Preparation of a Novel COOH Ion Implantation Sensor and Its Application

A novel ion implantation sensor (DNA/COOH/ITO) based on DNA immobilization in COOH/ITO probe was manufactured for the first time. The surface morphologies of the electrodes were characterized by X‐ray photoelectron spectroscopy (XPS), field‐emission‐scanning electron microscopy (FSEM) and electrochemical methods. In a 0.5 mol/L PBS solution, a sensitive oxidation peak of DNA on the COOH/ITO electrode was obtained by voltammetry. The electrochemical behavior of DNA was studied. And the oxidative peak potential of DNA was +0.400 V (vs. Ag/AgCl). Its peak current was proportional to the concentration of DNA over the range of 1.0×10^?8?1.0×10^?6 mol/L with a detection limit of 5.0×10^?9 mol/L (about 0.5 ng/mL). This sensor was applied to the direct detection of DNA samples.     

Electrochemical Studies of the Interaction of 2‐Nitroacridone with DNA and Determination of DNA

A new acridone derivate 2‐nitroacridone (NAD) was synthesized and a new method of electrochemical probe has been proposed for the determination of salmon sperm DNA based on its interaction with NAD. The electrochemical behavior of interaction of NAD with DNA was investigated on glassy carbon electrode (GCE). In the presence of DNA, the peak current of NAD decreases and the peak potential shifts to a more positive potential without appearance of a new peak. The binding ratio between NAD and salmon sperm DNA was calculated to be 2 : 1 and the binding constant was 3.19×10⁵ L/mol. The decrease of the peak current (ΔI_p) of NAD was proportional to the concentration of DNA in the range from 1.55×10^?7 M to 2.02×10^?6 M with the detection limit of 3.10×10^?8 M, and DNA of synthetic sample was determined satisfactorily. Additionally, the binding mechanism was preliminarily discussed. The mode of interaction between NAD and DNA was found to be intercalation binding.     

Electrochemical and Spectroscopic Studies on the Interaction of Gallocyanine with DNA

The interaction of gallocyanine (GC) with double‐stranded DNA (dsDNA) in pH 3.5 Tris‐HCl buffer solution was investigated by electrochemical methods and spectrophotometric methods as well. In the potential scan range of ‐0.25 ? +0.18 V(vs. SCE), GC had a couple of well‐defined redox peaks at ‐0.022 V and ‐0.069 V on a cyclic voltammogram at the scan rate of 100.0 mV/s, respectively. After the addition of dsDNA into the GC solution, the redox‐peak currents decreased obviously and the peak potentials shifted positively. The results demonstrated that GC binding to DNA was caused by intercalation. Electrochemical parameters such as the electron number (n), the charge transfer coefficient (α) and the electrochemical reaction standard rate constant (k_s) were calculated and compared in the absence and presence of dsDNA. Almost unchanged values of the electrochemical parameters after adding dsDNA showed that non‐electroactive complexes were formed when GC interacted with DNA. The results indicated that the decrease of the redox‐peak currents was caused by the decrease of the free concentration of GC in the reaction solution. The binding constant and binding ratio were investigated by spectrophotometric methods. DNA concentration can be determined by the decrease of the peak current of GC. The linear range for dsDNA was in the range of 1.45 × 10^?7 ? 1.45 × 10^?6mol/Land 1.45 × 10^?6 ? 1.45 × 10^?5 mol/L, respectively with the linear regression equation as Δi_P (10^?7 A) = 0.037 + 0.018C (10^?7mol/L), and Δi_P (10^?7 A) = 0.25 + 0.041C (10^?6mol/L), respectively, and the detection limit (3σ) was 1.13 × 10^?7 mol/L.     

Label-Free Detection of DNA Hybridization Based on MnO2 Nanoparticles

Abstract

Nano-MnO₂/chitosan composite film modified glassy carbon electrode (MnO₂/CHIT/GCE) was fabricated and a DNA probe was immobilized on the electrode surface. The immobilization and hybridization events of DNA were characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The EIS was applied to the label-free detection of the target DNA. The human immunodeficiency virus (HIV) gene fragment was successfully detected by this DNA electrochemical sensor. The dynamic detection range was from 2.0 × 10^?11 to 2.0 × 10^?6 mol/L, with a detection limit of 1.0 × 10^?12 mol/L.     

The electrochemical oxidation of pentachlorophenol and its sensitive determination at chitosan modified carbon paste electrode

We report on a novel electrochemical method to detect trace pentachlorophenol (PCP) by using a chitosan (CS) modified carbon paste electrode (CS/CPE). Compared with that at a bare carbon paste electrode (CPE), the current response was greatly improved at the CS/CPE due to the enhancement effect of CS. Under optimal working conditions, the oxidation peak current of PCP was proportional to its concentration in the range of 1.0 × 10^?7 to 5.0 × 10^?6 and 5.0 × 10^?6 to 1.0 × 10^?4 mol/L, with an extremely low detection limit of 4.0 × 10^?8 mol/L. Our method was successfully used to detect the PCP concentration in vegetable samples.     

碳纳米管修饰金电极检测特定序列DNA

利用化学偶联法将末端修饰氨基的寡聚核苷酸固定在表面修饰有羧基化碳纳米管(CNTs-COOH)的金电极表面, 制备新型核酸探针, 可以特异性结合目标单链寡聚核苷酸. 以阿霉素作为嵌合指示剂, 利用示差脉冲法测定杂交的结果. 经过实验条件的优化, 测定DNA浓度在1.0×10^－6～1.0×10^－9 mol/L呈良好的线性关系. 检测限为: 2.54×10^－10 mol/L. 碳纳米管特有的纳米结构对检测结果的放大作用, 提高了该传感器的检测限和灵敏度.     

Hole transport of trans-1,2-biscarbazolylcyclobutane-doped poly(bisphenol A carbonate) film

The hole transport of trans-1,2-biscarbazolylcyclobutane (CB) doped poly(bisphenol A carbonate) (PC) film has been investigated in the CB concentration range of 3.8 × 10^?4 mol cm^?3 (12 wt%) to 1.6 × 10^?3 mol cm^?3 (51 wt%). The hole mobility increased drastically with increasing CB concentration. The hole mobility was analyzed by a random hopping model. The localization radius ρ₀ of the CB/PC system was 1.9 Å, which is larger than that obtained for the N-isopropyl-carbazole-doped PC system. This suggests that the larger localization radius of the CB/PC system is related to the larger spatial extent of the CB molecule. The highest hole mobility of 2.9 × 10^?6 cm² V^?1 s^?1 was obtained when the CB concentration was 1.6 × 10^?3 mol cm^?3 (51 wt%) at E = 1.6 × 10⁵ V cm^?1 and T = 298 K. This mobility is about 10 times higher than that of poly(N-vinylcarbazole) (PVCz). The activation energy of hole mobility for the CB/PC system decreased with increasing CB concentration and was 0.31 eV at 51 wt% of CB, which is lower than the 0.45 eV for PVCz. The low activation energy for the CB/PC system is ascribed to the absence of an excimer-forming site that works as a multiple-trapping site for hole carriers.     

Study on the Electrochemical Behavior of Dopamine and Uric Acid at a 2‐Amino‐5‐mercapto‐[1,3,4] Triazole Self‐Assembled Monolayers Electrode

Selected from a series of structurally related heteroaromatic thiols, a newly synthesized reagent 2‐amino‐5‐mercapto‐[1,3,4] triazole (MATZ) was used to fabricate self‐assembled monolayers (SAMs) on gold electrode for the first time. The MATZ/Au SAMs was characterized by electrochemical methods and scanning electronic microscopy (SEM). In 0.04 mol/L Britton–Robinson buffer solution (pH 5), the electrochemical behavior of dopamine showed a quasireversible process at the MATZ/Au SAMs with an electrode kinetic constant 0.1049 cm/s. However, the electrochemical reaction of uric acid at the SAMs electrode showed an irreversible oxidation process, the charge‐transfer kinetics of uric acid was promoted by the SAMs. By Osteryoung square‐wave voltammetry (OSWV), the simultaneous determination of dopamine and uric acid can be accomplished with an oxidation peak separation of 0.24 V, the peak current of dopamine and uric acid were linearly to its concentration in the range of 2.5×10^?6–5.0×10^?4 mol/L for dopamine and 1×10^?6–1×10^?4 mol/L for uric acid with a detection limit of 8.0×10^?7 mol/L for dopamine and 7.0×10^?7 mol/L for uric acid. The MATZ/Au SAMs electrode was used to detect the content of uric acid in real urine and serum sample with satisfactory results.     

Electrochemical DNA Biosensor Based on Partially Reduced Graphene Oxide Modified Carbon Ionic Liquid Electrode for the Detection of Transgenic Soybean A2704‐12 Gene Sequence

In this work a partially reduced graphene oxide (p‐RGO) modified carbon ionic liquid electrode (CILE) was prepared as the platform to fabricate an electrochemical DNA sensor, which was used for the sensitive detection of target ssDNA sequence related to transgenic soybean A2704‐12 sequence. The CILE was fabricated by using 1‐butylpyridinium hexafluorophosphate as the binder and then p‐RGO was deposited on the surface of CILE by controlling the electroreduction conditions. NH₂ modified ssDNA probe sequences were immobilized on the electrode surface via covalent bonds between the unreduced oxygen groups on the p‐RGO surface and the amine group at the 5′‐end of ssDNA, which was denoted as ssDNA/p‐RGO/CILE and further used to hybridize with the target ssDNA sequence. Methylene blue (MB) was used as electrochemical indicator to monitor the DNA hybridization. The reduction peak current of MB after hybridization was proportional to the concentration of target A2704‐12 ssDNA sequences in the range from 1.0×10^?12 to 1.0×10^?6 mol/L with a detection limit of 2.9×10^?13 mol/L (3σ). The electrochemical DNA biosensor was further used for the detection of PCR products of transgenic soybean with satisfactory results.     

荧光光谱法研究核黄素与鲱鱼精DNA的相互作用

在B-R缓冲溶液中, 以吖啶橙(AO)作荧光探针研究了核黄素(RF)与DNA的相互作用. 在pH值为7.25时, 荧光光谱研究表明, RF与DNA发生作用生成了复合物, 其结合比为n_RF∶n_DNA＝5∶1, 28 ℃时RF与DNA的结合常数K＝2.53×10⁶ L/mol; 并运用双倒数法求得RF与DNA相互作用的 为－6.06×10⁴ J/mol, 为－78.70 J/(mol•K), 28 ℃时的 为－3.69×10⁴ J/mol. 同时通过粘度法、盐效应和Scatchard法等研究了RF与DNA的作用方式, 确定了在该实验条件下RF与鲱鱼精DNA之间主要为沟面和静电作用方式.     

7-甲基鸟苷在玻碳电极上的伏安行为研究

研究了修饰核苷7-甲基鸟苷(7-Methylguanosine)的电化学行为及测定方法.在pH 1.98的B-R缓冲液中,用循环伏安法(CV),线性扫描伏安法(LSV)、微分脉冲伏安法(DPV)等现代电化学技术研究7-甲基鸟苷在玻碳电极(GCE)上的伏安行为.实验表明,7-甲基鸟苷在 1.036 V(vs.SCE)电位处产生一个阳极氧化峰,峰电流与7-甲基鸟苷的浓度在5.0×10-5-2.0×10-6mol/L范围内呈良好的线性关系,最低检测限(D=2σ/K)为4.1×10-7mol/L.并用恒电位库仑电解法等方法对其氧化机理进行了较为详细的探讨,得到了可能的电极反应机理:7-甲基鸟苷在玻碳电极上的电极反应是属于失1质子和2电子的不可逆的氧化反应.     

An Ultrasensitive Analytical Method Based on Chemiluminescence Sensing Electrochemical Parallel Catalytic Reaction Event

An ultrasensitive electrochemiluminescence (ECL) method on the combination of electrochemical parallel catalytic reaction and chemiluminesence signal sensing was proposed for improving ECL analytical characteristics using vanadate(V) as a representative. Vanadate(V) could be electrochemically reduced to generate vanadate(II) which could be chemically oxidized by potassium periodate to regenerate vanadate(V) and give parallel catalytic wave effect. Then, the reduced product of potassium periodate could react with butyl‐rhodamine B to emit a sensitive chemiluminescence signal. The chemiluminescence intensity was correlative with vanadate(V) concentration. The investigation on the electrochemical reaction rate constant (k⁰) confirmed that the speed of electrochemical reaction was faster than that of the subsequent chemiluminescence reaction. The possibility of the combination of electrochemical parallel catalytic reaction with chemiluminescence signal sensing was proved. The similar ECL behaviors could be observed at zirconia nanowires‐Nafion modified electrode. Because of the separation and enrichment effect of the modified electrode on vanadate(V), the selectivity and sensitivity was further improved greatly. Based on these findings, a new concept on the combination of electrochemical parallel catalytic reaction and chemiluminesence signal sensing was proposed and an ultrasensitive ECL method for the determination of vanadate(V) was developed at zirconia nanowires‐Nafion modified electrode. Under the optimum experimental conditions, the ECL intensity was linear with the concentration of vanadate(V) in the range of 2.0×10^?12 mol/L–2.0×10^?10 mol/L. The detection limit was 8.0×10^?13 mol/L, which was more than 6 orders of magnitude lower than that observed by electrochemical current transduction for electrochemical parallel catalytic reaction at zirconia nanowires‐Nafion modified electrode.     

Electrochemical DNA Biosensor Based on Graphene and TiO2 Nanorods Composite Film for the Detection of Transgenic Soybean Gene Sequence of MON89788

Based on graphene (GR), TiO₂ nanorods, and chitosan (CTS) nanocomposite modified carbon ionic liquid electrode (CILE) as substrate electrode, a new electrochemical DNA biosensor was effectively fabricated for the detection of the transgenic soybean sequence of MON89788. By using methylene blue (MB) as hybridization indicator for monitoring the hybridization with different ssDNA sequences, the differential pulse voltammetric response of MB on DNA modified electrodes were recorded and compared. Due to the synergistic effects of TiO₂ nanorods and GR on the electrode surface, the electrochemical responses of MB were greatly increased. Under optimal conditions the differential pulse voltammetric response of the target ssDNA sequence could be detected in the range from 1.0×10^?12 to 1.0×10^?6 mol/L with a detection limit of 7.21×10^?13 mol/L (3σ). This electrochemical DNA biosensor was further applied to the polymerase chain reaction (PCR) product of transgenic soybeans with satisfactory results.     

Study on Diffusion Mechanisms and Determination of Dihydroxybenzene Isomers at the Pre‐anodized Inlaying Ultrathin Carbon Paste Electrode

In this paper, nichrome was adopted as a substrate, to fabricate the pre‐anodized inlaying ultrathin carbon paste electrode (PAIUCPE). The electrochemical behaviors and diffusion mechanisms of three dihydroxybenzene isomers at the electrode were carefully investigated. The effect of pH on oxidation peak current was also detailedly explained. The results were shown that oxidation peak current not only related to the reaction of electroactive materials at the working electrode, but also depended on the reaction variable of reduction at the auxiliary electrode. The oxidation peaks of hydroquinone (HQ), catechol (CC) and resorcinol (RC) located at 0.181 V, 0.288 V and 0.736 V. For CC, RC and HQ, the oxidation peak currents were linear to the concentrations at the range of 5.0 × 10^?6～5.0 × 10^?4 mol/L, 3.0 × 10^?6～5.0 × 10^?4 mol/L and 4.0 × 10^?6～4.0 × 10^?4 mol/L with the detection limits of 2.0 × 10^?7 mol/L, 1.2 × 10^?7 mol/L and 1.2 × 10^?7 mol/L, respectively. The proposed method was successfully applied in the simultaneous determination of dihydroxybenzene isomers in artificial sewage samples with satisfactory results.     

氮掺杂碳纳米管修饰电极的电化学行为

制备了氮掺杂改性的碳纳米管, 并用循环伏安法(CV)测定了多巴胺(DA)和抗坏血酸(AA)在不同氮含量的碳纳米管修饰电极上的电化学行为. 结果表明, 氮掺杂碳纳米管修饰电极对AA和DA有不同的电催化行为, 其中高氮含量修饰电极对AA的催化作用强, 而低氮含量修饰电极对DA的催化作用强. 微分脉冲伏安法(DPV)的结果显示, DA的氧化峰电流与其浓度在5.0×10^－6～2.0×10^－4 mol/L范围内呈良好的线性关系, 检出限达1.64×10^－6 mol/L (S/N＝3); AA氧化峰电流与其浓度在3.0×10^－5～1.0×10^－2 mol/L范围内呈良好的线性关系, 检出限达3.26×10^－6 mol/L (S/N＝3). 该修饰电极在AA大量存在(AA浓度为DA浓度两万倍)时可选择性地实现多巴胺的测定而不造成干扰.     

A Nitric Oxide Biosensor Based on Myoglobin Adsorbed on Multi‐Walled Carbon Nanotubes

Myoglobin (Myb) of horse heart is incorporated on multi‐walled carbon nanotubes (MWNTs) and immobilized at a glassy carbon (GC) electrode surface. Its electrochemical behavior and enzyme activity are characterized by employing electrochemical methods. The results indicate that MWNTs can obviously promote the direct electron transfer between Myb and electrode, and that the Myb on MWNTs behaves as an enzyme‐like activity towards the electrochemical reduction of nitric oxide (NO). Accordingly, an unmediated NO biosensor is constructed. Experimental results reveal that the peak current related to NO is linearly proportional to its concentration in the range of 2.0×10^?7–4.0×10^?5 mol/L. The detection limit is estimated to be 8.0×10^?8 mol/L. Considering a relative standard deviation of 2.1% in seven independent determinations of 1.0×10^?5 mol/L NO, this biosensor shows a good reproducibility. The biosensor based on Myb/MWNTs modified electrode can be used for the rapid determination of trace NO in aqueous solution with a good stability, nice selectivity and easy construction.     

Molecularly Imprinted Electrochemical Luminescence Sensor Based on Enzymatic Amplification for Ultratrace Isoproturon Determination

A new molecularly imprinted electrochemical luminescence sensor (MIP‐ECL sensor) was developed for isoproturon (IPU) determination based on the competition reaction between IPU and glucose oxidase labeled IPU (GOD‐IPU). After competition, hydrogen peroxide produced by residual GOD‐IPU on the MIP reacted with luminol to emit electrochemiluminescence (ECL) signal. The ECL intensity decreased when the GOD‐IPU molecules were replaced by IPU molecules in the samples. IPU could be determined in the concentration range from 9×10^?11 mol/L to 5.1×10^?9 mol/L with a detection limit of 3.78×10^?12 mol/L. Water samples were assayed and recoveries ranging from 98.5 % to 102.1 % were obtained.     

Voltammetric Characterisation of Anticancer Drug Irinotecan

Electrochemical reduction of irinotecan was investigated on a static mercury drop electrode using square‐wave voltammetry. The mechanism of irinotecan electroreduction is a complex, pH‐dependent, quasireversible process and includes the transfer of two electrons and two protons. In acidic medium, the first electron transfer reaction is followed by the chemical reaction, and the product of this chemical reaction undergoes further electrochemical reduction at more negative potentials. Both irinotecan and the product of its reduction adsorb on the mercury electrode surface. Based on the adsorptive character of irinotecan, a new adsorptive stripping square‐wave voltammetric method for its electroanalytical determination has been proposed. The voltammetric response could be used to determine irinotecan in the concentration range from 1×10⁻⁷ mol/L to 1.5×10⁻⁶ mol/L and from 5×10⁻⁹ mol/L to 1.2×10⁻⁷ mol/L, if the accumulation time is 20 s and 300 s, respectively. The calculated limit of detection for irinotecan was found to be 8.7×10⁻⁹ mol/L (if t_acc=300 s).     

Chiral Recognition of Penicillamine Enantiomers Based on DNA‐MWNT Complex Modified Electrode

Double‐stranded DNA and multiwalled carbon nanotube (MWNT) complex modified glassy carbon electrodes (DNA‐MWNT‐GCE) were employed to discriminate penicillamine (PA) enantiomers. Cyclic voltammetry, electrochemical impedance spectroscopy, atomic force microscopy and ultraviolet‐visible spectroscopy were used to characterize the enantioselective phenomenon. The results indicated that the binding effect between L ‐PA and DNA‐MWNTs was stronger than that of D ‐PA and DNA‐MWNTs. In addition, the influencing factors of the modified electrodes were systematically investigated. The modified electrodes exhibited a linear response towards PA enantiomers from 1.0×10^?1 to 1.0×10^?8 mol L^?1 and detection limits of 3.1×10^?9 and 3.3×10^?8 mol L^?1 for L ‐PA and D ‐PA, respectively.     

Nano Au/TiO2 hollow microsphere membranes for the improved sensitivity of detecting specific DNA sequences related to transgenes in transgenic plants

Gold nanoparticles (nano Au)/titanium dioxide (TiO₂) hollow microsphere membranes were prepared on the carbon paste electrode (CPE) for enhancing the sensitivity of DNA hybridization detection. The immobilization of nano Au and TiO₂ microsphere was investigated with cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The hybridization events were monitored with EIS using [Fe(CN)₆]^3?/4? as indicator. The sequence-specific DNA of the 35S promoter from cauliflower mosaic virus (CaMV35S) gene was detected with this DNA electrochemical sensor. The dynamic detection range was from 1.0×10^?12 to 1.0×10^?8 mol/L DNA and a detection limit of 2.3×10^?13 mol/L could be obtained. The polymerase chain reaction (PCR) amplification of the terminator of nopaline synthase (NOS) gene from the real sample of a kind of transgenic soybean was also satisfactorily detected.