Anionic polymerization. VI. Effect of polar modifiers on alkylsodium and alkylpotassium polymerization of butadiene

It was found that N,N,N′,N′-tetramethylethylene diamine and hexamethyl phosphorus triamide minimize chain transfer reactions in the polymerization of 1,3-butadiene in hydrocarbon solvent with alkylsodium or alkylpotassium initiators. The polymers obtained with alkylsodium initiators had a high molecular weight and high vinyl content at 90–95% conversion. The molecular weight of the polybutadiene made by alkylsodium and alkylpotassium initiators was dependent on the polymerization temperatures and modifier ratios, but the vinyl contents were independent of the modifier ratios. Vinyl contents of alkylpotassium-initiated polymers showed a slight dependency on polymerization temperature; the vinyl contents of alkylsodium-initiated polymers were independent of temperature. Addition of lithium tert-butoxide and potassium tert-amylate to these initiators in the presence of the modifiers affected the molecular weight but not the microstructure.     

Preparation of water‐soluble,syndiotacticity‐rich,low molecular weight poly(vinyl alcohol) microfibrils in high yields with the low‐temperature polymerization of vinyl pivalate in tetrahydrofuran and saponification

To prepare water‐soluble, syndiotacticity‐rich poly(vinyl alcohol) (PVA) microfibrils for various industrial applications, we synthesized syndiotacticity‐rich, low molecular weight PVA by the solution polymerization of vinyl pivalate (VPi) in tetrahydrofuran (THF) at low temperatures with 2,2′‐azobis(2,4‐dimethylvaleronitrile) (ADMVN) as an initiator and successive saponification of poly(vinyl pivalate) (PVPi). Effects of the initiator and monomer concentrations and the polymerization temperature were investigated in terms of the polymerization behaviors and molecular structures of PVPi and the corresponding syndiotacticity‐rich PVA. The polymerization rate of VPi in THF was proportional to the 0.91 power of the ADMVN concentration, indicating the heterogeneous nature of THF polymerization. The low‐temperature solution polymerization of VPi in THF with ADMVN proved to be successful in obtaining water‐soluble PVA with a number‐average degree of polymerization (P_n) of 300–900, a syndiotactic dyad content of 60–63%, and an ultimate conversion of VPi into PVPi of over 75%. Despite the low molecular weight of PVA with P_n = 800, water‐soluble PVA microfibrillar fibers were prepared because of the high level of syndiotacticity. In contrast, for PVA with P_n = 330, shapeless and globular morphologies were observed, indicating that molecular weight has an important role in the in situ fibrillation of syndiotacticity‐rich PVA. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1103–1111, 2002     

Radical polymerization behavior of ethyl ortho-formylphenyl fumarate involving intramolecular hydrogen abstraction

The radical polymerization behavior of ethyl ortho-formyl-phenyl fumarate (EFPF) using dimethyl 2,2′-azobisisobutyrate (MAIB) as initiator was studied in benzene kinetically and ESR spectroscopically. The polymerization rate (R_p) at 60°C was given by R_p = k[MAIB]^0.76[EFPF]^0.56. The number-average molecular weight of poly(EFPF) was in the range of 1600–2900. EFPF was also easily photopolymerized at room temperature without any photosensitizer probably because of the photosensitivity of the formyl group of monomer. Analysis of ¹H? and ¹³C-NMR spectra of the resulting polymer revealed that the radical polymerization of EFPF proceeds in a complicated manner involving vinyl addition and intramolecular hydrogen-abstraction. The polymerization system was found to involve ESR-observable poly(EFPF) radicals under the actual polymerization conditions. ESR-determined rate constant (2.4–4.0 L/mol s) of propagation at 60°C increased with decreasing monomer concentration, which is mainly responsible for the observed low de-pendency of R_p on the EFPF concentration. Copolymerizations of EFPF with some vinyl monomers were also examined. © 1995 John Wiley & Sons, Inc.     

Radical block polymerization of vinyl chloride. II. Synthesis and characterization of vinyl chloride block copolymers

Peroxidized polypropylene has been used as a heterofunctional initiator for a two-step emulsion polymerization of a vinyl monomer (M₁) and vinyl chloride with the production of vinyl chloride block copolymers. Styrene, methyl-, and n-butyl methacrylate and methyl-, ethyl-, n-butyl-, and 2-ethyl-hexyl acrylate have been used as M₁ and polymerized at 30–40°C. In the second step vinyl chloride was polymerized at 50°C. The range of chemical composition of the block copolymers depends on the rate of the first-step polymerization of M₁ and the duration of the second step; e.g., with 2-ethyl-hexyl acrylate block copolymers could be obtained with a vinyl chloride content of 25–90%. The block copolymers have been submitted to precipitation fractionation and GPC analysis. Noteworthy is the absence of any significant amount of homopolymers, as well as poly(M₁)n as PVC. The absence of homo-PVC was interpreted by an intra- and intermolecular tertiary hydrogen atom transfer from polypropylene residue to growing PVC sequences. The presence of saturated end groups on the PVC chains is responsible for the improved thermal stability of these block polymers, as well as their low rate of dehydrochlorination (180°C). Molecular aggregation in solution has been shown by molecular weight determination in benzene and tetrahydrofuran.     

Cycloaddition approach to the curing of polyimides via precursor containing thiophene‐S,S‐dioxide

A new method for linear polymerization of maleimides via the Diels–Alder reaction has been developed. This method involves use of a new cross‐linking agent, benzene‐3,4‐dimethylenesuccinimide, which can be generated in situ from its thiophene precursor, benzene‐2,5‐dihydrothiophene‐3,4‐dicarboximide‐S,S‐dioxide. This new cross‐linking agent is reasonably reactive, readily prepared, and stable at room temperature. A controlled molecular weight oligomer has been synthesized and applied to the polymerization to yield a highly thermal stable polyimide. © 2006 Wiley Periodicals, Inc. Heteroatom Chem 17:648–652, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/hc.20249     

Living cationic polymerization of α‐methyl vinyl ethers using SnCl4

Cationic polymerization of α‐methyl vinyl ethers was examined using an IBEA‐Et_1.5AlCl_1.5/SnCl₄ initiating system in toluene in the presence of ethyl acetate at 0 ～ ?78 °C. 2‐Ethylhexyl 2‐propenyl ether (EHPE) had a higher reactivity, compared to corresponding vinyl ethers. But the resulting polymers had low molecular weights at 0 or ?50 °C. In contrast, the polymerization of EHPE at ?78 °C almost quantitatively proceeded, and the number‐average molecular weight (M_n) of the obtained polymers increased in direct proportion to the EHPE conversion with quite narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ≤ 1.05). In monomer‐addition experiments, the M_n of the polymers shifted higher with low polydispersity as the polymerization proceeded, indicative of living polymerization. In the polymerization of methyl 2‐propenyl ether (MPE), the living‐like propagation also occurred under the reaction conditions similar to those for EHPE, but the elimination of the pendant methoxy groups was observed. The introduction of a more stable terminal group, quenched with sodium diethyl malonate, suppressed this decomposition, and the living polymerization proceeded. The glass transition temperature of the obtained poly(MPE) was 34 °C, which is much higher than that of the corresponding poly(vinyl ether). This poly(MPE) had solubility characteristics that differed from those of poly(vinyl ethers). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2202–2211, 2008     

Organometallic polymers. XXV. Preparation of polyvinylferrocene

The synthetic details of solution polymerization in benzene and bulk polymerization of vinylferrocene are reported. In benzene solutions, with azobisisobutyronitrile (AIBN) as the initiator, small yields of low-polydispersity low molecular weight (M?_n ? 5000) polyvinylferrocene is obtained. However, high yields can be obtained by continuous or multiple AIBN addition. Higher molecular weight polymers and binodal polymers can be obtained as the monomer concentration is increased. In bulk polymerizations, yields of 80% can be obtained. The molecular weight increases as temperature decreases from 80 to 60°C in bulk polymerizations, and an increasing amount of insoluble polymer results. The soluble portion is often binodal, the higher molecular weight node consisting of an increasingly branched structure. Lower molecular weight polymer was readily fractionated into narrow fractions from benzene–methanol systems, but higher molecular weight polymer proved impossible to fractionate into narrow fractions due to branching.     

Kinetics of free-radical polymerization of p-vinylbenzyl methyl ether: Crosslinking by initiator free radicals

Kinetics of polymerization of p-vinylbenzyl methyl ether at low conversion either in bulk or in benzene have been found to be quite similar to those of the unsubstituted monomer styrene. Rates of polymerization initiated by peroxides or α,α′-azobisisobutyronitrile over the temperature range 50–70°C. have been found to be proportional to [Monomer][Initiator]^1/2 with an activation energy difference E_propagation – 1/2 E_termination ≈ 6 kcal./mole. Azo initiation leads to essentially unbranched poly(vinyl-benzyl methyl ether) even at very high conversions, whereas initiation of undiluted monomer by diacyl peroxides results in some crosslinking at high conversion. Use of biacetyl as a photoinitiator of polymerization over the temperature range 0–60°C. with either bulk monomer or monomer solutions in benzene has been found in each instance to yield crosslinked, insoluble polymers at low degrees of conversion. Benzene solutions of soluble polymer have been converted to high molecular weight branched polymers by free radicals generated by photolysis of biacetyl, and a substantial preference of methyl free radicals to abstract benzyl hydrogens of poly(p-vinylbenzyl methyl ether) rather than add to solvent benzene has been observed.     

A possible mechanism for benzene formation during the pyrolysis of poly(vinyl chloride)

We studied the evolution of hydrogen chloride and benzene from two PVC samples differing only in molecular weight, during a slow pyrolysis experiment. It appears that the evolution rates and total amount of benzene decrease rapidly when molecular weight increases. Twenty to 30 benzene molecules are formed per initial chain-end. The proposed radical mechanism involves a cyclohexadienyl radical as intermediate and initiation from terminal 1-chloro-vinyl units.     

Investigation of catalyst‐transfer condensation polymerization for synthesis of poly(p‐phenylenevinylene)

Kumada‐Tamao coupling polymerization of 1,4‐dialkoxy‐2‐bromo‐5‐(2‐chloromagnesiovinyl)benzene ( 1 ) and 1,4‐dialkoxy‐2‐(2‐bromovinyl)‐5‐chloromagnesiobenzene ( 2 ) with a Ni catalyst and Suzuki‐Miyaura coupling polymerization of 2‐{2‐[(2,5‐dialkoxy‐4‐iodophenyl)]vinyl}‐4,4,5,5‐tetramethyl‐1,3,2‐dioxaborolane ( 3 ), its bromo counterpart 4 , and 2,5‐dialkoxy‐4‐(2‐bromovinyl)phenylboronic acid ( 5 ) with a Pd initiator were investigated under catalyst‐transfer condensation polymerization conditions for the synthesis of well‐defined poly(p‐phenylenevinylene) (PPV). The Kumada‐Tamao polymerization of vinyl Grignard‐type monomer 1 with Ni(dppp)Cl₂ at room temperature did not proceed, whereas aryl Grignard‐type monomer 2 afforded oligomers of low molecular weight. Matrix‐assisted laser desorption ionization time‐of‐flight (MALDI‐TOF) mass spectra of the polymer obtained from 2 implied that the Grignard end group reacted with tetrahydrofuran to terminate polymerization. On the other hand, Suzuki‐Miyaura polymerization of vinyl boronic acid ester type monomers 3 and 4 and phenylboronic acid type monomer 5 with a Pd initiator and aqueous KOH at ?20 °C to room temperature yielded the corresponding PPV with high molecular weight within a few minutes. However, the molecular weight distribution was broad, and MALDI‐TOF mass spectra showed the peaks of polymers bearing no initiator unit at the chain end, as well as those of polymers with the initiator unit. These results indicated that intermolecular chain transfer of the Pd catalyst occurred. Dehalogenation and disproportionation of the growing end also took place as side reactions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2643‐2653     

The mechanism of the reversible reaction: 2C2H2 ⇌ vinyl acetylene and the pyrolysis of butadiene

It is shown that kinetic data on the polymerization of acetylene to vinyl acetylene and benzene can be reconciled with the formation of a 1,4 biradical which can isomerize by a 1-3, H-atom shift to the molecular product. Since the biradicals have a negligibly small life-time in the system the overall process appears to be a concerted bimolecular reaction. The labile isomer CH₂ ? C: which had been suggested as being the reactive intermediate, is argued on energy considerations not to be a plausible intermediate. Data on the reverse pyrolysis of vinyl acetylene to acetylene are consistent with the model. Extending the model to butadiene explains the observed molecular nature of its decomposition to ethylene and acetylene. Reactions of other oligomers of acetylene are discussed.     

Fire- and heat-resistant adhesive resins based on maleimido and citraconimido substituted 1-[(dialkoxyphosphinyl)methyl]-2,4- and -2,6-diaminobenzenes

A novel class of fire- and heat-resistant bisimide resins was prepared by thermal polymerization of maleimido or citraconimido derivatives of 1-[(dialkoxyphosphinyl)methyl]-2,4- and -2,6-diaminobenzenes (1). The neat bisimide resin prepared by curing 1-[di(2-chloroethoxyphosphinyl)methyl]-2,4- and -2,6-bismaleimidobenzene exhibited a limiting oxygen index 75% higher and smoke evolution about 30 times lower compared with the parent polymer obtained by curing m-phenylenebismaleimide. The char yield of cured bisimide resins at 700°C was 58–70% in a nitrogen atmosphere and 35–60% in air. An increase in formula weight between the imide groups slightly reduced the char yield. The polymer precursors were synthesized by reacting the phosphorus-containing diamines (1) (1 mol) with maleic anhydride/citraconic anhydride (2 mol) or by reacting the monomaleimido derivative of (1) with benzophenone tetracarboxylic dianhydride/methylenebis(4-phenylisocyanate) in a 2:1 mole ratio. The monomers were characterized by elemental analysis, Fourier-transform–infrared (FT-IR), proton nuclear magnetic resonance (¹H-NMR) spectroscopy, and gas chromatography–mass spectroscopy (GC-MS). Direct cleavage of the P? C bond and inversion of the synthesis reaction may occur during their pyrolysis. The thermal polymerization of the monomers was investigated by differential scanning calorimetry (DSC). Biscitraconimides are thermally polymerized at a relatively lower temperature than the corresponding bismaleimides.     

Phase‐equilibrium behavior of vinyl chloride/n‐butane and its application in determination of vinyl chloride heterogeneous polymerization kinetics

Studies of the phase‐equilibrium behavior of vinyl chloride (VCM)/n‐butane mixtures and the kinetics of VCM heterogeneous polymerization, using n‐butane as a reaction medium, were carried out using a 1‐L glass autoclave. The vapor composition was measured by gas chromatography, showing that the vapor pressure of the VCM/n‐butane mixture was located above the line connecting the points for pure VCM and n‐butane. The concentration of VCM in the vapor phase was greater than that in the corresponding liquid phase. It was confirmed that the presence of poly(vinyl chloride) (PVC) resin had no significant influences on the phase equilibrium of VCM/n‐butane mixtures. Thus, the phase‐equilibrium equations were applied to determine the conversion of VCM during heterogeneous polymerization. The conversions calculated from the variations of vapor pressure or composition agreed with those determined by the weighing method. The conversion–time and polymerization rate–time curves obtained for VCM heterogeneous polymerization showed that the polymerization accelerated at low initiator concentration, but the polymerization rate decreased with an increase of conversion at relatively high initiator concentrations. The chain‐transfer reaction to n‐butane was confirmed by a decrease of the molecular weight and broadening of the molecular weight distribution of PVC. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2179–2188, 2001     

Laccase-catalyzed polymerization of acrylamide

Enzymatic polymerization of acrylamide was carried out in water. Laccase, a copper-containing oxidoreductase derived from Pycnoporus coccineus, induced the polymerization at relatively low temperature (50°C) to give a polymer of high molecular weight. In the presence of 2,4-pentanedione, laccase efficiently mediated the vinyl polymerization at room temperature.     

Cationic cyclopolymerization of new divinyl ethers: The effect of ether and ester neighboring functional groups on their cyclopolymerization tendency

The cationic polymerization of two new divinyl ethers, 1‐(2‐vinyloxyethoxy)‐2‐[(2‐vinyloxyethoxy)carbonyl]benzene ( 2 ) and 1,2‐bis[(2‐vinyloxyethoxy)carbonyl]benzene ( 3 ), as well as 1,2‐bis(2‐vinyloxyethoxy)benzene ( 1 ), with BF₃OEt₂ in CH₂Cl₂ at 0 °C at low initial monomer concentrations ([M]₀ = 0.15 and 0.075 M) gave soluble polymers with relatively high molecular weights and broad molecular weight distributions (MWDs), whereas reactions with the HCl/ZnCl₂ initiating system yielded soluble polymers with relatively narrow MWDs (weight‐average molecular weight/number‐average molecular weight ? 1.6) under similar reaction conditions. An NMR structural analysis of the HCl/ZnCl₂‐mediated polymers from the divinyl ethers showed that poly( 1 ) had virtually no unreacted vinyl ether groups throughout the polymerization (monomer conversion = 28–98%), whereas poly( 2 ) and poly( 3 ) possessed some amount of unreacted vinyl ether groups in the initial stage of the polymerization; the content of the vinyl groups of poly( 2 ) was 18 mol % at a 15% monomer conversion, and the content of the vinyl groups of poly( 3 ) was 31 mol % at an 18% monomer conversion. Therefore, divinyl ether 1 underwent cyclopolymerization exclusively to give almost completely cyclized polymers [degree of cyclization (DC) ～ 100%], whereas divinyl ethers 2 and 3 exhibited a lower cyclopolymerization tendency [DC for poly( 2 ) = 82%; DC for poly( 3 ) = 69%]. The differences in the cyclopolymerization tendencies among the divinyl ethers can be explained by the differences in the solvation powers of the neighboring functional groups adjacent to the vinyl ether moiety with the active center: the ether oxygen of the ether neighboring group solvates intramolecularly with the active center to accelerate the intramolecular propagation, but such an interaction is less effective with the more electron‐deficient oxygen attached to the carbonyl group of the ester neighboring group. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 281–292, 2003     

Free-radical copolymerizations of 1,2-dichloroethylenes. Evidence for chain transfer by chlorine atom elimination

Trialkylboron–oxygen, an active, low-temperature free-radical initiator, has been employed to investigate the effects of very low temperatures on the copolymerizations of vinyl acetate with cis and trans-1,2-dichloroethylenes. The low temperatures favor the propagation rate relative to the transfer rate, such that high molecular weight copolymers containing substantial quantities of 1,2-dichloroethylene can be prepared. The molecular weights of the copolymers depend only on the amounts of 1,2-dichloroethylene in the copolymers, regardless of the isomer which takes part in the copolymerization. Since the double bond of the trans isomer is about six times as reactive as that of the cis isomer, this indicates that the dominating chain transfer reaction occurs by chlorine atom elimination subsequent to the addition of the dichloroethylene unit to the growing free radical chain. It is suggested that a similar chain-transfer mechanism occurs in the polymerization of vinyl chloride, wherein an infrequent head-to-head placement of monomer unit is followed by ejection of a chlorine atom to form an olefinic bond and termination of that growing chain. The presence of the 1,2-dichloroethylene unit in the copolymer increases the glass transition temperature approximately 1°C per weight per cent copolymerized with the vinyl acetate.     

Effect of acetylene on the γ-radiation-induced polymerization of ethylene

The effects of acetylene on the γ-radiation-induced polymerization of ethylene were studied from the viewpoint of the gaseous products and polymer structure. The experiments were carried out under a pressure of 400 kg/cm²; the temperature was 30°C; the does rate was 1.1 × 10⁵ rad/hr; and the acetylene content was 0–20%. The solid polymer was obtained in the polymerization of ethylene containing 2.2% acetylene, while the monomer containing 19.7% acetylene gave a yellowish viscous oil. The polymer yield and molecular weight decreased remarkably with acetylene content. The main gaseous product was hydrogen, and trace amounts of butane, butene-1, butadiene-1,3, and benzene and its derivatives were also observed. The rate of formation of hydrogen was almost independent of acetylene content and there was no difference in acetylene contents before and after the irradiation was found. The infrared spectra of the polymers showed the presence of vinylidene, trans-vinylene, and terminal vinyl unsaturations, 1,4-disubstituted benzene, and carbonyl groups. The contents of trans-vinylene, terminal vinyl, and methyl groups increased with acetylene content, and that of vinylidene was independent of acetylene content. The monomer reactivity ratios of ethylene and acetylene were evaluated as 45.5 and 66.0, respectively. On the basis of the results, the effects of acetylene on the γ-radiation-induced polymerization of ethylene were discussed.     

Kinetics of self‐condensing vinyl hyperbranched polymerization in three‐dimensional space

Self‐condensing vinyl hyperbranched polymerization (SCVP) with A‐B* type monomer is simulated applying Monte Carlo method using 3d bond fluctuation lattice model in three‐dimensional space. The kinetics of SCVP with zero active energy of reaction is studied in detail. It is found that the maximal number–average and weight–average polymerization degrees and the maximal molecular weight distribution, at varying the initial monomer concentration and double bond conversion, are about 52, 190, and 3.93, respectively, which are much lower than theoretical values. The maximal average fraction of branching points is about 0.27, obtained at full conversion at the initial monomer concentration of 0.75. The simulation demonstrated the importance of steric effects and intramolecular cyclization in self‐condensing vinyl hyperbranched polymerization. The results are also compared with experiments qualitatively and a good agreement is achieved. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4486–4494, 2008     

污泥热解过程中焦的表面孔隙结构分形生长

主要对污水污泥在高温热解和低温热解条件下热解焦炭的表面孔隙结构特性进行了研究。结果表明,污泥热解过程中随着挥发分的析出,污泥热解焦炭的孔隙结构逐渐发达。低温和高温热解过程中挥发分的析出,使得孔径为3.75 nm的孔得到了极大的发展。通过对污泥热解焦炭的N2吸附过程进行的分形分析发现,不同停留时间低温和高温热解焦炭的表面分形维数可以分为FD-1和FD-2。其中,FD-1主要表征了较大孔(0.86 nm)的表面分形维数,FD-2则主要表征了超微孔(0.86 nm)的表面分形维数。随着热解停留时间的延长,FD-1和FD-2逐渐增大并趋于稳定。与高温热解焦炭的超微孔表面分形维数相比低温热解焦炭出现了较大的增加,而较大孔的表面分形维数则相对低温热解焦炭未见有较大的改变。     

Synthesis of poly(vinyl acetate)‐graft‐polystyrene by a combination of cobalt‐mediated radical polymerization and atom transfer radical polymerization

Vinyl acetate and vinyl chloroacetate were copolymerized in the presence of a bis(trifluoro‐2,4‐pentanedionato)cobalt(II) complex and 2,2′‐azobis(4‐methoxy‐2,4‐dimethylvaleronitrile) at 30 °C, forming a cobalt‐capped poly(vinyl acetate‐co‐vinyl chloroacetate). The addition of 2,2,6,6‐tetramethyl‐1‐piperidinyloxy after a certain degree of copolymerization was reached afforded 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐terminated poly(vinyl acetate‐co‐vinyl chloroacetate) (PVOAc–MI; number‐average molecular weight = 31,000, weight‐average molecular weight/number‐average molecular weight = 1.24). A ¹H NMR study of the resulting PVOAc–MI revealed quantitative terminal 2,2,6,6‐tetramethyl‐1‐piperidinyloxy functionality and the presence of 5.5 mol % vinyl chloroacetate in the copolymer. The atom transfer radical polymerization (ATRP) of styrene (St) was studied with ethyl chloroacetate as a model initiator and five different Cu‐based catalysts. Catalysts with bis(2‐pyridylmethyl)octadecylamine (BPMODA) or tris(2‐pyridylmethyl)amine (TPMA) ligands provided the highest initiation efficiency and best control over the polymerization of St. The grafting‐from ATRP of St from PVOAc–MI catalyzed by copper complexes with BPMODA or TPMA ligands provided poly(vinyl acetate)‐graft‐polystyrene copolymers with relatively high polydispersity (>1.5) because of intermolecular coupling between growing polystyrene (PSt) grafts. After the hydrolysis of the graft copolymers, the cleaved PSt side chains had a monomodal molecular weight distribution with some tailing toward the lower number‐average molecular weight region because of termination. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 447–459, 2007