ endcap TOF (ETOF) upgrade is introduced in this paper. The ETOF readout electronics has a distributed architecture. Hit signals from the multi-gap resistive plate chamber (MRPC) are signaled as LVDS by front-end electronics (FEE) and are then sent to the back-end time digitizing system via long shield differential twisted pair cables. The ETOF digitizing system consists of two VME crates, each of which contains modules for time digitization, clock, trigger, fast control, etc. The time digitizing module (TDIG) of this prototype can support up to 72 electrical channels for hit information measurement. The fast control (FCTL) module can operate in barrel or endcap mode. The barrel FCTL fans out fast control signals from the trigger system to the endcap FCTLs, merges data from the endcaps and then transfers to the trigger system. Without modifying the barrel TOF (BTOF) structure, this time digitizing architecture benefits from improved ETOF performance without degrading the BTOF performance. Lab experiments show that the time resolution of this digitizing system can be lower than 20 ps, and the data throughput to the DAQ can be about 92 Mbps. Beam experiments show that the total time resolution can be lower than 45 ps. 相似文献
6.
Aiming at the application requirements of information optics,this Letter proposed a perovskite quantum dot random lasing pumping method suitable for high-speed modulation.At the same time,the luminescence characteristics of perovskite quantum dot films under electron beam pumping conditions are analyzed,and the random lasing mechanism of electron beam pumping CsPbBr3 quantum dot films is revealed.Finally,it is confirmed that perovskite quantum dots are easy to realize random lasing under electron beam pumping conditions. 相似文献
7.
《中国物理C(英文版)》2017,(1)
It is proposed to upgrade the endcap time-of-flight(ETOF) of the Beijing Spectrometer Ⅲ(BESⅢ) with a multi-gap resistive plate chamber(MRPC), aiming at an overall time resolution of about 80 ps. After completing the entire readout electronics system, some experiments, such as heat radiation, radiation hardness and large-current beam tests, have been carried out to confirm the reliability and stability of the readout electronics. An on-detector test of the readout electronics has also been performed with the beam at the BEPCⅡ E3 line. The test results indicate that the readout electronics system fulfills its design requirements. 相似文献
8.
The optical chaotic communication system using open-loop fiber transmission is studied under strong injection conditions. The optical chaotic communication system with open-loop configuration is studied using fiber transmission under strong injection conditions. The performances of fiber links composed of two types of fiber segments in different dispersion compensation maps are compared by testing the quality of the recovered message with different bit rates and encrypted by chaotic modulation (CM) or chaotic shift keying (CSK). The result indicates that the performance of the pre-compensation map is always worst. Two types of symmetrical maps are identical whatever the encryption method and bit-rate of message are. For the transmitting and the recovering of message of lower bit rate (1 Gb/s), the post-compensation map is the best scheme. However, for the message of higher bit rate (2.5 Gb/s), the parameters in communication system need to be modified properly in order to adapt to the high-speed application. Meanwhile, two types of symmetrical maps are the best scheme. In addition, the CM method is superior to the CSK method for high-speed applications. It is in accordance with the result in a back-to-back configuration system. 相似文献
9.
An innovative multilevel read-only recording method is proposed. In this method, a short pit/land is deliberately inserted to the original land/pit. This modifies the wave-shape of readout signM. Taking the wave-shape as the symbol of level detection, a signal wave-shape modulation (SWSM) multilevel method is realized. This method is carried out and validated on the DVD read-only manufacture and readout system. A capacity of 15 GB can be expected, and a bit error rate of 10-4 is achieved. The capacity can meet the demand of high definition movie publication. This method also provides a potential multi-level solution for other storage formats and systems. 相似文献
10.
F.Ratnikov 《高能物理与核物理计算国际会议公报》2001,(1):294-295
The CDF collaboration at the Fermilab Tevatron analyses proton-antiproton interactions at a center-of=mass energy of 2 TeV.during the the collider run starting this year the experiment expects to record 1 Petabyte of data and associated data samples,The Data Handling(DH) system has online and offline components.The DH offline component provides access to the stored data,to stored reconstruction output,to stored Monte-Carlo data samples,and user owned data samples.It serves more than 450 physicists of the collaboration.The extra requirements to the offline component of the Data Handling system are simplicity and convenience for users.More than 50 million events of the CDF Run II data have been already processed using this system. 相似文献
11.
A new CMOS readout integrated circuit (ROIC) for microbolometric focal plane array (FPA) is proposed in this paper. By applying multiple-module parallel working technique, the pixel readout speed of the CMOS ROIC can reach 10 MHz, which is very suitable for large-scale microbolometer array. The CMOS ROIC of each parallel working module consists of three major parts: direct injection (DI) input circuits, column-shared integrating circuits, and common noise-suppressing circuits. The readout structure of the ROIC is simple because of the DI input, shared and common circuits, and this makes the ROIC satisfy the requirements of small-pixel microbolometric FPA. Furthermore, the voltage signals from different working modules can be output according to a certain order through a high-speed output circuit. An experimental readout chip based on the proposed ROIC has been designed and fabricated to verify its readout function and performance. The measurement results of the experimental readout chip have successfully proved that the proposed CMOS ROIC can be applied to high-speed, low-noise, large-scale and high-resolution microbolometric FPA. 相似文献
12.
为获取高帧频、大动态范围、低数据量的精确视觉信息,提出了一种基于地址-事件表达(AER)的实时视觉CMOS传感器实现方法。采用AER方式,多模式的行仲裁及实时时间标记,有效减小读出数据量,减小时域行间信息扭曲;利用像素级光强变化感知电路探测光强变化,双采样脉冲宽度调制(PWM)电路量化光强。仿真结果显示,在100lx光强下,获得最小等效帧频1000frame/s,10lx光强下为100frame/s,静态动态范围大于133dB,视频动态范围48.16dB,并可实现实时时间标记、多模式仲裁的功能,减小输出数据量11.61%~42.74%。结果表明,该方法可完成实时视觉信息的采集、处理、输出,适用于高速、高动态范围视觉领域。 相似文献
13.
14.
CAO Ping SUN Wei-Jia JI Xiao-Lu FAN Huan-Huan WANG Si-Yu LIU Shu-Bin AN Qi 《中国物理C(英文版)》2014,38(4):046101-046101
The prototype of a time digitizing system for the BESⅢ endcap TOF (ETOF) upgrade is introduced in this paper. The ETOF readout electronics has a distributed architecture. Hit signals from the multi-gap resistive plate chamber (MRPC) are signaled as LVDS by front-end electronics (FEE) and are then sent to the back-end time digitizing system via long shield differential twisted pair cables. The ETOF digitizing system consists of two VME crates, each of which contains modules for time digitization, clock, trigger, fast control, etc. The time digitizing module (TDIG) of this prototype can support up to 72 electrical channels for hit information measurement. The fast control (FCTL) module can operate in barrel or endcap mode. The barrel FCTL fans out fast control signals from the trigger system to the endcap FCTLs, merges data from the endcaps and then transfers to the trigger system. Without modifying the barrel TOF (BTOF) structure, this time digitizing architecture benefits from improved ETOF performance without degrading the BTOF performance. Lab experiments show that the time resolution of this digitizing system can be lower than 20 ps, and the data throughput to the DAQ can be about 92 Mbps. Beam experiments show that the total time resolution can be lower than 45 ps. 相似文献
15.
A data transmission method for particle physics experiments based on Ethernet physical layer 下载免费PDF全文
Due to its advantages of universality, flexibility and high performance, fast Ethernet is widely used in readout system design for modern particle physics experiments. However, Ethernet is usually used together with the TCP/IP protocol stack, which makes it difficult to implement readout systems because designers have to use the operating system to process this protocol. Furthermore, TCP/IP degrades the transmission efficiency and real-time performance. To maximize the performance of Ethernet in physics experiment applications, a data readout method based on the physical layer(PHY) is proposed. In this method, TCP/IP is replaced with a customized and simple protocol, which makes it easier to implement. On each readout module, data from the front-end electronics is first fed into an FPGA for protocol processing and then sent out to a PHY chip controlled by this FPGA for transmission.This kind of data path is fully implemented by hardware. From the side of the data acquisition system(DAQ),however, the absence of a standard protocol causes problems for the network related applications. To solve this problem, in the operating system kernel space, data received by the network interface card is redirected from the traditional flow to a specified memory space by a customized program. This memory space can easily be accessed by applications in user space. For the purpose of verification, a prototype system has been designed and implemented.Preliminary test results show that this method can meet the requirements of data transmission from the readout module to the DAQ with an efficient and simple manner. 相似文献
16.
《中国物理C(英文版)》2016,(8)
A scalable readout system(SRS) is designed to provide a general solution for different micro-pattern gas detectors in various applications.The system mainly consists of three kinds of modules:the ASIC card,the adapter card and the front-end card(FEC).The ASIC cards,mounted with particular ASIC chips,are designed for receiving detector signals.The adapter card is in charge of digitizing the output signals from several ASIC cards.The PEC,edged-mounted with the adapter,has field-programmable gate array(FPGA)-based reconfigurable logic and I/O interfaces,allowing users to choose different ASIC cards and adapters for different experiments,which expands the system to various applications.The FEC transfers data through Gigabit Ethernet protocol realized by a TCP processor(SiTCP) IP core in FPGA.By assembling a flexible number of FECs in parallel through Gigabit Ethernet,the readout system can be tailored to specific sizes to adapt to the experiment scales and readout requirements.In this paper,two kinds of multi-channel ASIC chip,VA140 and AGET,are applied to verify the scalability of this SRS architecture.Based on this VA140 or AGET SRS,one FEC covers 8 ASIC(VA140) cards handling 512 detector channels,or 4 ASIC(AGET) cards handling 256 detector channels,respectively.More FECs can be assembled in crates to handle thousands of detector channels. 相似文献
17.
18.
随着海洋探索和军事应用的迫切需求,水声通信需要向高数据率、高可靠性方向发展。正交频分复用技术被视为水声高速通信的新途径,并被成功应用于水声通信,在水声通信中展现了其优越性。高度灵活的自适应平台的发展,激发了可重编程水声调制解调器的发展,以适应不同实验/应用场景的需求。文中从带宽、调制方案、数据率、传输距离、误码率方面,介绍了国内外研究机构对可重编程正交频分复用水声调制解调器研究的进展,并对其中的技术进行概述。最后对可重编程正交频分复用水声调制解调器进行了展望。认为可重编程正交频分复用水声调制解调器需要的是分块接收处理的自适应实时扩展平台,同时也坚信水声网络的发展和需求必将推动智能水声通信的发展。 相似文献