空间频率对透射式全息图衍射率的影响

为研究干涉条纹空间频率与透射式全息图衍射率的关系,在相同条件下,拍摄以平面波、发散的和会聚的球面波分别作参考光、物光的透射式全息图,通过实验测量其衍射效率,同时计算了干涉条纹的空间频率。然后以会聚的球面波为物光,平面波为参考光,分别改变入射角和球面波会聚点到记录面的距离制作另外4块透射式全息图,并计算了它们的空间频率,测量了其衍射效率。结果表明：在相同条件下制作透射式全息图时,衍射效率只由空间频率决定,与使用何种参考光和物光无关,空间频率仅随参考光和物光的夹角变化而变化。     

球面波条件下体全息存储的衍射特性分析

从理论上推导了球面波作为参考光和读出光时体全息存储的相对衍射效率和晶体旋转角度之间的关系,对得到的衍射效率的理论公式进行了数值模拟,并且对模拟的结果进行了分析。结果表明,球面波系统的存储容量更高,角度选择性更好,并且有利于系统的小型化。     

衍射光学器件光线追迹公式的实验验证

本文介绍了一种衍射光学器件光线追迹的方法，并给出了计算公式。作为验证，在实验室里制作了具有连续相位的体全息器件，将其实际再现光斑与计算点列图进行比较。构造透射体全息片的物光为离轴的球面波，始于轴外点Ａ（０，１３２ｓｉｎ８°，－１３２ｃｏｓ８°），参考光为平面光束，其与Ｚ轴夹角为１７°。激光器采用氩离子激光器（Ｓｐｅｃｔｒａ－ｐｈｙｓｉｃｓＭｏｄｅｌ２０２０），波长４８８ｎｍ；干板感光胶为重铬酸明胶（ＤＣＧ），胶层厚为１５μｍ；通光口径３０ｎｍ。测试时把全息片放在干板的位置。挡住物光，让再现光以和参考光路相同的路径平行入射到全息片上，在全息片后垂直光轴放置毛玻璃片，平行光轴移动毛玻璃片，可观察到－１级衍射光的变化。在距离原点的距离分别为（ａ）４０ｍｍ，（ｂ）７０ｍｍ，（ｃ）８７ｍｍ，（ｄ）９５ｍｍ的地方用ＣＣＤ拍摄了衍射光的形状，与程序计算的点列图在形状和大小上都吻合     

分频光栅的衍射特性及误差分析

 基于标量衍射理论推导出了分频光栅的各级衍射效率公式，分析了分频光栅的衍射特性，发现入射光波在满足相应的相位延迟条件时，能被分频光栅以最大效率衍射进３个中央级次中的某一级。分析和比较了两种制作工艺中的刻蚀深度误差、占空比误差对衍射效率的影响。在惯性约束聚变（ICF）应用中，对于同一要求的３倍频光的衍射效率范围，两种工艺的刻蚀误差容限是相同的，但是两种工艺的相同刻蚀误差却带来不同的衍射效率。在不计其它误差时，占空比误差不会对３倍频光的衍射效率产生影响，但可以对基频光和2倍频光产生相反的影响，占空比误差还可以使基频光和2倍频光的主要衍射级次的效率都降低，同时增大它们的0级衍射效率。     

散射光彩色数字全息光学系统及波面重建算法研究

令物体表面为散射面,参考光及重建光为球面波,详细研究了离轴数字全息物光场重建平面的光波场.导出物光、共轭物光及零级衍射光分布与光学系统参数的关系.根据彩色数字全息的特点,提出抑制零级衍射干扰的光学系统设计方法,并且对一种能够避免插值误差的波面重建算法进行了优化研究,给出了相应的实验证明.     

菌紫质同线偏振全息记录时再现光偏振方向对衍射效率的调制

当用相同偏振方向的物光和参考光在菌紫质薄膜上记录光栅时,再现光的偏振方向会影响其衍射效率.采用琼斯矩阵方法对此进行了理论分析,结果显示,再现光的偏振方向对衍射光的光强产生余弦调制;当再现光的偏振方向平行或垂直于记录光的偏振方向时,衍射光仍为线偏振光,其他情况下衍射光均变成椭圆偏振光.再现光偏振方向对衍射效率峰值的调制为正向余弦调制,对衍射效率稳定值的调制为反向余弦调制(与前者在相位上相差π).加入辅助紫光可抑制光栅的饱和,从而使得再现光偏振对衍射效率稳定值的调制由反向余弦调制变为正向余弦调制,并且提高了衍 关键词： 菌紫质 光致各向异性 衍射效率 琼斯矩阵     

极紫外三维小孔矢量衍射波面质量分析

相移点衍射干涉仪中参考球面波的质量取决于小孔的直径、圆度和厚度,其中小孔的直径是最主要的因素,在实际加工前,需给出小孔直径的要求。基于矢量衍射理论,分析计算了三维结构小孔的衍射。分析了在均匀的TE偏振光和TM偏振光入射情况下,小孔直径大小对衍射波面质量的影响。入射光的线性偏振,给衍射波面中引入了像散和彗差。分析计算得出,为了获得数值孔径(NA)为0.1,相对于理想球面波的均方根(RMS)偏差不大于0.005λ(λ=13.55 nm),强度均匀性为0.4的参考球面波,对90 nm厚的小孔选择直径大小为70 nm较为适宜。     

大角带宽高衍射效率体全息光栅的设计和制备

高性能体全息光栅是全息波导的重要耦合元件,角带宽小、平均衍射效率不高是制约体全息光栅性能的重要因素。以不对称倾斜记录为出发点,设计并制备了大角带宽高衍射效率的体全息光栅。首先讨论在横电模式光和横磁模式光下体全息光栅的记录参数与其衍射效率的关系,找到平均衍射效率较高的记录参数范围,随后进一步分析在此范围内的记录参数与体全息光栅的角带宽的关系,从而确定获得大角带宽高衍射效率体全息光栅的最佳记录参数。实验结果表明:在参考光入射角度为25°、信号光入射角度为30°时,制备的体全息光栅的角带宽达到±14°,衍射效率为82%。     

圆锥透镜对偏轴球面波光束的衍射模式

球面波入射圆锥透镜产生的出射光束中心光斑直径较小且焦深长，适合通讯领域长距离测量和准直。针对实际操作中球面波光束入射时很可能与圆锥透镜的中心轴线发生偏移或倾斜，使衍射光场发生变化，着重研究圆锥透镜对偏轴球面波光束的衍射模式，并通过衍射理论和稳相法分析，研究其径向衍射光场的分布特性。使用半径为15mm，底角为1°的圆锥透镜进行计算机仿真和实验，最后将实验结果与理论分析和仿真结果相比较，证明球面波的曲率半径和出射光束的传输距离越小，偏轴对衍射模式的影响越小。该研究结果表明：在激光通讯等长距离通信中，使用曲率半径小的球面波光束代替平面波入射圆锥透镜，不仅可以扩展焦深，还可以降低偏轴对测量的影响。     

光横向传播的光折变体全息透镜设计及其衍射性质

提出了一种新型的可用于光束横向传播的光折变体全息透镜。该透镜是由入射方向相互垂直的一束平面波和一束球面波在双掺杂的铌酸锂晶体平板上记录形成的，它可以将垂直入射晶体平板的输入光束产生横向传输并聚焦，或对输入光点产生横传并准直输出。该透镜除了具有一般体全息透镜的稳定性好、可靠性高的特点外，特别具有光束横向传播的功能，因而具有空占比小、更易于整个光学透镜系统的微小化集成的优点。利用局域体全息的耦合波理论，计算了该透镜衍射光的振幅分布和衍射效率。计算了该透镜的焦面上的强度分布，并与理想球面波照射矩形孔径时焦面上的强度分布进行了比较。     

Cross-talk Noise Suppresion in Volume Holography with a Composite Reading Beam

ＣｒｏｓｔａｌｋＮｏｉｓｅＳｕｐｐｒｅｓｉｏｎｉｎＶｏｌｕｍｅＨｏｌｏｇｒａｐｈｙｗｉｔｈａＣｏｍｐｏｓｉｔｅＲｅａｄｉｎｇＢｅａｍＬＩＸｉａｏｃｈｕｎＷＵＭｉｎｘｉａｎＨＥＱｉｎｇｓｈｅｎｇＪＩＮＧｕｏｆａｎ（ＤｅｐａｒｔｍｅｎｔｏｆＰｒｅｃｉ...     

基于相位共轭的动态体全息衍射特性的实时非破坏性测量

基于相位共轭技术,提出了一种动态体全息衍射特性的实时测量方法.在光学系统设计中,通过调整使得物光和参考光较强,而与参考光共轭的再现光非常弱（约为参考光的1/1 000）,借助非常微弱的共轭再现光实现了动态体全息的非破坏性实时测量.三束光的强度和偏振态可通过1/4波片、偏振片和衰减片进行调节和组合,可记录光强调制型或偏振态调制型体全息.本方法适合于光致折射率变化和光致变色材料体全息的测量.     

Multiplexed phase-conjugate holographic data storage with a buffer hologram

We describe and demonstrate a volume holographic storage system in which a phase-conjugate object beam is reconstructed by the same reference beam that was used for recording. An intermediate hologram is used as a temporary buffer, recorded with its own reference beam and the data-bearing object beam. Reading this buffer hologram with the phase conjugate of its reference beam reconstructs the phase conjugate of the object beam, which can then be recorded into the desired volume hologram for long-term storage. This method combines the immunity to lens aberrations provided by phase-conjugate readout with the simplicity of using the same multiplexed reference beam for both recording and readout. Only a single pair of phase-conjugate reference beams is required. Experimental results are shown with a single LiNbO(3):Fe crystal used as both buffer and storage holograms and a self-pumped phase-conjugate mirror in BaTiO(3) that provides the pair of phase-conjugate reference beams.     

Analysis of the diffracted wave from a volume hologram stored with an irregular pattern

The theoretical analysis for the diffracted wave from a volume hologram stored with an irregular pattern is presented. The relative diffraction efficiencies with respect to position and wavelength of readout wave are calculated by applying the Born approximation for light diffraction. The results are compared with experimental results and the effects of irregular pattern are discussed.     

Improvement of the diffraction efficiency and kinetics of holographic gratings in photochromic media by auxiliary light

Holographic gratings recorded in photochromic media often do not obtain the maximally achievable diffraction efficiency because of diminishing the fringe contrast caused, e.g., by a photochemically active readout beam or unequal intensities of object and reference waves. For nonreversible materials this problem causes a decrease in diffraction efficiency that is proportional to the signal-to-noise ratio (SNR). However, in nonlinear materials such as photochromic media, for which saturation effects need to be considered, an out-of-proportion decrease in the SNR results. It is shown that an overshooting peak during hologram growth, which then decays to a lower permanent level of diffraction, is an indicator for such a situation. Even a weak readout beam may cause such effects, which significantly affect the hologram kinetics. The observed overshooting diffraction efficiency may even be misinterpreted to be dependent on material properties. Experimental and theoretical proof that with low levels of auxiliary light this type of problem can be eliminated completely is presented. Throughout this research bacteriorhodopsin films were used, but the results are valid for photochromic media in general.     

Analysis of lateral-spread photorefractive planar lenses

The photorefractive planar lens for converting a vertical incident plane wave to a lateral-spread spherical wave and vice versa, is suggested. Using the two-beam coupled-wave theory, the coupled wave equations are derived and their half-analytical solutions are also given in terms of an infinite series. The diffraction properties (beam profiles, diffraction efficiency) of the local volume grating in the lens are presented. And the focusing property of the lens is discussed and compared with that of an ideal convergent spherical wave. It is demonstrated that the suggested photorefractive planar lens shows a good focusing effect.     

Volume hologram – Coupled Fabry-Perot etalon

The volume hologram is considered as a series of coupled Fabry-Perot etalon. The interference of multi beam makes the band width of volume hologram very narrow. The positive feedback of Fabry-Perot provides high diffraction efficiency of volume hologram. The computer simulations for volume hologram based on the new model shows a good consistency with the coupled wave theory and the experimental results.     

Design of the spatial filter window for digital holographic convolution reconstruction of object beam field

In the convolution reconstruction process of digital holographic object beam field, the object beam fields with different magnifications can be obtained when the reconstructing beams are spherical waves with different wave curvature radii. This paper presents a theoretical and experimental discussion on the useful spatial frequency spectrum of the hologram numerically illuminated by the spherical wave. The result shows that there would be an image in the spatial frequency spectrum of digital hologram, which is completely the same as the object, if the wave surface radius of the spherical wave is equal to the distance from the object to the CCD sensor. Taking this image as a reference and designing a filter, the position of the reconstructed images with different magnifications can be predicted correctly in the reconstructed plane. Additionally, since the spectrum distribution of zero-order diffraction can be forecasted accurately in theory, its contribution can be effectively eliminated through changing the spatial filter shape; then a reconstructed object field containing more high-frequency information can be obtained.     

The elliptical gaussian wave transformation due to diffraction by an elliptical hologram

Realized as an interferogram of a spherical and a cylindrical wave, the elliptical hologram is treated as a plane diffracting grating which produces Fresnel diffraction of a simple astigmatic gaussian incident wave. It is shown that if the principal axes of the incident beam coincide with the principal axes of the hologram, the diffracted wave field is composed of three different astigmatic gaussian waves, with their waists situated in parallel but distinct planes. The diffraction pattern, observed on a transverse screen, is the result of the interference of the three diffracted wave components. It consists of three systems of overlapped second-order curves, whose shape depends on the distance of the observation screen from the hologram, as well as on the parameters of the incident wave beam and the hologram. The results are specialized for gratings in the form of circular and linear holograms and for the case of a stigmatic gaussian incident wave, as well as for the normal plane-wave incidence on the three mentioned types of hologram.