Comparison of adsorbents for on-line solid-phase extraction of polycyclic aromatic hydrocarbons before liquid chromatography with UV detection

Summary On-line solid-phase extraction (SPE) coupled with reversed-phase liquid chromatography and UV detection at 254 nm has been used for the determination of trace-level polycyclic aromatic hydrocarbons (PAH) in soil extracts. Five commercially available adsorbents (C₈, C₁₈, PLRP-S, PRP-1, and Bond-Elut Env) were evaluated. Results showed that recovery of the PAH decreased with increasing molecular weight, because of their poorer solubility. Recovery of high-molecular-weight PAH was significantly improved by addition of 10% (v/v) acetonitrile to the sample before loading of the SPE adsorbent. PAH recovery ranged from 64.0 to 108% when a 50 mL sample spiked with 1 μg L⁻¹ was applied to these adsorbents. Determination of PAH was possible with detection limits below 0.05 μg L⁻¹, which corresponds to 0.2 μg kg⁻¹ soil. The method was successfully used to determine PAH in soil extracts.     

Multiresidue procedures for determination of triazine and organophosphorus pesticides in water by use of large-volume PTV injection in gas chromatography

Summary Two procedures, based on large-volume injection with a programmed-temperature vaporizer (PTV), have been developed for the determination of several triazine and organophosphorus pesticides. The use of PTV for injection in gas chromatography (GC) has enabled the introduction of up to 200 μL sample extract into the GC, thus increasing the sensitivity of the method. PTV injection has been combined off-line with two different microextraction procedures—liquid-liquid partition and solid-phase extraction. A simple and rapid off-line liquid-liquid microextraction procedure (5 mL water/1 mL methyltert-butyl ether) was applied to surface water samples spiked at levels between 0.01 and 5μg L⁻¹. Recoveries of the overall procedure were >80% and the precision was better than 15%. Detection limits were <30 ngL⁻¹ from 200-μL injections in GC-NPD analysis of triazines and GC-FPD analysis of organophosphorus pesticides. Off-line automated solid-phase extraction with C₁₈ cartridges has been applied to water samples (50 mL) spiked at 0.01, 0.1 and 1 μg L⁻¹. The overall procedure was satisfactory (recoveries >80% and coefficients of variation <12%) and the limits of detection ranged from 1 to 9 ng L⁻¹. Finally, several surface water samples were anlysed, and triazine herbicides were detected at concentrations of approx. 0.1–0.2 μg L⁻¹. The results were similar to those obtained by conventional solvent extraction then GC-MSD after splitless injection of 2 μL.     

High-performance liquid chromatographic determination/identification of oxytetracycline and sulphadimidine in meat and eggs

Summary A rapid method for the simultaneous determination/identification of residual oxytetracycline (OTC) and sulphadimidine (SDD) in meats (beef, pork, chicken) and eggs by high-performance liquid chromatography (HPLC) was developed. The extraction of OTC and SDD was performed using a Sep-Pak^? CN cartridge. The extracts contained OTC/SDD analytes when examined by HPLC using a LiChrospher^? 100 RP-8 end-capped column and a mobile phase of acetonitrile-acetic acid-water (28:4:68, v/v/v) with a photodiode array detector. The average recoveries from spiked samples (0.1 μg g⁻¹ and 1.0 μg g⁻¹) were in excess of 80.2% with coefficients of variation between 1.5 and 5.0%. The limits of detection for OTC and SDD were 0.05 and 0.02 μg g⁻¹, respectively.     

Determination of isopropylthioxanthone (ITX) in milk, yoghurt and fat by HPTLC-FLD, HPTLC-ESI/MS and HPTLC-DART/MS

Two new HPTLC methods for quantification of isopropyl-9H-thioxanthen-9-one (ITX) in milk, yoghurt and fat samples have been developed. Extraction of ITX from milk and yoghurt was performed with a mixture of cyclohexane and ethyl acetate by employment of accelerated solvent extraction (ASE). For soy bean oil and margarine, a simple partitioning of ITX into acetonitrile was used. ITX and 2,4-diethyl-9H-thioxanthen-9-one (DTX) used as internal standard have been separated on silica gel 60 HPTLC plates with a mixture of toluene and n-hexane (4:1, v/v) and on RP18 HPTLC plates with a mixture of acetonitrile and water (9:1, v/v). Development was performed anti-parallel from both plate sides leading to a throughput of 36 separations in 7 min. Fluorescence measurement at 254/>400 nm was used for quantification. Limits of detection (S/N of 3) have been established to be 64 pg for ITX and DTX on both types of HPTLC plates. In fatty matrix (spiked butter) LOD of ITX was determined to be 1 μg kg⁻¹. In the working range monitored (20–200 μg kg⁻¹) polynomial regression of ITX showed a relative standard deviation (sdv) of ±1.51 % (r=0.99981). Starting with the limit of quantification the response was linear (sdv=±2.18 %, r=0.99893). Regarding repeatability (n=9) a coefficient of variation (CV) of 1.1 % was obtained for ITX at 32 ng on silica gel plates and of 2.9 % on reversed-phase plates. Repeatabilities (n=4) of ITX determination at 20, 50 and 100 μg kg⁻¹ in milk, yoghurt, soybean oil and margarine showed CVs between ±1.0 and 6.4 %. The results prove that modern planar chromatography is a rapid and cost-efficient alternative method to quantify ITX in milk-based or fatty matrices. Only positive results are confirmed by online ESI/MS in the SIM mode (LOQ 128 pg) and by DART/MS involving a minimal employment of the MS device, which is a further advantage of HPTLC. Overall mean recovery rates of ITX at 20 or 50 and 100 μg kg⁻¹ (n=8) were 41 % for milk, 70 % for yoghurt, 6 % for margarine and 12 % for soy bean oil. However, with the internal standard correction recoveries were about 130 % for milk and yoghurt and 70 and 97 % for margarine and soy bean oil, respectively.      

Simplified liquid-chromatographic determination of residues of tetracycline antibiotics in eggs

Summary A high-performance liquid chromatographic (HPLC) procedure is described for the identification and quantification of residues of tetracycline antibiotics (TCA) (oxytetracycline, tetracycline, chlortetracycline, and doxycycline), in eggs. Spiked and blank samples were prepared by homogenization with 1∶1 (v/v) acetonitrile-mixed Mcllvaine buffer and EDTA solution (pH 4.0) then centrifugal ultrafiltration. HPLC was performed on a reversed-phase column with acetonitrile-5% (v/v) aqueous acetic acid, 35∶65 (v/v), as mobile phase and photo-diode array detection. Average recoveries (each drug spiked at 0.1, 0.2, 0.3, 0.5 and 1.0 μg g⁻¹) were >-77% with standard deviations (SD) between 1.5 and 3.5%. The inter-assay variabilities and theirSD were <3.4% and <0.7%, respectively, and intra-assay variability was between 2.0 and 3.9%. The limits of quantitation (LOQ) were 0.064 0.087, 0.121, and 0.131 μg g⁻¹ for OTC, TC, CTC, and DC, respectively. The total time required for the analysis of one sample was less than 30 min.     

Fast quantitation of 5-hydroxymethylfurfural in honey using planar chromatography

An approach for rapid quantitation of 5-hydroxymethylfurfural (HMF) in honey using planar chromatography is suggested for the first time. In high-performance thin-layer chromatography (HPTLC) the migration time is approximately 5 min. Detection is performed by absorbance measurement at 290 nm. Polynomial calibration in the matrix over a range of 1:80 showed correlation coefficients, r, of ≥ 0.9997 for peak areas and ≥ 0.9996 for peak heights. Repeatability in the matrix confirmed the suitability of HPTLC–UV for quantitation of HMF in honey. The relative standard deviation (RSD, %, n = 6) of HMF at 10 ng/band was 2.9% (peak height) and 5.2% (peak area); it was 0.6% and 1.0%, respectively, at 100 ng/band. Other possible detection modes, for example fluorescence measurement after post-chromatographic derivatization and mass spectrometric detection, were also evaluated and can coupling can be used as an additional tool when it is necessary to confirm the results of prior quantitation by HPTLC–UV. The confirmation is provided by monitoring the HMF sodium adduct [M + Na]⁺ at m/z 149 followed by quantitation in TIC or SIM mode. Detection limits for HPTLC–UV, HPTLC–MS (TIC), and HPTLC–MS (SIM) were 0.8 ng/band, 4 ng/band, and 0.9 ng/band, respectively. If 12 μL honey solution was applied to an HPTLC plate, the respective detection limits for HMF in honey corresponded to 0.6 mg kg⁻¹. Thus, the developed method was highly suitable for quantitation of HMF in honey at the strictest regulated level of 15 mg kg⁻¹. Comparison of HPTLC–UV detection with HPTLC–MS showed findings were comparable, with a mean deviation of 5.1 mg kg⁻¹ for quantitation in SIM mode and 6.1 mg kg⁻¹ for quantitation in TIC mode. The mean deviation of the HPTLC method compared with the HPLC method was 0.9 mg kg^-1 HMF in honey. Re-evaluation of the same HPTLC plate after one month showed a deviation of 0.5 mg kg⁻¹ HMF in honey. It was demonstrated that the proposed HPTLC method is an effective method for HMF quantitation in honey.      

Determination of fumonisins B1 and B2 in Portuguese maize and maize-based samples by HPLC with fluorescence detection

Fumonisins B₁ (FB₁) and fumonisin B₂ (FB₂) are the main members of a family of mycotoxins produced by Fusarium verticillioides, Fusarium proliferatum, and other fungi species of the section Liseola. The present work shows the results of comparative studies using two different procedures for the analysis of fumonisins in maize and maize-based samples. The studied analytical methods involve extraction with methanol/water, dilution with PBS, and clean-up through immunoaffinity columns. Two reagents (o-phthaldialdehyde and naphthalene-2,3-dicarboxaldehyde) were studied for formation of fluorescent derivatives. The separation and identification were carried out by high-performance liquid chromatography with fluorescence detection. The optimized method for analysis of fumonisins in maize involved extraction with methanol/water (80:20), clean-up with an immunoaffinity column, and derivatization with naphthalene-2,3-dicarboxaldehyde (NDA). The limit of detection was 20 μg kg⁻¹ for FB₁ and 15 μg kg⁻¹ for FB₂. Recoveries of FB₁ and FB₂ ranged from 79% to 99.6% for maize fortified at 150 μg kg⁻¹ and 200 μg kg⁻¹, respectively, with within-day RSDs of 3.0 and 2.7%. The proposed method was applied to 31 samples, and the presence of fumonisins was found in 14 samples at concentrations ranging from 113 to 2,026 μg kg⁻¹. The estimated daily intake of fumonisins was 0.14 μg kg⁻¹ body weight per day.     

Determination of Aldehydes and Ketones in Fuel Ethanol by High-Performance Liquid Chromatography with Electrochemical Detection

A new methodology was developed for analysis of aldehydes and ketones in fuel ethanol by high-performance liquid chromatography (HPLC) coupled to electrochemical detection. The electrochemical oxidation of 5-hydroxymethylfurfural, 2-furfuraldehyde, butyraldehyde, acetone and methyl ethyl ketone derivatized with 2,4-dinitrophenylhydrazine (DNPH) at glassy carbon electrode present a well defined wave at +0.94 V; +0.99 V; +1.29 V; +1.15 V and +1.18 V, respectively which are the basis for its determination on electrochemical detector. The carbonyl compounds derivatized were separated by a reverse-phase column under isocratic conditions with a mobile phase containing a binary mixture of methanol / LiClO_4(aq) at a concentration of 1.0 × 10⁻³ mol L⁻¹ (80:20 v/v) and a flow-rate of 1.1mL min⁻¹ . The optimum potential for the electrochemical detection of aldehydes-DNPH and ketones-DNPH was +1.0 V vs. Ag/AgCl. The analytical curve of aldehydes-DNPH and ketones-DNPH presented linearity over the range 5.0 to 400.0 ng mL⁻¹, with detection limits of 1.7 to 2.0 ng mL⁻¹ and quantification limits from 5.0 to 6.2 ng mL⁻¹, using injection volume of 20 μL. The proposed methodology was simple, low time-consuming (15 min/analysis) and presented analytical recovery higher than 95%.     

Determination of Trihalomethanes in Drinking Water by Dispersive Liquid–Liquid Microextraction then Gas Chromatography with Electron-Capture Detection

Dispersive liquid–liquid microextraction (DLLME) has been used for preconcentration of trihalomethanes (THMs) in drinking water. In DLLME an appropriate mixture of an extraction solvent (20.0 μL carbon disulfide) and a disperser solvent (0.50 mL acetone) was used to form a cloudy solution from a 5.00-mL aqueous sample containing the analytes. After phase separation by centrifugation the enriched analytes in the settled phase (6.5 ± 0.3 μL) were determined by gas chromatography with electron-capture detection (GC–ECD). Different experimental conditions, for example type and volume of extraction solvent, type and volume of disperser solvent, extraction time, and use of salt, were investigated. After optimization of the conditions the enrichment factor ranged from 116 to 355 and the limit of detection from 0.005 to 0.040 μg L⁻¹. The linear range was 0.01–50 μg L⁻¹ (more than three orders of magnitude). Relative standard deviations (RSDs) for 2.00 μg L⁻¹ THMs in water, with internal standard, were in the range 1.3–5.9% (n = 5); without internal standard they were in the range 3.7–8.6% (n = 5). The method was successfully used for extraction and determination of THMs in drinking water. The results showed that total concentrations of THMs in drinking water from two areas of Tehran, Iran, were approximately 10.9 and 14.1 μg L⁻¹. Relative recoveries from samples of drinking water spiked at levels of 2.00 and 5.00 μg L⁻¹ were 95.0–107.8 and 92.2–100.9%, respectively. Comparison of this method with other methods indicates DLLME is a very simple and rapid (less than 2 min) method which requires a small volume of sample (5 mL).     

Tetracycline residues in royal jelly and honey by liquid chromatography tandem mass spectrometry: validation study according to Commission Decision 2002/657/EC

A specific, sensitive and robust liquid chromatography tandem mass spectrometry method for determining oxytetracycline, tetracycline, chlortetracycline and doxycycline in royal jelly and honey samples is presented. Extraction of drug residues was performed by ammonium acetate buffer as extractant followed by a clean-up with metal chelate affinity chromatography and solid-phase extraction. Tetracycline analysis was performed using liquid chromatography–electrospray ionisation–tandem mass spectrometry. The presented method is the first validated for royal jelly and in accordance with the requirements set by Commission Decision 2002/657/EC. Recoveries of the methods, calculated spiking the samples at 5.0, 10.0, 20.0 and 30.0 μg kg⁻¹, were 79% to 90% for honey and 77% to 90% for royal jelly. The intra-day precision (RSD) ranged between 8.1% and 15.0% for honey and from 9.1% to 16.3% for royal jelly, while inter-day precision values were from 10.2% to 17.6% and from 10.6% to 18.4% respectively for honey and royal jelly. Linearity for the four analytes was calculated from 5.0 to 50.0 μg kg⁻¹. The decision limits (CCα) ranged from 6.2 to 6.4 μg kg⁻¹ and from 6.1 to 6.5 μg kg⁻¹ for honey and royal jelly, respectively. Detection capabilities values (CCβ) ranged between 7.2 and 7.7 μg kg⁻¹ and from 7.3 to 7.9 μg kg⁻¹ respectively for honey and royal jelly. The developed method is currently in use for confirmation of the official control analysis of honey and royal jelly samples.     

Simultaneous LC Determination of Ginsenosides Using a Modified Extraction Procedure and an Improved Step Gradient Program

A novel, accurate and precise high performance liquid chromatographic method has been developed for simultaneous determination of seven important ginsenosides (Rg1, Re, Rf, Rb1, Rc, Rb2 and Rd) in ginseng products. The separation was performed on a Shim-pack VP-ODS column (5 μm, 150 ×2 mm i.d) with ultraviolet detection at 200 nm by using the improved step gradient elution program. The LODs (S/N = 3) were in the range 0.29 to 1.33 ng μL⁻¹. All calibration curves showed a good linearity (R² > 0.998) over the ranges tested. The recoveries obtained from spiked sample were between 95.1% and 98.7%. The proposed method was successfully applied to several ginseng pharmaceutical samples. For the sample preparation, a modified extraction method was made to improve the extraction efficiency by evaluation of five solvent systems. The results demonstrated that the extraction with methanol-water (80:20, v/v) is suitable method preferably for the extraction of the ginsenosides. On leave from Department of Pharmacy and Applied Chemistry, Jilin Institute of Chemical Technology, Jilin 132022, P. R. China     

HPLC Determination of DCJW in Rat Plasma and Its Application to Pharmacokinetics Studies

A high-performance liquid chromatography–UV method for determining DCJW concentration in rat plasma was developed. The method described was applied to a pharmacokinetics study of intramuscular injection in rats. The plasma samples were deproteinized with acetonitrile in a one-step extraction. The HPLC assay was carried out using a VP-ODS column and the mobile phase consisting of acetonitrile–water (80:20, v/v) was used at a flow rate of 1.0 mL min⁻¹ for the effective eluting DCJW. The detection of the analyte peak area was achieved by setting a UV detector at 314 nm with no interfering plasma peak. The method was fully validated with the following validation parameters: linearity range 0.06–10 μg mL⁻¹ (r > 0.999); absolute recoveries of DCJW were 97.44–103.46% from rat plasma; limit of quantification, 0.06 μg mL⁻¹ and limit of detection, 0.02 μg mL⁻¹. The method was further used to determine the concentration–time profiles of DCJW in the rat plasma following intramuscular injection of DCJW solution at a dose of 1.2 mg kg⁻¹. Maximum plasma concentration (C _max) and area under the plasma concentration–time curve (AUC) for DCJW were 140.20 ng mL⁻¹ and 2405.28 ng h mL⁻¹.     

Determination of arsenic in diesel, gasoline and naphtha by graphite furnace atomic absorption spectrometry using microemulsion medium for sample stabilization

A procedure for the determination of As in diesel, gasoline and naphtha at μg L⁻¹ levels by GFAAS is proposed. Sample stabilization was achieved by the formation of three component solutions prepared by mixing appropriate volumes of the samples propan-1-ol and nitric acid aqueous solution. This mixture resulted in a one-phase medium, which was indefinitely stable. No changes in the analyte signals were observed over several days in spiked samples, proving long-term stabilization ability. The use of conventional (Pd) and permanent (Ir) modification was investigated and the former was preferred. Central composite design multivariate optimization defined the optimum microemulsion composition as well as the temperature program. In this way, calibration using aqueous analytical solutions was possible, since the same sensitivity was observed in the investigated microemulsion media and in 0.2% v/v HNO₃. Coefficients of correlation larger than 0.999 and an As characteristic mass of 22 pg were observed. Recoveries (n=4) obtained from spiked samples were 98±4, 99±3 and 103±5%, and the limits of detection in the original samples were 1.8, 1.2 and 1.5 μg L⁻¹ for diesel, gasoline and naphtha, respectively. Validation was performed by the analysis of a set of commercial samples by independent comparative procedures. No significant difference (Student’s t-test, p<0.05) was observed between comparative and proposed procedure results. The total determination cycle lasted 4 min for diesel and 3 min for gasoline and naphtha, equivalent to a sample throughput of 7 h⁻¹ for diesel and 10 h⁻¹ for gasoline and naphtha.     

Determination of phenolic compounds in water samples by on-line solid-phase extraction—supercritical-fluid chromatography with diode-array detection

Summary The eleven Environmental Protection Agency (EPA) priority phenolic compounds have been determined by solid-phase extraction (SPE) coupled on-line to supercritical-fluid chromatography (SFC) with diodearray detection. The variables affecting chromatographic separation were optimized and the analytes were separated at 40 °C in two diol columns connected in series; a gradient of methanol, as modifier, and CO₂ was used as mobile phase. Under these conditions, all the compounds studied were separated to baseline in less than 13 min. PLRP-S and LiChrolut EN were tested as sorbents in a 10×3 mm i.d. laboratory-packed precolumn for solid-phase extraction. An ion-pair reagent, tetrabutylammonium bromide (TBA), was used in the extraction process to increase break-through volumes. The performance of the method was checked with tap and river waters and the pre-concentration of 20 mL of sample in a PLRP-S pre-column enabled phenolic compounds to be determined at low μg L⁻¹ levels with limits of detection ranging between 0.4 and 2 μg L⁻¹. The repeatability and reproducibility between days (n=3) for real samples spiked at 10 μg L⁻¹ were lower than 10%.     

Simple Liquid Chromatographic Determination of Minocycline in Brain and Plasma

A new high-performance liquid chromatography assay was developed for the determination of minocycline in plasma and brain. A solid–liquid extraction procedure was coupled with a reversed-phase HPLC system. The system requires a mobile phase consisting of acetonitrile:water:perchloric acid (26:74:0.25, v/v/v) adjusted to pH 2.5 with 5 M sodium hydroxide for elution through a RP8 column (250 × 3.0 mm, i.d.) with UV detection set at 350 nm. The method proved to be accurate, precise (RSD < 20%) and linear between 0.15–20 μg mL⁻¹ in plasma and 1–20 μg mg⁻¹ in brain. The method was successfully applied to a blood-brain barrier minocycline transport study.     

Determination of carbetamide in groundwater by micro liquid-liquid extraction and gas chromatography-mass spectrometry

Summary A method is proposed for the determination of carbetamide in water below European Union guidelines (detection limit,DL, below 0.1 μgL⁻¹). Micro liquid-liquid extraction with dichloromethane affords carbetamide which is converted to aniline by hydrolysis. Identification and quantification of aniline was performed by GC-MS. The retention time was 4.24 min. Quantification was achieved by single-ion monitoring (SIM) atm/z 66 and 93. Clean-up is not necessary before SIM. Deuterated anthracene (²H₁₀-anthracene) was used as internal standard. The method was used to determine carbetamide in different types of water sample spiked at very low concentration levels (0.13–10.00 μgL⁻¹). TheDL was 0.04 μgL⁻¹. The effect of the presence of other carbamates was also studied.     

Dispersive liquid–liquid microextraction coupled to liquid chromatography for thiamine determination in foods

A miniaturized dispersive liquid–liquid microextraction (DLLME) procedure coupled to liquid chromatography (LC) with fluorimetric detection was evaluated for the preconcentration and determination of thiamine (vitamin B₁). Derivatization was carried out by chemical oxidation of thiamine with 5 × 10⁻⁵ M ferricyanide at pH 13 to form fluorescent thiochrome. For DLLME, 0.5 mL of acetonitrile (dispersing solvent) containing 90 μL of tetrachloroethane (extraction solvent) was rapidly injected into 10 mL of sample solution containing the derivatized thiochrome and 24% (w/v) sodium chloride, thereby forming a cloudy solution. Phase separation was carried out by centrifugation, and a volume of 20 μL of the sedimented phase was submitted to LC. The mobile phase was a mixture of a 90% (v/v) 10 mM KH₂PO₄ (pH 7) solution and 10% (v/v) acetonitrile at 1 mL min⁻¹. An amide-based stationary phase involving a ligand with amide groups and the endcapping of trimethylsilyl was used. Specificity, linearity, precision, recovery, and sensitivity were satisfactory. Calibration graph was carried out by the standard additions method and was linear between 1 and 10 ng mL⁻¹. The detection limit was 0.09 ng mL⁻¹. The selectivity of the method was judged from the absence of interfering peaks at the thiamine elution time for blank chromatograms of unspiked samples. A relative standard deviation of 3.2% was obtained for a standard solution containing thiamine at 5 ng mL⁻¹. The esters thiamine monophosphate and thiamine pyrophosphate can also be determined by submitting the sample to successive acid and enzymatic treatments. The method was applied to the determination of thiamine in different foods such as beer, brewer’s yeast, honey, and baby foods including infant formulas, fermented milk, cereals, and purees. For the analysis of solid samples, a previous extraction step was applied based on an acid hydrolysis with trichloroacetic acid. The reliability of the procedure was checked by analyzing a certified reference material, pig’s liver (CRM 487). The value obtained was 8.76 ± 0.2 μg g⁻¹ thiamine, which is in excellent agreement with the certified value, 8.6 ± 1.1 μg g⁻¹.     

Determination of Abamectin Residues in Avocados by Microwave-Assisted Extraction and HPLC with Fluorescence Detection

In this article a new analytical method for the confirmation and quantification of abamectin residues in avocados is described. The method allows a fast analysis of abamectin homologues using microwave assisted extraction (MAE), solid-phase extraction (SPE) and high-performance liquid chromatography (HPLC) with fluorescence (FL) detection using trifluoroacetic anhydride (TFAA) and N-methylimidazole (NMIM) as derivatizing agents. The mobile phase consisted of water, methanol and acetonitrile (5:47.5:47.5 v/v/v) and was pumped at a rate of 1.1 mL min⁻¹ (isocratic elution). Homogenized avocado samples were extracted once with 20 mL acetonitrile:water 4:1 (v/v) in a microwave oven for 26 min at 700 W with a maximum temperature of 80 °C. MAE operational parameters were optimized by means of an experimental design. Extracts were cleaned using C₁₈ SPE cartridges. Average recoveries of the method at four spiked levels (0.005, 0.01, 0.10 and 1.0 mg kg⁻¹) were found to be in the range 90–100% with good precision (RSD < 12%). The limits of detection (LODs) and quantification (LOQs) of the whole method were 0.001 and 0.003 mg kg⁻¹, respectively, which are lower than the maximum residue limit (MRL) established by the Spanish and the European legislation in avocados (0.01 mg kg⁻¹). Several avocado samples previously treated with the pesticide were also analyzed.     

Simple and Rapid Determination of Benzoylphenylurea Pesticides in River Water and Vegetables by LC–ESI-MS

Liquid chromatography with electrospray mass spectrometry (LC–ESI-MS) instrumentation equipped with a single quadrupole mass filter has been used to determine several benzoylphenylurea insecticides (diflubenzuron, triflumuron, hexaflumuron, lufenuron and flufenoxuron). Chromatographic and MS parameters were optimised to obtain the best sensitivity and selectivity for all pesticides. Solid-phase extraction (SPE) using C₁₈ cartridges was applied for preconcentration of pesticide trace levels in river water samples. Recoveries of benzoylphenylurea pesticides from spiked river water (0.01 and 0.025 μg L⁻¹) were between 73 and 110% and detection limits were between 3.5 and 7.5 ng L⁻¹. The applicability of the method to the determination of benzoylphenylurea insecticides in spiked cucumber, green beans, tomatoes and aubergines was evaluated. Samples were extracted into dichloromethane without any clean-up step. The limits of detection ranged from 1.0 to 3.2 ng mL⁻¹ (0.68 and 2.13 μg kg⁻¹ in the vegetable samples). Mean recoveries ranged from 79 to 114% at spiking levels of 0.01 and 0.03 mg kg⁻¹. The method was applied to determine traces of benzoylphenylureas in both river water and vegetable samples with precision values lower than 10%. Interferences due to the matrix effect were overcome using matrix-matched standards.     

Isocratic Reversed-Phase HPLC for Simultaneous Separation and Determination of Seven Antiepileptic Drugs and Two of their Active Metabolites in Human Plasma

A simple reversed-phase high-performance liquid chromatographic (HPLC) method has been developed for the simultaneous determination of the antiepileptic drugs (AEDs) zonisamide (ZNS), primidone (PRI), lamotrigine (LTG), phenobarbital (PB), phenytoin (PHT), oxcarbazepine (OXC), and carbamazepine (CBZ) and two of their active metabolites, monohydroxycarbamazepine (MHD) and carbamazepine 10,11-epoxide (CBZE) in human plasma. Plasma (100 μL) was pretreated by deproteinization with 300 μL methanol containing 20 μg mL⁻¹ propranolol hydrochloride as internal standard. HPLC was performed on a C₈ column (4.6 mm × 250 mm; particle size 5 μm) with methanol–acetonitrile–0.1% trifluoroacetic acid, 235:120:645 (v/v), as mobile phase at a flow rate of 1.5 mL min⁻¹. ZNS, OXC, and CBZ were monitored by UV detection at 235 nm, and PRI, LTG, MHD, PB, PHT, and CBZE by UV detection at 215 nm. Relationships between response and concentration were linear over the concentration ranges 1–80 μg mL⁻¹ for ZNS, 5–50 μg mL⁻¹ for PRI, 1–25 μg mL⁻¹ for LTG, 1–50 μg mL⁻¹ for MHD, 5–100 μg mL⁻¹ for PB, 1–10 μg mL⁻¹ for CBZE, 0.5–25 μg mL⁻¹ for OXC, 1–50 μg mL⁻¹ for PHT, and 1–25 μg mL⁻¹ for CBZ. Intra-day and inter-day reproducibility were adequate (coefficients of variation were ≤11.6%) and absolute recovery ranged from 95.2 ± 6.13 to 107.7 ± 7.76% for all the analytes; for the IS recovery was 98.69 ± 1.12%. The method was proved to be accurate, reproducible, convenient, and suitable for therapeutic monitoring of the nine analytes.