二氧化碳在铜氧化膜电极上的光电化学还原

本文研究了CO_2在铜阳极氧化膜电极上的光电化学还原行为,在还原电量小于0.1C时,CH_4 的产率较高;还原电量大于2.0C时,主要还原产物为CH_3OH,还对CH_4的产率随外加电位、还原电量和铜阳极氧化膜制备条件的变化关系进行了研究,并对其还原机理作了初步探讨。     

电化学方法分析铅阳极膜的相组成

本文提出使用线性电位扫描和电位衰退定性和定量分析铅在4.5mol·dm^-^3H2SO4(30℃)中形成的阳极膜的相组成并与现场X射线衍射, 原子吸收光谱, 阳极溶出等法比较。结果表明电位扫描伏安曲线的峰电位和电位扫描至峰电位左右时电极开路后, 所得的稳定电位可用于阳极膜相组成的定性分析, 电位扫描伏安电线电流峰的面积可用于阴极膜相组成的定量分析。本文的阳极膜由PbO·PbSO4, PbO2和PbOn(2>n>1)组成, 以PbO·PbSO4为主要成份。     

季阳离子基团对聚吡咯膜伏安特性的影响

在含有相同阴离子与不同阳离子基团的电解质溶液中用电位阶跃技术制备了聚吡咯(PPy)膜，用循环伏安法于空白溶液中研究了膜的电化学行为。研究结果表明随着阳离子基团增大，制膜时消耗的电量减小，膜的氧化还原电流下降，阴极和阳极峰电位分别向更负和更正的方向移动。扫描电镜显示阳离子基团对PPy膜的沉积过程和形态结构产生了一定的影响。     

Pt电极表面有机小分子毒化中间体CO覆盖度的有效调控

燃料电池因高能量利用率和环境友好等优点成为最有发展前途的一种能量利用方式,但有机小分子中间产物(CO)导致催化剂中毒一直是困扰燃料电池阳极催化剂的重要问题.本文利用可控电位高效更换溶液的电解池研究了不同电位下甲醛(HCHO)在Pt电极上解离CO的过程.实验结果表明,随着电位正移,HCHO在Pt上产生的CO覆盖度由.0.2 V的71%逐渐下降到0.25 V的60%.0.3 V起覆盖度急剧下降,在0.35 V时控电位的覆盖度仅有8%,远小于开路电位(ocp)下的64%.这预示着可以利用CO覆盖度的区别,提出一种新的电极操作方法以降低CO对电极的毒化.HCHO验证实验表明,控电位0.35 V时加入甲醛稳定300 s后,起始氧化电流为3×10~(-4 )A,接近峰值电流4×10~(-4) A,远大于ocp实验的3×10~(-5) A.控制工作电极电位0.35 V时加入甲醛,有效地降低了CO毒化对电极的影响     

复杂阴极保护体系三维有限元建模研究

滨海电厂常以天然海水作冷却水,其碳钢水室和钛管凝汽器在实施阴极保护过程中,要求钢电位应低于-0.85V(vs.SCE),电位过正则碳钢保护不足,而钛的电位则须高于-0.75V(vs.SCE),电位过负则易使钛管发生氢脆损伤.研究牺牲阳极阴极保护,需先得出两种金属在阴极保护过程中的电位分布.本文在设计室建立碳钢水室钛管模型,根据该实验体系阴极保护过程的(稳态极化和恒电流极化)测定获得两种金属有效的边界条件,用有限元(FEM)计算在一个牺牲阳极阴极保护状态得到三维电位分布.计算结果和测量结果基本一致,为优化阴极保护设计提供了理论依据.     

碳素钢钝化的线性电位扫描法问题

电位扫描法是一种基本的电化学研究方法。前人对此作了大量的研究。对于具有表面转化步骤的复杂电极过程,尤其是阳极过程,Srinivasan等作了扫描电位—电流的理论分析,导出了峰值电流(I_(max)或i_p)与扫描速度的平方根(v~(1/2))成正比的近似数学关系式,可较好地应用于有机物电化学吸附,以及H_2、O_2在某些金属表面的电化学吸附。金属钝化过程是金属阳极溶出过程中含氧金属粒子在金属表面生成化学吸附层并且继续发展形成表面     

辛可宁修饰碳糊电极的应用研究——铋的阳极溶出伏安法测定

报道了利用辛可宁修饰碳糊电极测定铋的方法,在1mol/LH2SO4溶液中,通过在－1.00V电位下富集Bi3＋后,在－0.20～＋0.15V电位范围内作阳极溶出伏安法测定。在－0.022V处有一灵敏的氧化峰,峰电流与Bi     

流动注射双安培法测定没食子酸

基于没食子酸在经预阳极化的铂电极上的催化氧化和不可逆电对的双安培检测原理,使用经过恒电位预阳极化处理的双铂电极,在外加电位差为0V时,通过偶合没食子酸在一支电极上的氧化和氧化铂在另一支电极上的还原两个不可逆电极过程,构建流动注射双安培检测体系,建立了一种流动注射双安培直接检测没食子酸的新方法。常用药物赋形剂、无机离子以及生化样品中一些共存物均不干扰没食子酸测定。没食子酸的氧化电流与其浓度在1.0×10-5～1.0×10-3mol/L范围内有良好的线性关系。检出限为5.0×10-6mol/L。连续20次测定2.0×10-4mol/L没食子酸,电流值的RSD为1.7%。该方法有很高的选择性和灵敏度,样品处理方法简单快速,适于在线分析。     

流动注射双安培法测定葛根素

利用不可逆电对的双安培检测原理,建立了流动注射双安培直接检测葛根素的电化学新方法.使用经过恒电位预阳极化处理的双铂电极,通过耦合葛根素在一支电极上的氧化和氧化铂在另一支电极上的还原两个不可逆电极过程,构成流动注射双安培检测体系.在外加电位差为0.2 V时,pH 8.94的碳酸钠-碳酸氢钠缓冲溶液中,测得氧化电流与葛根素浓度在6.0×10-6～1.0×10-3 mol/L范围内呈线性关系(r=0.997 4,n=8),检出限为1.0×10-6 mol/L.连续40次测定6.0 ×10-4 mol/L的葛根素,RSD=1.58%.用该方法对葛根素含量进行了测定,结果令人满意.     

CO2-3对羟基乙叉二膦酸镀铜液的影响

研究羟基乙叉二膦酸(HEDPA)镀铜液中CO2-3含量对电沉积时阴、阳极过程及镀层的择优取向的影响. 通过分析阴、阳极的动电位极化曲线, 发现镀液中逐渐加入的CO2-3提高了阴极的极化, 使电结晶晶粒细化, 直至达到稳定; 同时促进了铜阳极的溶解. 而X射线衍射(XRD)结果表明, 铜镀层的晶面择优取向从(222)逐渐向(111)转变. 通过镀液中固体络合物的红外光谱分析表明, CO2-3的加入以第二配体的方式进入该镀液的放电络合离子结构中, 参与Cu2+的络合, 形成更稳定的络合物, 从而导致铜沉积电位负移, 镀层(111)晶面取向增强.     

Electrocatalytic activity of a novel titanium-supported nanoporous gold catalyst for glucose oxidation

A novel Ti-supported gold catalyst (nanoAu/Ti) with a nanoporous 3D texture has been fabricated using a hydrothermal method. Au particles were stably deposited on the Ti surface from the mixture of aqueous tetrachlororoauric acid and polyethylene glycol at 180 °C. Voltammetry (CV) and chronoamperometry were used to characterize the nanoAu/Ti electrode and assess its electroactivity towards glucose oxidation. Compared to polycrystalline Au, the nanoAu/Ti electrode shows similar CV profiles in alkaline solution. However, in an alkaline solution containing 10 mM glucose, the nanoAu/Ti electrode presents much higher anodic current densities and a more negative onset potential (ca. ?0.75 V) for glucose oxidation than a bulk Au electrode. Analysis for Tafel plot of the nanoAu/Ti electrode shows that electro-oxidation of glucose takes place via a one-electron rate-determining step. Results indicate a high and (relatively) stable electrocatalytic activity of the nanoAu/Ti for glucose oxidation.     

On-line removal of redox-active interferents by a porous electrode before amperometric blood glucose determination

A porous reticulated vitreous carbon (RVC) electrode and a disk electrode coupled in tandem in an electrochemical flow cell has been used for electrolytic removal of interferents before amperometric glucose detection. The electrolytic efficiency at the upstream RVC electrode is 100% at a flow rate of 0.1 mL min⁻¹ or lower. Potential interferents such as acetaminophen, ascorbic acid, and uric acid can be completely eliminated by electrolysis at the RVC electrode. A mixed monolayer comprising glucose oxidase (GOD) and ferrocenyl-1-undecanethiol preformed at the downstream gold disk electrode was used as a mediator-based amperometric glucose sensor. The dependence of the amperometric current on the glucose concentration exhibits good linearity across over three orders of magnitude. The glucose measurements were also found to be reproducible (RSD < 3.5%) and accurate. Unlike the chemiluminescence method, this device obviates the use of carcinogenic substrates and the glucose sensor performance is independent of the oxygen present in sample. On the basis that the RVC electrode requires minimal cleanup and the GOD-modified electrode remains stable for a week, the electrochemical flow cell should be amenable for automated on-line removal of redox interferents for other types of enzyme-based biosensors.     

纳米级微带金电极上葡萄糖氧化酶的固定.性质及应用

实现了葡萄糖氧化酶以及葡萄糖氧化酶和电子传递媒体Fe(CN)^3^-~6同时在纳米级微带电极上的固定,用红外光谱和循环伏安对GOD/PPy微电极进行了表征, 研究了微带金电极上聚吡咯恒电位形成过程的动力学及葡萄糖氧化酶对其动力学过程的影响,探讨了微酶电极GOD/Fe(CN)^3^-~6/PPy对葡萄糖氧化的催化作用, 考察了PPy膜厚度和溶液中氧的存在对GOD/Fe(CN)^3^-~6/PPy微电极测定葡萄糖的影响.     

电沉积二氧化锰成核机理及其充放电性能

采用计时电流法沉积纳米MnO₂电极材料,利用Scharifker-Hills成核理论模型分析时间-电流(i-t)曲线判断了MnO₂成核机理。 对3种不同的成核方式制得的MnO₂材料进行电化学超级电容性能测试、用SEM观察了其微观形貌。 比较了不同沉积方法对沉积材料结构、电容性能的影响。 计时电流测试发现,在0.1 mol/L Mn²⁺溶液中,电势阶跃至0.365 V,初始成核符合瞬时成核机理,在0.01 mol/L Mn²⁺溶液中,电势阶跃至0.418 V,初始成核存在瞬时成核和连续成核两种不同机理,在0.5 mmol/L Mn²⁺溶液中,电势阶跃至0.515 V,初始成核则符合连续成核机理。 超级电容性能测试发现,瞬时成核下制得的MnO₂电极材料相对于另外两种成核方式得到的电极材料具有更好的电容性能,这是因为瞬时成核更易于形成多孔、纳米片(棒)状等高比表面积的沉积物,表明制备方法影响MnO₂电极材料电容性能。     

Comparative studies on electrogenerated chemiluminescence of luminol on gold nanoparticle modified electrodes

Comparative studies on the electrogenerated chemiluminescence (ECL) behavior of luminol on various electrodes modified with gold nanoparticles of different size were carried out in neutral solution by conventional cyclic voltammetry (CV). The results demonstrated that the gold nanoparticle modified electrodes could generate strong luminol ECL in neutral pH conditions. The catalytic performance of gold nanoparticle modified electrodes on luminol ECL depended not only on the gold nanoparticles but also on the substrate. Gold electrode and glassy carbon electrode were the most suitable substrates for the self-assembly of gold nanoparticles. Moreover, the gold nanoparticle modified gold and glassy carbon electrode had satisfying stability and reproducibility and did not need tedious pretreatment of electrode surface before each measurement. It was also found that luminol ECL behavior depended on the size of gold nanoparticles. The most intense ECL signals were obtained on a 16-nm-diameter gold nanoparticle modified electrode. The modified electrode prepared by the self-assembly method exhibited much better catalytic effect on luminol ECL than that prepared by the electrically deposited method. The ECL behavior of luminol on a gold nanoparticle self-assembled gold electrode was also investigated by other transient-state electrochemical techniques, such as chronoamperometry, differential pulse voltammetry, normal pulse voltammetry, and square wave voltammetry. The strongest ECL intensity was obtained under square wave voltammetric condition.     

Electrocatalytic Oxidation of Hydrogen Peroxide on Poly(m‐toluidine)‐Nickel Modified Carbon Paste Electrode in Alkaline Medium

The poly(m‐toluidine) film was prepared by using the repeated potential cycling technique in an acidic solution at the surface of carbon paste electrode. Then transition metal ions of Ni(II) were incorporated to the polymer by immersion of the modified electrode in a 0.2 M NiSO₄, also the electrochemical characterization of this modified electrode exhibits stable redox behavior of the Ni(III)/Ni(II) couple. The electrocatalytic ability of Ni(II)/poly(m‐toluidine)/modified carbon paste electrode (Ni/PMT/MCPE) was demonstrated by electrocatalytic oxidation of hydrogen peroxide with cyclic voltammetry and chronoamperometry methods in the alkaline solution. The effects of scan rate and hydrogen peroxide concentration on the anodic peak height of hydrogen peroxide oxidation were also investigated. The catalytic oxidation peak current showed two linear ranges with different slopes dependent on the hydrogen peroxide concentration and the lower detection limit was 6.5 μM (S/N=3). The catalytic reaction rate constant, (k_h), was calculated 5.5×10² M^?1 s^?1 by the data of chronoamperometry. This modified electrode has many advantages such as simple preparation procedure, good reproducibility and high catalytic activity toward the hydrogen peroxide oxidation. This method was also applied as a simple method for routine control and can be employed directly without any pretreatment or separation for analysis cosmetics products.     

纳米级金膜微电极的制作,表征及异相催化反应

报道了纳米级金膜微电极的制作方法，用ＸＰＳ及ＳＥＭ对电极表面进行了表征，考察了该电极的循环伏安及计时电流特性，在聚吡咯修饰微带金电极上成功地实现了葡萄糖氧化酶和电子传递媒体Ｆｅ（ＣＮ）６＾３－的同时固定，并研究了ＧＯＤ／Ｆｅ（ＣＮ）６＾３－／ＰＰｙ微酶电极对葡萄糖的响应，稳态响应电流与葡萄糖浓度之间存在Ｍｉｃｈｅａｌｉｓ－Ｍｅｎｔｅｎ动力学特征。     

微环电极上双电位阶跃计时电流和计时库仑法可逆波理论及其验证

推导了微环电极上双电位阶跃计时电流和计时库仑法可逆波理论方程式，并得到了解析表达式。对其电流电量曲线的特性进行了讨论。在亚铁氰化钾－氯化钾体系中，用金微环电极在自制的微机多功能电化学仪器上进行了实验验证，实验结果与理论相符。     

Electrocrystallization of rhodium clusters on thiolate-covered polycrystalline gold

This study reports on the electrochemical deposition of rhodium metal clusters on a polycrystalline gold electrode, modified with a monolayer of dodecanethiol through self-assembly from solution. The deposition process was investigated using cyclic voltammetry, chronoamperometry, and electrochemical quartz crystal microbalance. It is shown that the presence of the thiol monolayer drastically alters the nucleation and growth mechanism compared with the mechanism on the bare gold electrode. The small uncovered gold domains, located at the imperfections in the thiolate monolayer which are induced by the gold nanoroughness, act as nucleation sites for small rhodium clusters. At longer times, these clusters can outgrow the organic monolayer. The resulting surface morphology was characterized by scanning electron microscopy. Rhodium electrocrystallization on the bare gold substrate resulted in an ensemble of a very large amount of very small clusters that are difficult to distinguish from the gold roughness. In contrast, in the presence of a self-assembled monolayer (SAM) of dodecanethiol covalently attached to the gold electrode, the resulting deposit consisted of an ensemble of hemispherical particles. The size distribution of the rhodium particles obtained by using double step chronoamperometry was compared to the ones obtained with cyclic voltammetry and "classical" chronoamperometry. It is shown by X-ray photoelectron spectroscopy that the SAM is still present after rhodium deposition on the thiolate-covered gold substrate. Because the rhodium clusters are directly attached to the gold substrate and can thus easily be electrified, the resulting interface could be used as a composite electrode consisting of a random array of gold supported rhodium nano/microparticles separated from each other by an organic phase. On the other hand, it is shown that the SAM is easily removed by electrochemical oxidation without dissolving the rhodium clusters and, thus, leaving a different array of rhodium clusters on the gold surface compared with the topography obtained in the absence of the SAM. From this point of view, substrate modification with such "removable" organic monolayers was found to be an interesting tool to tune the nano- or microtopography of electrochemically deposited rhodium.     

Simultaneous determination of both the calibration constant in an electrochemical quartz crystal microbalance and the active surface area of a polycrystalline gold electrode

A novel method is employed for the simultaneous determination of both the calibration constant of an electrochemical quartz crystal microbalance (EQCM) and the active surface area of a polycrystalline gold electrode. A gold electrode is immersed into a 1 mM KI/1 M H₂SO₄ solution and on which forms a neutral monolayer. The adsorbed iodine can then be completely oxidized into IO₃⁻. The active surface area of a gold electrode can be obtained from the net electrolytic charge of the oxidation process, and the calibration constant in the EQCM can be calculated from the corresponding frequency shift. The result shows that this method is simple, convenient and valid.