Study on rheological behaviour of poly(butylene terephthalate)/montmorillonite nanocomposites

Poly(butylene terephthalate)/montmorillonite composites (PBT/MMT) were prepared by melt intercalation and then investigated using X-ray diffractometer (XRD) and transmission electron microscope (TEM) as well as parallel plate rheometer. It was found that the composites had various phase morphologies with nanoscales and distinct behaviours of a percolation network structure under certain conditions. The linear viscoelastic region of the composites is much narrower than that for PBT matrix, the percolation threshold of the composites is near 3 wt.%, and the percolation network structure is not stable under a shear as well as in a quiescent annealing process. Moreover, PBT/MMT presents the nature of temperature independence of G′ versus G″ whether the internal percolated tactoids network formed or not. The magnitudes of the stress overshoots observed in the reverse flow experiments were strongly dependent on the rest time, which could be inferred that the ruptured network is reorganized under the quiescent annealing process. Furthermore, PBT/MMT shows a strain-scaling stress response to the startup of steady shear, indicating that the formation of the liquid crystalline-like phase structure in the nanocomposites may be the major drive force for the reorganization of the internal network.     

PMMA/MMT nanocomposites prepared by one-step in situ intercalative solution polymerization

Poly(methylmetacrylate)/montmorillonite (PMMA)/(MMT) nanocomposites were prepared by one-step in situ intercalative solution polymerization involving simultaneous modification of MMT with quaternary ammonium salts (QAS), polymerization and polymer intercalation. Polymerization proceeded at 70 °C in a mixture of ethanol and water, whereas the nanocomposite was precipitated with only water. Four QAS’s with different alkyl chain lengths, as well as a QAS with an additional acrylic group, were used to study the influence of the type of quaternary ammonium salt on intercalation. The largest extent of intercalation was achieved in nanocomposites with the QAS having one long alkyl (C16) chain. The obtained PMMA/MMT intercalated nanocomposites exhibited a higher glass transition temperature, better thermal stability, and improved solvent resistance than the pure PMMA.     

SMA/蒙脱石纳米复合材料增容PA6/ABS共混体系

采用原位插层法制备苯乙烯-马来酸酐交替共聚物/蒙脱石(SMA/MMT)纳米复合材料增容PA6/ABS共混体系,并与SMA及MMT的增容效果进行比较,运用TEM、SEM、DSC及XRD研究了增容剂SMA/MMT及MMT的增容机理.结果表明,采用SMA做增容剂,体系机械性能下降;MMT可使体系拉伸强度提高,但冲击强度下降;采用SMA/MMT纳米复合材料做为增容剂,可提高共混体系的强度及韧性.TEM、XRD、DSC及SEM研究结果表明,PA6/ABS/(SMA-MMT)体系中MMT主要分布于两相界面处,ABS及PA6分子链可进入MMT层间,形成类似于共聚物结构,起到增容剂的作用,从而降低分散相粒径,增加两相界面作用力,有利于体系力学性能的提高.PA6/ABS/MMT体系中MMT主要分布于连续相PA6中,虽然对分散相粒径影响较小,但增强了PA6相强度,使得体系力学性能提高.     

原位插层聚合制备聚丁二烯/蒙脱土纳米复合材料的结构与性能研究

聚合物 /粘土纳米复合材料由于具有常规复合材料所没有的结构、形态及更优异的力学、热学、阻燃、阻隔等性能 ,自 1 987由日本丰田公司首次报道了制备尼龙 6 粘土纳米复合材料以来 ,立刻引起人们的普遍关注[1～ 17] .目前报道的聚合物 /粘土纳米复合材料主要集中在以树脂为基体 ,例如 ,聚酰胺[1～ 4] 、聚苯乙烯[5～ 8] 、聚甲基丙烯酸甲酯[9,10 ] 、聚丙烯[11,12 ] 等 .制备以橡胶为基体的橡胶/粘土纳米复合材料研究较少 ,采用的方法多为通过橡胶大分子插层 ,如熔融插层法[1 3] 、溶液插层法[14 ] 、乳液法[15,16] 等 ,这些方法均存在插层…     

Immobilization of poly(fluorene) within clay nanocomposite: an easy way to control keto defect

Blue light emitting cationic polyfluorene polymer(PF)/montmorillonite (MMT) nanocomposites were prepared by solution intercalation and exfoliation method to evaluate the effect of MMT on the nanocomposite structures, properties and morphologies. The properties of PF-MMT composites, containing 1-50 mass% MMT, were characterized unambiguously with the help of multiple analytical techniques, with focus on the keto defect and photostability of PF in the nanocomposites. XRD and HRTEM studies reveal both exfoliation of MMT galleries at lower content of MMT in composites and intercalation of PF chains into the MMT galleries at higher MMT content. The nanocomposites show higher thermal stability than pristine PF as anchorage of nanoclay in PF matrix occur through the electrostatic interaction between nanoclay and polymer. The decrease in Si-O-Si stretching frequency during exfoliation is much higher than in intercalation, as Si-O-Si experience lesser hindrance to vibrate in exfoliated MMT galleries. The gradual redshift of π-π(*) transition peak of PF with increasing MMT content in composites confirms the uncoiling of PF in clay galleries. The photoluminescence characteristics reveal interruption of interchain interaction in this intercalated and exfoliated organic/inorganic hybrid system, which reduces the low-energy emission that results from keto defect. Due to very high aspect ratio of MMT, it can act as an efficient exciton blocking layer and a barrier to oxygen diffusion, which may lead to a device with high color purity and enhanced photostability. Again current-voltage characteristics of nanocomposite films confirm the retention of LED properties after nanocomposite formation.     

Effective preparation of montmorillonite/polyurethane nanocomposites by introducing cationic groups into the polyurethane main chain

In this study, the effect of introducing a small amount of cationic groups into the polymer main chain on the exfoliation of montmorillonite (MMT) and the physical properties of the subsequent MMT/polymer nanocomposites were investigated. As a matrix polymer, a polyurethane cationomer (PUC) containing 3 mol% of quaternary ammonium groups was synthesized and MMT/PUC nanocomposites containing various amounts of MMT were prepared by the solution intercalation method. From the WAXS and TEM analyses, it was found that the MMT layers were completely exfoliated and dispersed in the PUC matrix. The Young’s modulus of the MMT/PUC nanocomposites significantly increased with increasing MMT content, but their elongation at break and maximum stress were maintained at a level close to that of the PU only at an MMT content of 1 wt% and decreased as the content of MMT increased above this level. The phase separation of the MMT/PUC nanocomposites was retarded with increasing content of MMT, due to the strong interactions between the PUC chains and the exfoliated MMT layers. It was found that the presence of small amounts of cationic groups in the main chain of the matrix polymer was very effective in facilitating the preparation of the MMT/polymer nanocomposites.     

Preparation and characterization of poly(butylene terephthalate) nanocomposites from thermally stable organic-modified montmorillonite

In this paper, cetyl pyridium chloride (CPC) was employed to modify the montmorillonite. TGA analysis shows that the organic modified clay has higher thermal stability than hexadecyl trimethyl ammonium chloride modified montmorillonite and is suitable to be used for preparing poly(butylene terephthalate) (PBT)/clay nanocomposites at the high temperature. And then PBT/clay nanocomposites were prepared by direct melt intercalation. The results of XRD, TEM and HREM experiments show the formation of exfoliated-intercalated structure. The thermal stability of the nanocomposites does not evidently decrease, but the char residue at 600 °C remarkably increase compared with pure PBT. DSC results indicate that clay improves the melting temperature, the crystallization rate and crystallinity of the PBT molecules in the nanocomposites.     

Preparation of poly(ethylene terephthalate)/organoclay nanocomposites using a polyester ionomer as a compatibilizer

In this work, poly(ethylene terephthalate)/organically modified montmorillonite (PET/o‐MMT) nanocomposites were prepared via direct melt compounding in a twin‐screw extruder. The main objective was to study the effects of using a polyester ionomer (PETi) as a compatibilizer to promote the intercalation and/or exfoliation of the o‐MMT in the PET. The o‐MMT content was 0, 1, 3, or 5 wt % and the PETi/o‐MMT mass ratio was 0/1, 1/1, or 3/1. The PETi was efficient to promote the intercalation/exfoliation of the o‐MMT in the PET matrix, as revealed by wide angle X‐ray scattering and transmission electron microscopy. Rheological characterization showed that the PET/o‐MMT nanocomposites exhibited a higher complex viscosity at low frequencies than PET, which is characteristic of materials presenting yield strength. Moreover, the higher the content and/or the degree of intercalation/exfoliation of the o‐MMT, the more the nanocomposite behaved like a solid because of a percolated structure formed by the o‐MMT layers, and the more the storage and loss modulus, G′ and G″, became independent of the frequency at low frequencies. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3084–3091, 2007     

The influence of a quaternary ammonium salt and MMT on the in situ intercalative polymerization of PMMA

Poly(methylmetacrylate)/montmorillonite (PMMA)/(MMT) nanocomposites were prepared by a one-step in situ intercalative solution polymerization involving the simultaneous modification of the MMT with a quaternary ammonium salt (cetyl-trimethylammonium bromide (CTMAB)), polymerization and polymer intercalation. Using benzoyl peroxide as an initiator, intercalated nanocomposites were formed and characterized by NMR, DSC, TGA, XRD, TEM and SEC. It was observed that it was not the MMT, but rather the CTMAB, that influences the polymerization reaction, especially the reaction yield, the molar mass averages and the molar mass distribution of the PMMA. The thermal stability of the PMMA was improved by the addition of both the MMT and/or the CTMAB.     

Preparation and nonisothermal crystallization behavior of polyamide 6/montmorillonite nanocomposites

Polyamide 6 (PA6)/montmorillonite (MMT) nanocomposites were prepared via melt intercalation. The structure, mechanical properties, and nonisothermal crystallization kinetics of PA6/MMT nanocomposites were investigated by X‐ray diffraction (XRD), tensile and impact tests, and differential scanning calorimetry (DSC). Before melt compounding, MMT was treated with an organic surfactant agent. XRD traces showed that PA6 crystallizes exclusively in γ‐crystalline structure within the nanocomposites. Tensile measurements showed that the MMT additions are beneficial in improving the strength and the stiffness of PA6, at the expense of tensile ductility. Impact tests revealed that the impact strength of PA6/MMT nanocomposites tended to decrease with increasing MMT content. The nonisothermal crystallization DSC data were analyzed by Avrami, Ozawa, modified Avrami‐Ozawa, and Nedkov methods. The validity of these empirical equations on the nonisothermal crystallization process of PA6/MMT nanocomposites is discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2878–2891, 2004     

Influence of Fe‐MMT on crosslinking and thermal degradation in silicone rubber/clay nanocomposites

In this article, silicone rubber (SR)/clay nanocomposites were synthesized by a melt‐intercalation process using synthetic Fe‐montmorillonite (Fe‐MMT) and natural Na‐MMT which were modified by cetyltrimethyl ammonium bromide (CTAB). This study has been designed to determine if the presence of structural iron in the matrix can result in radical trapping and then enhance thermal stability, affect the crosslinking degree and elongation. The SR/clay nanocomposites were characterized by X‐ray diffraction (XRD) patterns and transmission electron microscopy (TEM). Exfoliated and intercalated nanocomposites were obtained. Thermo gravimetric analysis (TGA) and mechanical performance were applied to test the properties of the SR/clay nanocomposites. The presence of iron significantly increased the onset temperature of thermal degradation in SR/Fe‐MMT nanocomposites. The thermal stability, gel fraction and mechanical property of SR/Fe‐MMT were different from the SR/Na‐MMT nanocomposites. So the iron not only in thermal degradation but in the vulcanization process acted as an antioxidant and radicals trap. Copyright © 2006 John Wiley & Sons, Ltd.     

SYNTHESIS AND CHARACTERIZATION OF ORGANOMONTMORILLONITE AND POLYAMIDE 66/MONTMORILLONITE NANOCOMPOSITES

The montmorillonites (MMTs), layered, smectite-type silicates, were premodified by two different methods priorto the polymer melt intercalation. In one case MMTs were modified with cetyltrimethylammonium bromide (CTAB), andtermed as organomontmorillonites (OMMTs); in the other case MMTs were modified by nylon, and the products were calledmodified montmorillonites (MMMTs). The effects of CTAB and nylon on the MMTs were investigated by using TG andWAXD. The results show that interlayer spacings of CTAN and nylon modified MMTs are larger than that of sodium MMTs.Then, polyamide 66 (PA 66)/MMT nanocomposites were obtained through the method of melt intercalation of polymers. Thenanocomposites were characterized by WAXD, TEM and Molau experiments. The results indicate that the MMTs dispersehomogeneously in the PA 66 matrix. The mechanical properties of nanocomposites, such as tensile properties and flexuralproperties, were also measured and show a tendency to increase with increase of MMT content and reach the maximumvalues at 5phr MMT content. The heat distortion temperature (HDT) of the nanocomposites (7 phr) is about 32 K higher thanthat of pure PA 66.     

Preparation and properties of PU/MCMMT nanocomposites

The cetyltrimethyl ammonium bromide (CTAB) was used as a swelling agent to be intercalated into the galleries of the montmorillonite (MMT) platelets to get the organic MMT (CMMT). Then 4,4′‐diphenylmethane diisocyanate (MDI) were grafted on CMMT by the reaction between hydroxyls in organic MMT platelets and MDI to synthesize the MDI modified CMMT (MCMMT). Polyurethane (PU)/MCMMT composites were prepared by situ polymerization. The MCMMT platelets dispersed in a PU matrix in nanometer scale. The dispersion and intercalation degree of the MCMMT platelets decreased with increase in the content of MCMMT. Under the same content of fillers, the tensile strength and tear strength of PU/MCMMT nanocomposites were higher than those of PU/organic MMT nanocomposites. The reinforcing effect of the MCMMT platelets to the PU was better than that of the organic MMT platelets. With increase in the content of MCMMT, the tensile strength and tear strength of the PU/MCMMT nanocomposites were increased, while the extent of the increase slowed down. Compared with those of PU, the thermal stability of PU/MCMMT nanocomposites was increased. Copyright © 2009 John Wiley & Sons, Ltd.     

Preparation of poly(propylene)/clay layered nanocomposites by melt intercalation from pristine montmorillonite (MMT)

Poly(propylene)/clay nanocomposites were prepared by melt intercalation, using pristine montmorillonite (MMT), hexadecyl trimethyl ammonium bromide (C16), poly(propylene) (PP) and maleic acid (MA) modified PP (MAPP), The nanocomposites structure is demonstrated using X‐ray diffraction (XRD) and high resolution electronic microscopy (HREM). Our purpose is to provide a general concept for manufacturing polymer nanocomposites by melt intercalation starting from the pristine MMT. We found different kneaders (twin‐screw extruder or twin‐roll mill) have influence on the morphology of the PP/clay nanocomposites. Thermogravimetric analysis (TGA) shows that the thermal stability of PP/clay nanocomposites has been improved compared with that of pure PP. Copyright © 2003 John Wiley & Sons, Ltd.     

Shear‐induced change of exfoliation and orientation in polypropylene/montmorillonite nanocomposites

For the improved dispersion of montmorillonite (MMT) in a polypropylene (PP) matrix, PP/MMT nanocomposites prepared via direct melt intercalation were further subjected to oscillating stress achieved by dynamic packing injection molding. The shear‐induced morphological changes were investigated with an Instron machine, wide‐angle X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. The original nanocomposites possessed a partly intercalated and partly exfoliated morphology. A transformation of the intercalated structure into an exfoliated structure occurred after shearing, and a more homogeneous dispersion of MMT in the PP matrix was obtained. However, the increase of the exfoliated structure was accompanied by the scarifying of the orientation of MMT layers along the shear direction. Some bended or curved MMT layers were found for the first time by TEM after shearing. However, the orientation of PP chains in the PP/MMT nanocomposites became very difficult under an external shear force; this indicated that the molecular motion of PP chains intercalated between MMT layers was highly confined. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1–10, 2003     

聚乙烯醇/氟基蒙脱土纳米复合材料的合成及性能研究

采用水热方法,在493 K条件下反应72小时,合成了氟基蒙脱土(F-MMT),在这种F-MMT中,硅酸盐结构中的一些OH-被F-取代。采用溶液插层方法,制备了聚乙烯醇/F-MMT纳米复合材料(PVA/F-MMT)。采用X 射线衍射、扫描电镜和透射电镜对F-MMT 和 PVA/F-MMT纳米复合材料进行了表征;结果表明,片状结构的F-MMT均匀分散于PVA中,形成了层离结构的纳米复合材料。热重分析、力学性能和紫外可见光谱的测试结果表明,在没有牺牲光学性能情况下,PVA/F-MMT纳米复合材料的热稳定性和力学性能都得到了提高。力学和热学性能的提高归功于F-MMT均匀而好的分散于聚合物基体中,以及PVA中的 OH- 和F-MMT 中F-之间强的氢键作用。     

Synergistic flammability and thermal stability of polypropylene/aluminum trihydroxide/Fe‐montmorillonite nanocomposites

In the present study, polypropylene/aluminium trihydroxide/Fe‐montmorillonite (PP/ATH/Fe‐MMT) nanocomposites were prepared by melt‐intercalation method. This was been designed to determine whether the presence of structural iron in the matrix could enhance the thermal stability and flammability of nanocomposites. In order to prove the effect of Fe³⁺ in the structural silicate layers, samples of PP/ATH and PP/ATH/Na‐MMT (no Fe³⁺ in structural silicate layers) were prepared under the same conditions. Fe‐MMT and Na‐MMT were modified by cetyltrimethyl ammonium bromide (CTAB). The nanocomposite structures were characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), and thermogravimetric analysis (TGA) was applied to test the thermal properties of nanocomposites. In addition, the limiting oxygen index (LOI) of PP/ATH/Fe‐MMT nanocomposites was increased, and no dripping phenomenon was found through the UL‐94 vertical burning test. Copyright © 2009 John Wiley & Sons, Ltd.     

Exploitation of introducing of catalytic centers into layer galleries of layered silicates and related epoxy nanocomposites. I. Epoxy nanocomposites derived from montmorillonite modified with catalytic surfactant‐bearing carboxyl groups

Montmorillonite (MMT) was modified with the acidified cocamidopropyl betaine (CAB) and the resulting organo‐montmorillonite (O‐MMT) was dispersed in an epoxy/methyl tetrahydrophthalic anhydride system to form epoxy nanocomposites. The intercalation and exfoliation behavior of the epoxy nanocomposites were examined by X‐ray diffraction and transmission electron microscopy. The curing behavior and thermal property were investigated by in situ Fourier transform infrared spectroscopy and DSC, respectively. The results showed that MMT could be highly intercalated by acidified CAB, and O‐MMT could be easily dispersed in epoxy resin to form intercalated/exfoliated epoxy nanocomposites. When the O‐MMT loading was lower than 8 phr (relative to 100 phr resin), exfoliated nanocomposites were achieved. The glass‐transition temperatures (T_g's) of the exfoliated nanocomposite were 20 °C higher than that of the neat resin. At higher O‐MMT loading, partial exfoliation was achieved, and those samples possessed moderately higher T_g's as compared with the neat resin. O‐MMT showed an obviously catalytic nature toward the curing of epoxy resin. The curing rate of the epoxy compound increased with O‐MMT loading. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1192–1198, 2004     

乳液聚合法制备剥离型PS/MMT纳米复合材料

以阳离子表面活性剂十八烷基三甲基氯化铵(OTAC)和烯丙基十八烷基二甲基氯化铵(ATAC)为插层处理剂改性蒙脱土(MMT),原位乳液聚合分别制备了PS/C18MMT和PS/AC18MMT两种纳米复合材料.XRD和TEM分析表明,MMT均被剥离成单个或几个片层无规的分散在PS基体中,TGA分析表明,MMT的加入提高了材料的耐热性能,当PS基体与有机化处理的MMT片层发生一定的化学连接后,PS/AC18MMT纳米复合材料表现出更好的耐热性能.动态力学分析表明,MMT的加入提高了PS的玻璃态储能模量,降低了材料的动态损耗;PS/AC18MMT纳米复合材料的玻璃化温度较PS有所提高,而PS/C18MMT的玻璃化温度与PS相比略有降低.     

Characterization and thermal degradation studies on polyaniline‐intercalated montmorillonite nanocomposites prepared by a solvent‐free mechanochemical route

Polyaniline (PANI)‐montmorillonite (MMT) nanocomposites were prepared by direct intercalation of aniline molecules into MMT galleries, followed by in situ polymerization within the nano‐interlamellar spaces under solvent‐free conditions. The basal spacing of aniline‐intercalated MMT increased gradually up to 1.5 nm with increasing amounts of aniline loaded. This result suggests that aniline molecules were adsorbed by MMT clay and that intercalated aniline likely located perpendicular to the silicate sheets. After polymerization, X‐ray diffraction and Fourier transform infrared analyses confirmed the successful synthesis of PANI chains between the MMT nano‐interlayers. The scanning electron microscopy images indicated that the surface morphologies of PANI–MMTs were strongly different depending on the PANI content. The electrical conductivities of PANI nanocomposite particles in pressed pellets ranged in the order of between 10^?3 and 10^?2 S/cm. UV–vis spectroscopy and doping level measurement were further used to discuss the conductivities of nanocomposites. The thermal stabilities of PANI–MMT nanocomposites were examined by using thermogravimetric‐differential thermal analysis and derivative thermogravimetric analysis, and both analyses consequently demonstrated the improved thermal stabilities of the PANI chains in the nanocomposites as compared to pure PANI. The thermal stabilities of resulting nanocomposites were strongly related to the PANI content, which increased as the PANI content decreased in the nanocomposites. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2705–2714, 2005