大分子不饱和单体法合成具有核壳结构的丙烯酸酯/聚氨酯乳液及表征

采用丙烯酸酯（AC）对水性聚氨酯（WPU）进行改性,合成了接枝型丙烯酸酯/聚氨酯(PUA)复合乳液。 随着共聚物中丙烯酸酯质量分数的增加,乳液外观由透明变为不透明,乳液粒径随之增大、分布变宽。 TEM显示,PUA乳胶粒子呈现清晰的核壳结构,且形态规整,粒径分布在60~120 nm之间。 FTIR测试表明,随着丙烯酸酯质量分数的增加,聚氨酯(PU)硬段氢键化作用先增强后减弱,硬段的有序度逐渐降低。 DSC分析表明,当AC的质量分数低于75%时,PU、聚丙烯酸酯(PA)两组分相容性较好,只出现一个玻璃化转变温度,并且随着PA质量分数的增加逐渐升高。 PA质量分数的增加,使胶膜的最大热失重速率从363 ℃提高至412 ℃,吸水率从11.3%降低至5.7%,弹性模量从16.4 MPa提高至47.6 MPa,拉伸强度从9.0 MPa提高至23.7 MPa,断裂伸长率从365%提高至408%,同时乳液的粘度下降,干燥时间变短,胶膜的附着力变好。     

有机硅-聚氨酯共聚乳液的制备和乳胶膜相结构及其性能研究

以端羟丙基聚二甲基硅氧烷(HP-PDMS)、异佛尔酮二异氰酸酯、2,2-二羟甲基丁酸等为主要原料,采用分步投料法和无皂相反转乳化工艺制得粒径约50 nm的有机硅-聚氨酯共聚乳液,并对有机硅-聚氨酯乳胶膜的相结构和性能进行了表征,考察了HP-PDMS用量对乳胶膜相结构和性能的影响.DSC测试结果显示,与聚醚型聚氨酯乳胶膜相比,有机硅-聚氨酯乳胶膜中存在明显的相分离结构.FTIR分析结果表明,有机硅-聚氨酯乳胶膜硬段之间存在较强的氢键,它促进了相分离结构的形成.从AFM相图上可以观察到有机硅-聚氨酯乳胶膜中存在明显的海岛型相分离结构,其中聚硅氧烷软段的无定形微区构成了岛状分散相.随着有机硅含量的增加,有机硅-聚氨酯乳胶膜的相分离程度增加,弹性模量降低,断裂伸长率和柔韧性显著升高.有机硅-聚氨酯乳胶膜的起始分解温度低于聚醚型聚氨酯乳胶膜,但其在高温阶段的稳定性明显优于后者;对乳胶膜接触角和吸水率的研究表明,有机硅-聚氨酯乳胶膜的耐水性远高于聚醚型聚氨酯乳胶膜.     

端羟基聚丙烯酸酯改性水性聚氨酯

将丙烯酸丁酯(BA)、甲基丙烯酸甲酯(MMA)通过溶液自由基聚合,用巯基乙醇作为链转移剂调控合成了一定分子量的端羟基聚丙烯酸酯(PA),再与聚氨酯(PU)预聚体反应,在水中分散得到PA-PU-PA三嵌段共聚复合乳液。 采用FTIR和¹HNMR测试技术对共聚物结构进行了表征。 结果表明,随着PU与PA质量比的降低,共聚物中丙烯酸酯含量随之增加;PU软硬链段之间的氢键化作用减弱。 TEM显示,复合乳胶粒子形态均匀规整,并呈现明显的核壳结构。改性后的乳胶膜耐水、耐热性能均随着PU/PA质量比的减小而提高,吸水率由25%降低至5%,最大热失重温度由369 ℃提高至432 ℃。     

偶联剂对丙烯酸酯改性聚氨酯聚合物接枝率和乳液性能的影响

合成了含双羟基的甲基丙烯酸甘油酯(GM)并将其作为偶联剂用于聚丙烯酸酯(PAC)对水基聚氨酯(PU)的改性.采用核磁共振、红外光谱和气相色谱等对GM进行了表征.分别以该双羟基GM和单羟基的丙烯酸羟乙酯(HEA)与异氰酸酯基(NCO)封端的PU预聚体进行反应以在PU分子链上引入双键,然后再与丙烯酸酯类单体通过自由基聚合制...     

细胞相容性聚氨酯的合成及其细胞相容性研究

在紫外光和过氧化氢的共同作用下,过氧化氢基团被引人到聚氨酯膜(PU)表面.将丙烯酸羟乙酯(HEA)吸附于氧化后的PU膜表面,在紫外光下实现了膜表面的接枝,并考察了接枝膜的表面性能.人体脐带静脉内皮细胞粘附和生长的研究表明,HEA接枝后的PU表面细胞粘附率显著提高,细胞的生长速率加快,增值率提高.     

MMA-EA-AA无皂乳液聚合中粒径及粒径分布的控制

系统研究了MMA EA AA三元无皂乳液聚合体系中各种因素对乳胶粒大小及分布的影响 ,制得了单分散、粒径在 30 0～ 6 0 0nm可控聚合物乳胶粒 .结果表明 ,在过硫酸铵用量一定的条件下 ,聚合初期加入大量引发剂可同时提高单体转化率和乳胶粒的单分散性 ;随着引发剂和AA用量的增加以及聚合温度的升高 ,胶粒粒径逐渐减小 ,转化率逐渐升高 ;随着NH4 HCO3用量的增加 ,粒径逐渐增大 ,当NH4 HCO3用量达到 0 5g以后 ,转化率逐渐降低 ;搅拌速率为 30 0r min左右时 ,单体转化率最高 ,所得乳胶粒粒径最均一 .     

聚硅氧烷-聚丙烯酸酯-聚氨酯三元复合乳液的制备与表征及其胶膜性能

用异佛尔酮二异氰酸酯与仲羟基封端的聚硅氧烷(PMTS)反应在聚硅氧烷分子链端引入异氰酸酯基团, 然后将其与聚丙二醇、二羟甲基丙酸等反应制备聚硅氧烷改性聚氨酯(PSU)预聚体, 再以甲基丙烯酸甘油酯(GM)为偶联剂在PSU链上引入双键, 最后加入丙烯酸酯单体和交联剂乳化后通过乳液聚合制备了偶联型聚硅氧烷聚丙烯酸酯改性聚氨酯(PSU-X-AC)三元复合乳液. 同样条件下不使用偶联剂制备了非偶联型三元复合乳液(PSU-AC). 无论是否使用偶联剂, 三元复合乳液的稳定性都明显优于不含PAC的PSU二元乳液. 对于三元复合乳液及其胶膜的性能表征结果显示, 与非偶联型PSU-AC三元乳液相比, 偶联型PSU-X-AC乳液的乳胶粒尺寸较小, 粒径分布更均一|偶联型三元乳液的表面张力较小|其胶膜的力学强度远优于非偶联型|除非在PMTS分子量较高的情况下, 偶联型乳胶膜中未观察到非偶联型所见的相分离, 偶联剂GM的使用对提高材料的憎水及力学性能有明显作用. PMTS分子量及其用量对乳液的乳胶粒径、表面张力和粘度影响不明显. 但对于复合胶膜的性能来说, 三元复合乳液聚合物中PMTS分子量及其用量存在上限, 分子量上限值约为2000, 其用量上限约为PSU二元聚合物的10%, 在此之下PMTS的使用可以明显提高胶膜的力学及耐水性能.     

水性聚氨酯结构与胶膜性能的关系

为制备一种性能优异的水性聚氨酯涂层,以聚丙二醇和异佛尔酮二异氰酸酯为主要原料,用本体聚合法制备了水性聚氨酯,考察了结构组元对胶膜性能的影响,并用激光粒度仪、微机控制电子万能试验机和同步热分析仪进行了表征。结果表明:当硬段含量增加时,乳液粒径增大,胶膜拉伸强度增加,吸水率升高;当异氰酸根指数增大时,乳液粒径增大,胶膜拉伸强度增加,吸水率降低;当亲水性扩链剂含量和中和度增大时,乳液粒径减小,胶膜的拉伸强度增加,吸水率升高;在硬段比例为50%、异氰酸酯指数为1.35、亲水性扩链剂含量为5%、中和度为1的条件下,胶膜性能较佳(拉伸强度为16MPa,断裂伸长率为556%,吸水率为6.2%)且在丙酮和甲苯中均表现出溶胀现象。     

亲水单体对聚氨酯-含氟丙烯酸酯复合乳液颗粒和表面性能的影响

为了提高聚氨酯-丙烯酸酯聚合物的耐水性和耐溶剂性, 将N-甲基二乙醇胺(MDEA)扩链的交联聚氨酯丙酮溶液作为反应介质, 以苯乙烯、丙烯酸丁酯、含氟丙烯酸酯(FA)为单体, 过氧化苯甲酰为引发剂, 通过溶液聚合相转化法制得新型阳离子聚氨酯-含氟丙烯酸酯复合乳液. 研究了MDEA对聚合物水分散液的乳胶粒径、Zeta电位以及乳胶膜表面性能的影响, 并用FTIR, TEM对聚合物的结构和乳胶粒形态进行了表征. 结果表明, MDEA的添加利于降低乳胶粒径, 但对乳胶膜的疏水性能有不利影响, 当MDEA的质量分数为13.15%时, FPUA乳胶粒的形态呈球形, 粒径约为253 nm, 乳胶膜的表面自由能低于25.1 mJ/m², 接触角衰减速率约为0.38 (º)/min. 另外, 乳胶膜的高温处理能够使表面自由能降低11.5%以上.     

单油酸三羟甲基丙烷酯改性水性聚氨酯

利用单油酸三羟甲基丙烷酯(TMPM)、异佛尔酮二异氰酸酯(IPDI)和聚氧化丙烯(PPG)等制备水性聚氨酯。采用透射电镜(TEM)、动态激光光散射(DLLS)、红外光谱(FT-IR)、热重分析(TGA)和表面张力仪表征了乳液胶束形态、产物结构及性能。结果表明:水性聚氨酯(PU)分子上引入脂肪侧链容易在水中形成规整的胶束,但TMPM改性的水性聚氨酯胶束粒径随TMPM含量的增加不断增大,当w(TMPM)=0.07时,乳液不稳定;脂肪侧链的引入降低了水性聚氨酯乳液的表面张力,表面张力随着反应体系中—NCO和—OH摩尔比的增大而降低,随交联度的增大先增加后减小;TMPM的引入可以提高胶膜的热稳定性。     

Polyurethane acrylate microgel synthesized by emulsion polymerization using unsaturated self-emulsified polymer

Polyurethane (PU) acrylate microgels were obtained by emulsion polymerization of self-emulsified PU acrylate terminated by 2-hydroxyethyl methacrylate without any extra emulsifier and crosslinker. Moreover, the PU acrylate was also used as stabilizer and crosslinker to synthesize poly(methyl methacrylate) (PMMA)–PU composite microgels via emulsion polymerization, which provided a new method to synthesize PU microgels and their composite microgels. The kinetics of microgel synthesis was studied by gel permeation chromatography. The dynamic rheological behaviors indicated that a crosslinked structure was formed. The frequency dependency of the loss tangent and complex viscosities showed strong relationships with the microgel structure. Those microgels with rigid PMMA core showed higher ability to slide than the soft PU acrylate microgel, which had influence on the changing of loss tangent with frequency. All the microgels swollen in tetrahydrofuran exhibited high viscosities and strong shear-thinning behaviors. As a sort of flexible microgel, the PU microgel was able to form a coherent film at room temperature, which was distinct from hard microgels.     

Determination of Crosslinking and Grafting in Polyurethane-acrylic Hybrid Material and Their Theoretical Calculations

A theoretical method to calculate the mode of polyurethane(PU) prepolymers grafted to polyacrylic(PAC) was presented. Using hydroxyethyl acrylate(HEA) as coupling agent, polyurethane-acrylics(PU-AC) hybrid latexes were prepared with varying HEA level and the reaction of HEA with PU prepolymers at different temperatures, and PU grafted to PAC was experimentally determined. The results show that PU grafted to PAC regularly increased, and the non-grafted and linear free PU regularly decreased with increase in ...     

Polyurethane (urea)/polyacrylates interpenetrating polymer network (IPN) adhesives for low surface energy materials

On the basis of the polymerization of the acrylate phase catalyzed by the oxidation of trialkylborane at room temperature, a series of polyurethane (urea)/polyacrylates adhesives with interpenetrating polymer network structure (IPNS) was synthesized. The crosslinking polyurethane (urea) phase was synthesized by the reaction between polymer diamine or triol and isocyanate. The resulting IPN adhesives as a function of the polyurethane (urea) or 2‐hydroxylethyl acrylate terminated polyurethane (HEA‐PU) (crosslinking agent of acrylate phase) content were explored. The adhesive morphology took on the IPNS that manifested as a finely dispersed polyurethane (urea) phase in the acrylate phase. Excellent adhesion to low surface energy materials was achieved within a wide range of polyurethane (urea) contents. The IPN adhesives also displayed better flexibility than polyacrylate adhesives with HEA‐PU as a crosslinking agent. Copyright © 2011 John Wiley & Sons, Ltd.     

The Interrelation Between the Microphase Structure of Sequential Interpenetrating Polymer Networks and the Crosslinking Density of Penetrating Networks

The microphase structure of single polyurethane (PU) and acrylate networks as well as sequential interpenetrating polymer networks (IPNs), produced by the forming of a PU network in the presence of monomers of a penetrating network, was studied by small- and wide-angle x-ray analysis. It was established that each network component was of a two-phase structure consisting of disordered phase-separated microregions. the higher crosslink density of the acrylate network results in its higher heterogeneity. in IPNs, phase separation of a complex nature is realized: the PU matrix preserves some features of a single network structure, and the second component forms microregions 5-10 nm in size while retaining a certain level of interpenetra-tion of both network components. the microphase structure parameters of such systems are greatly dependent on the crosslink density of the penetrating network. This suggests the influence of a three-dimensional network of chemical bonds on the interdiffusion of branched fragments of the penetrating network and molecular chains of the matrix, one leading to the retardation of phase separation.     

Polyurethane/polyethyl acrylate interpenetrating polymer networks

The thermal decomposition kinetics of polyurethane/polyethyl acrylate interpenetrating polymer networks (PU/PEA IPN) were studied by means of thermogravimetry and derivative thermogravimetry (TG-DTG), and compared with those of polyurethane (PU) and polyethyl acrylate (PEA). The decomposition temperature (T _i) of PU/PEA IPN was found to be higher thanT _i of PEA, but lower thanT _i of PU. Thermal decomposition kinetic parameters,n andE, estimated using Coats-Redfern method, are found for PU/PEA IPN, PU and PEA to be 1.6, 1.9 and 1.1, and 196.6, 258.6 and 139.2 kJ mol^–1, respectively. The results show that PU/PEA IPN is neither a simple mixture of PU and PEA nor a copolymer of them. The mechanism of thermal decomposition of PU/PEA IPN is different from those of PU and PEA. The special network in PU/PEA IPN effectually protects weak bonds in the molecular chain of PU and PEA.We express our thanks to Dr. Yaxiong Xie and Zhiyuong Ren for their help in this work,     

聚氨酯/苯丙杂化乳液的合成、表征和特性及其在复膜胶中的应用

由聚氨酯(PU)预聚物、丙烯酸丁酯和苯乙烯单体的乳液聚合制备了聚氨酯-苯乙烯-丙烯酸酯(PUSA)杂化乳液,1H NMR显示所得的PU预聚物由烯烃基团封端。 TEM表明,其粒径约为150 nm,且为颜色深浅不同的两部分所组成。 随着PU含量的降低,杂化乳液的热稳定性增加。 DSC分析表明,所得杂化乳液有单一的Tg值,且处于聚氨酯和聚苯丙(PSA)乳液Tg值的中间。 当将得到的杂化乳液用于纸塑和塑塑复合时,其剥离强度分别为14.1 N/2.5 cm和12.2 N/2.5 cm。     

A novel approach to fluorinated polyurethane by macromonomer copolymerization

For the first time, through macromonomer radical copolymerization, a novel fluorinated polyurethane (FPU) was synthesized based on partly acrylate-endcapped polyurethane macromonomers with hexafluorobutyl acrylate (HFBA). Partly acrylate-endcapped polyurethane (PU) macromonomers were synthesized using isophronediisocyanate (IPDI), dimethylol propionic acid (DMPA), polyethylene adipate glycols (PEA) etc. The novel fluorinated polymer, which bore PU side chains and fluorinated side chains, was confirmed by F¹⁹ NMR spectroscopy, X-ray photoelectron spectroscopy (XPS), elemental analysis, scanning electron spectroscopy (SEM) etc. Copolymerization of polyurethane macromonomers with hexafluorobutyl acrylate (HFBA) was briefly investigated. The surface tension of FPU solution was measured and showed sharply decrease compared to that of pure polyurethane. Results from SEM showed a uniform size distribution of phase micro-domains on the fracture surface of FPU.     

Formation Mechanism and Tensile Mechanical Properties of Poly(acrylamide-co-octylphenol polyoxyethylene (10) acrylate) Hydrophobic Association Hydrogels With High Toughness

Poly(acrylamide-co-octylphenol polyoxyethylene (10) acrylate) hydrophobic association hydrogels, which is abbreviated to poly(AM-co-OP10/AC) HA-gels, were prepared through micellar copolymerization of acrylamide (AM) and a small amount of octylphenol polyoxyethylene (10) acrylate (OP10/AC) in the presence or absence of sodium dodecyl sulfate (SDS). For poly(AM-co-OP10/AC) HA-gels, formation mechanism was discussed in detail, which can reasonably explain the reason that tensile mechanical properties of the hydrogels (containing SDS) are much higher than those of the hydrogels (not containing SDS). In addition, according to the tensile experimental results of poly(AM-co-OP10/AC) HA-gels, the effect of composition content in the initial solutions on tensile mechanical properties was investigated in detail. The results clearly indicate tensile strength, elastic modulus and elongations for poly(AM-co-OP10/AC) HA-gels strongly depended on composition content in the initial solutions.