Microbiosensor for Salicylate Based on Modified Carbon Fibre

ABSTRACT

A microbiosensor is proposed for a quick and easy amperometric determination of salicylate. The methodology involves the use of the enzyme salicylate hydroxylase (SH) to convert salicylate to catechol, which is then oxidised at the carbon fibre electrode. The covalent immobilisation of the enzyme onto a carbon fibre electrode via carbodiimide results in an amperometric biosensor with high sensitivity, low detection limit and good stability. The response of the biosensor is linearly proportional to the salicylate concentration between 1.0 10^?7 and 2.0 10^?6 mol L^?1, at an applied potential of 300 mV vs SCE, with a response time of 3.5 s and a detection limit of 3.3 10^?8 mol L^?1. The relative standard deviation for the determination was 4.1% for n=10. The biosensor was applied to determine salicylate in urine and pharmaceutical samples and compared to the reference method with a good correlation.     

Determination of salicylate in beverages and cosmetics by use of an amperometric biosensor

A fast and selective enzymatic method for the determination of salicylate in beverages and cosmetics has been developed. The enzyme salicylate hydroxylase was immobilised covalently onto a glassy carbon working electrode of a wall-jet cell coupled with a flow-injection analysis system. The salicylate is enzymatically converted to catechol, which can be detected amperometrically on the glassy carbon electrode at +0.45 V. The response of the biosensor is linearly proportional to the concentration of salicylate between 725 nmol/l and 700 mol/l. A high sample throughput (60 h^-1) is possible, and the biosensor is stable for more than three months. Sample pretreatment for beverages and hair lotions is easy and fast. For creams, an extraction of salicylate is necessary. Relative standard deviations are less than 5.5% and the recoveries are between 95 and 105%.     

Determination of salicylate in blood serum by flow injection with immobilized salicylate hydroxylase

A flow injection (FI) enzymatic system, based on the use of immobilized salicylate hydroxylase in glass beads, was developed for the determination of salicylate. Salicylate hydroxylase and nicotinamide adenine dinucleotide (NADH) are used to convert salicylate to catechol. The reaction of catechol with 4-aminophenol at high pH yields a colored product which is detected spectrophotometrically at 565 nm. Ten samples of human serum containing from 5.0 x 10(-4) to 5.0 x 10(-3) mol/L added salicylate were analyzed and the recovery was determined. Eight additional serum samples containing salicylate were analyzed by the Trinder test and the proposed method. The results obtained with the 2 methods showed good agreement by the statistical Student's t-test. The relative precision of the method is about 3.4% (RSD of the mean recovery). Considering the lowest concentration analyzed, the quantitative limit of detection is about 0.2 x 10(-5) mol/L (3 x SD). The volume of the sample used was 150 microL. The proposed method was also used to analyze medicines containing acetylsalicylic acid. The results were statistically compared with those obtained through the U.S. Pharmacopoeia procedure and showed excellent agreement.     

Ion-selective electrode for salicylate assay in blood serum

A salicylate-selective membrane electrode made with heptyl-4-trifluoroacetylbenzoate as a neutral carrier was successfully applied for the determination of salicylate in blood serum. This procedure is advantageous because the free concentration of the drug in serum can be determined without sample preparation. The free salicylate concentrations determined by the ion-selective electrode compared to those obtained by conventional colorimetry gave a linear correlation coefficient 0.997 in the salicylate concentration range 0.1-2.5 mM.     

Flow injection amperometric detection of ascorbic acid using a Prussian Blue film-modified electrode

The PB film-modified electrode was used as an amperometric detector for flow injection analysis of ascorbic acid. The modified electrode detector showed good sensitivity, stability and reproducibility. The calibration curve for ascorbic acid was linear over the concentration range from 5.0x10(-6) to 1.0x10(-3) mol l(-1) with a slope of 19.9 mA mol(-1) per litre and a correlation coefficient of 0.999. The detection limit of this method was 2.49x10(-6) mol l(-1). The relative standard deviation of six replicate injections of 2.5x10(-4) mol l(-1) ascorbic acid was 2.5%. The results obtained for ascorbic acid determination in pharmaceutical products are in good agreement with those obtained by using the procedure involving the reaction between triiodide and ascorbic acid.     

Reagentless biosensor for isocitrate using one step modified Pt-Ir microelectrode

The Pt-Ir microelectrode modified through one step electropolymerization is proposed for the isocitrate amperometric biosensor construction. The enzyme (isocitrate dehydrogenase-ICDH), coenzyme (NADP(+)) and mediator (Meldola's Blue) were immobilized onto the microelectrode surface in one step from a PIPES buffer solution containing pyrrole. The optimized experimental conditions were 25 cycles of cyclic voltammetric in a solution containing 3.58 10(-5) mol l(-1) of mediator, 3.51 10(-4) mol l(-1) of coenzyme and 2.68 U ml(-1) of enzyme. In contrast to the biosensor for isocitrate reported in literature, just one enzyme was immobilized and no coenzyme addition in the solution of analysis was necessary. Catalytic currents were proportional to the isocitrate concentration between 7.7 10(-6) and 1.04 10(-4) mol l(-1), showing good repeatability. The detection limit of the proposed biosensor was 3.50 10(-6) mol l(-1), the response time was lower than 20 s, the lifetime was about 30 determinations and no significant interference of sugars and citric acid was verified. Orange juice samples were analysed by both methodology biosensor and spectrophotometric commercial kit, and the obtained results presented a good correlation. The data demonstrated that the developed biosensor is suitable for isocitrate determination in orange juice without matrix interferences.     

Potentiometric membrane electrode for salicylate based on an organotin complex with a salicylal Schiff base of amino acid.

A novel salicylate-selective electrode based on an organotin complex with a salicylal Schiff base of amino acid salicylaldehydeaminoacid-di-n-butyl-Sn(IV) [Sn(IV)-SAADB] as ionophore is described, which exhibits high selectivity for salicylate over many other common anions with an anti-Hofmeister selectivity sequence: Sal- > PhCOO- > SCN- > Cl04- > I- > NO3- > NO2- > Br- > Cl- > CH3COO-. The electrode, based on Sn(IV)-SAADB, with a 30.44 wt% PVC, a 65.45 wt% plasticizer (dioctyl phthalate, DOP), a 3.81 wt% ionophore and a 0.3 wt% anionic additive is linear in 6.0 x 10(-6) - 1.0 x 10(-1) mol l(-1) with a detection limit of 2.0 x 10(-6) mol l(-1) and a slope of 62.0 +/- 1.2 mV/decade of salicylate concentration in a phosphate buffer solution of pH 5.5 at 25 degrees C. The influence on the electrode performances by lipophilic charged additives was studied, and the possible response mechanism was investigated by UV spectra. The electrode was applied to medicine analysis and the result obtained has been satisfactory.     

Determination of acetylsalicylic acid by FIA-potentiometric system in drugs after on-line hydrolysis

A potentiometric flow injection (FI) system was developed for the acetylsalicylic acid (ASA) determination in drugs, without previous treatment. The tubular potentiometric electrode for salicylate (SA) was based on tricaprylyl-trimethyl-ammonium-salicylate (aliquat-salicylate) as the ion-exchanger, supported on poly(ethylene-co-vinyl-acetate) (EVA) matrix and applied directly onto a conducting support. The standards and samples were freshly prepared in ethanol solution (0.10 mol l(-1) Tris-SO(4) buffer, pH 8.0, containing 0.25 mol l(-1) Na(2)SO(4) and 8.0% v/v ethanol) to facilitate the dissolution of ASA and were injected directly into the system. The SA formed due to the on-line alkaline hydrolysis of alcoholic ASA solution, with 0.50 mol l(-1) NaOH (coil, 50 cm length), was monitored by the tubular electrode after neutralization with 0.25 mol l(-1) H(2)SO(4). A solution of 0.10 mol l(-1) Tris-SO(4) buffer (pH 8.0), containing 0.25 mol l(-1) Na(2)SO(4) was employed as carrier. In optimized conditions (flow rate of 2.1 ml min(-1) and volume of injection of 150 mul), the tubular electrode showed a linear response to ASA in the concentration range between 4.0x10(-3) and 4.0x10(-2) mol l(-1). A conversion factor of ASA to SA of 85% occurs in these conditions with an increase of about 130% in the signal to the system with on-line hydrolysis (three-channel) in comparison to the system without (one-channel). The response time of the electrode was about 5 s with an analytical frequency of 28 samples per h and a relative standard deviation (R.S.D.) of 2.1% for 30 successive injections. Determinations of ASA in tablet samples by the proposed method exhibited relative differences of 1.0-3.5%, compared to the official method of the British Pharmacopoeia. The useful lifetime of the sensor was greater than 1 month, in continuous use.     

Amperometric determination of acetylsalicylic acid in drugs by batch injection analysis at a copper electrode in alkaline solutions

This paper describes the determination of acetylsalicylic acid (ASA) as salicylate (SA) in pharmaceutical formulations by using amperometric detection with copper electrodes in 0.10 mol l(-1) NaOH solution. Batch injection analysis (BIA) was explored for this application. The system exhibited sharp current response peaks, rapid washout and excellent repeatability. A large linear dynamic range from 1 to 1000 mumol l(-1) was obtained by using an injected volume of 100 mul, with a detection limit of 0.48 mumol l(-1). R.S.D. of 0.37% for 30 repetitive (1x10(-4) mol l(-1)) injections and sampling frequency of 60 h(-1) were achieved. The results obtained using this system for ASA determination in seven different drug samples compared well with those found by spectrophotometry (Trinder test).     

Titania sol–gel-derived tyrosinase-based amperometric biosensor for determination of phenolic compounds in water samples. Examination of interference effects

For detection of phenolic compounds in environmental water samples we propose an amperometric biosensor based on tyrosinase immobilized in titania sol-gel. The analytical characteristics toward catechol, p-cresol, phenol, p-chlorophenol, and p-methylcatechol were determined. The linear range for catechol determination was 2.2 x 10(-7)-1.3 x 10(-5) mol L(-1) with a limit of detection of 9 x 10(-8) mol L(-1) and sensitivity 2.0 x 10(3) mA mol(-1) L. The influence of sample matrix components on the electrode response was studied according to Plackett-Burman experimental design. The potential interferents Mg(2+), Ca(2+), HCO3(-), SO4(2-), and Cl(-), which are usually encountered in waters, were taken into account in the examination. Cu(2+) was also taken into account, because CuSO(4) is sometimes added to a water sample, as a preservative, before determination of phenolic compounds. It was found that among the ions tested only Mg(2+) and Ca(2+) did not directly affect the electrode response. The developed biosensor was used for determination of catechol in spring and surface water samples using the standard addition method.     

A stable glucose biosensor prepared by co-immobilizing glucose oxidase into poly(p-chlorophenol) at a platinum electrode

An amperometric glucose biosensor was successfully developed by electrochemical polymerization of p-chlorophenol (4-CP) at a Pt electrode in the presence of glucose oxidase. The amperometric response of this biosensor to hydrogen peroxide, formed as the product of enzymatic reaction, was measured at a potential of 0.6 V (vs. SCE) in phosphate buffer solution. The performances of sensors, prepared at different monomer concentrations and polymerization potentials, were investigated in detail. The biosensor prepared under optimal conditions had a linear response to glucose ranging from 2.5 x 10(-4) to 1.5 x 10(-2) mol L(-1) with a correlation coefficient of 0.997 and a response time of less than 2 s. Substrate selectivity of the polymer-based enzyme electrode was tested for coexisting interferents such as uric acid and ascorbic acid, and no discernible response was observed. After 90 days, the response of the biosensor remained almost unchanged, indicating very good stability.     

Amperometric Biosensor for the Determination of Phenols Using a Crude Extract of Sweet Potato (Ipomoea Batatas (L.) Lam.)

Abstract

An amperometric biosensor for the determination of phenols is proposed using a crude extract of sweet potato (Ipomoea batatas (L.) Lam.) as an enzymatic source of polyphenol oxidase (PPO; tyrosinase; catechol oxidase; EC 1.14.18.1). The biosensor is constructed by the immobilization of sweet potato crude extract with glutaraldehyde and bovine serum albumin onto an oxygen membrane. This biosensor provides a linear response for catechol, pyrogallol, phenol and p-cresol in the concentration ranges of 2.0×10^?5-4.3×10^?4mol L^?1, 2.0×10^?5-4.3×10^?4 mol L^?1, 2.0×10^?5-4.5×10^?4 mol L^?1 and 2.0×10^?5-4.5×10^?4mol L^?1, respectively. The response time was about 3–5 min for the useful response range, and the lifetime of this electrode was excellent for fifteen days (over 220 determinations for each enzymatic membrane). Application of this biosensor for the determination of phenols in industrial wastewaters is presented.     

Enzyme sensor for L-lactate with a chitosan-mercury film electrode

Summary An amperometric enzyme sensor composed of a mercury film electrode and an enzyme-immobilized chitosan membrane is developed. This biosensor is based on both a mercury film electrode detecting the consumption of dissolved dioxygen following enzymatic reaction, and a chitosan membrane. The latter provides an excellent permselectivity and excludes electroactive interferents. The detection range of this biosensor was 1.0×10^–5–3.0×10^–4 mol/l and the relative standard deviation, R.S.D. at 5.0×10^–5 mol/l was 1.4% (n=3). This biosensor was applied to the direct determination of L-lactate in human serum without pretreatment.     

Rapid determination of lactulose in milk by microdialysis and biosensors

A simple and rapid flow system for the determination of lactulose in milk samples was developed. It is based on the hydrolysis of lactulose to galactose and fructose by the enzyme beta-galactosidase immobilised in a reactor. The amount of fructose produced was measured with an electrochemical biosensor based on the fructose dehydrogenase enzyme, K3[Fe(CN)6] as mediator and a platinum based electrochemical transducer. Parameters such as the enzyme immobilisation in the reactor and under the electrode surface, the lifetime of the beta-galactosidase reactor and of the dehydrogenase biosensor and the flow parameters were studied and optimised. Fructose was determined in the range 1 x 10(-6)-5 x 10(-3) mol l-1 with an RSD of about 2% and a detection limit of 5 x 10(-7) mol l-1. The use of a microdialysis probe as the sampling system permitted the direct measurement of lactulose in milk samples without pre-treatment in the range 1 x 10(-5)-5 x 10(-3) mol l-1. The sensitivity of the procedure allowed pasteurised, UHT and in-container sterilised milk to be distinguished.     

Determination of diclofenac sodium by capillary zone electrophoresis with electrochemical detection

Capillary zone electrophoresis was employed for the determination of diclofenac sodium using an end-column amperometric detection with a carbon fiber microelectrode, at a constant potential of 0.83 V vs. saturated calomel electrode. The optimum conditions of separation and detection are 4.90 x 10(-3) mol/l Na2HPO4-3.10 x 10(-3) mol/l NaH2PO4 (pH 7.0) for the buffer solution, 10 kV for the separation voltage, 5 kV and 10 s for the injection voltage and the injection time, respectively. The limit of detection is 2.5 x 10(-6) mol/l or 5.2 fmol (S/N=2). The relative standard deviation is 0.8% for the migration time and 4.7% for the electrophoretic peak current. The method was applied to the determination of diclofenac sodium in human urine.     

Carbon fiber cylindrical microelectrode-based detector for the determination of antithyroid drugs

An amperometric flow-injection method for the determination of antithyroid drugs such as 6-methyl-2-thiouracil (MTU) using a carbon fiber cylindrical microelectrode-based detector is reported. A home-made flow-cell specially adapted for working with cylindrical microelectrodes ranging between 4 and 10 mm in length was used for this purpose. Methanol containing 0.05 mol l(-1) tetrabutylammonium perchlorate as the supporting electrolyte was employed, and a potential of +1.6 V was selected for the amperometric detection of MTU. No cleaning or electrode surface regeneration of the fiber was necessary during the whole working day. A limit of detection of 2.6x10(-7) mol l(-1) (37 mug MTU l(-1)) was achieved. The method was applied to the determination of MTU in spiked feed samples (peas and corn flour), at the 142 mug g(-1) level. The procedure involved the extraction of the drug in methanol, a clean-up step using Florisil cartridges and the use of the standard additions method. Recoveries of 81+/-6 and 85+/-8% were obtained for peas and corn flour, respectively.     

Monitoring human serum transferrin by capillary zone electrophoresis with end-column amperometric detection

Capillary zone electrophoresis was employed for the determination of human serum transferrin using end-column amperometric detection with a carbon fiber microelectrode at a constant potential of 1.9 V vs. saturated calomel electrode (SCE). The optimum conditions of separation and detection are 7.5 x 10(-4) mol/L Tris-3.44 x 10(-4) mol/L HCl for the buffer solution, 20 kV for the separation voltage, 5 kV and 10 s for the injection voltage and the injection time, respectively. The limit of detection is 6.7 x 10(-8) mol/L or 440 amol (S/N = 2). The relative standard deviations are 0.67% for the migration time and 1.5% for the electrophoretic peak current. The method was applied to the determination of transferrin in human serum. The recovery is between 93-104%.     

2,4,6-tri(3,5-Dimethylpyrazoyl)-1,3,5-triazine modified carbon paste electrode for trace Cobalt(II) determination by differential pulse anodic stripping voltammetry

A differential pulse anodic stripping voltammetry was developed for the sensitive and selective determination of Co(II) at 2,4,6-tri(3,5-dimethylpyrazoyl)-1,3,5-triazine modified carbon paste electrode in 0.1 mol l(-1) NH(4)Cl solution (pH 4.95). The oxidation peak of Co(II) was observed at 0.03 V(vs. Ag/AgCl) by scanning the potential in a positive direction. The analysis procedure consisted of an open circuit accumulation step in stirred sample solution. This was followed by medium exchange to a clean solution and subsequently an anodic potential scan was effect to obtain the voltammetric peak. The current was proportional to the concentration of the Co(II) ion in a range of 1x10(-8)-1x10(-6) mol l(-1) for 3 min accumulation and in the range of 1x10(-9)-1x10(-8) mol l(-1) for 5 min accumulation; most of metal ions do not interfere with the determination. The developed method was applied to Co(II) determination in potable water.     

Determination of trace procaine hydrochloride by differential pulse adsorptive stripping voltammetry with a Nafion modified glassy carbon electrode.

A sensitive and selective method for the determination of procaine hydrochloride with a Nafion-modified glassy carbon electrode has been developed. The voltammetric behavior of procaine hydrochloride on the Nafion-modified electrode indicated that the modified electrode not only increased the sensitivity of the determination of procaine hydrochloride, but also catalyzed the electrode process. Procaine hydrochloride was accumulated in Britton-Robinson buffer (pH 2.09) at a potential of -0.2 V (vs. SCE) for 180 s, and was then determined by differential pulse adsorptive stripping voltammetry. The effect of various parameters, such as the pH of the medium, the mass of drop-coated Nafion, the accumulation potential, the accumulation time and the scan rate, were investigated. Under the optimum conditions, a linear calibration graph was obtained in the concentration range of 6.0 x 10(-8) to 6.0 x 10(-6) mol l(-1) with a correlation coefficient of 0.9987. The relative standard deviation was 4.18% for eight successive determinations of 1.0 x 10(-7) mol l(-1) procaine hydrochloride, and the detection limit (three times signal to noise) was 7.0 x 10(-9) mol l(-1). A study of interfering substances was also performed, and the method was applied to the direct determinations of procaine hydrochloride in the injection solution of procaine hydrochloride and in rabbit serum.     

Ceramic Carbon/Polypyrrole Materials for the Construction of Bienzymatic Amperometric Biosensor for Glucose

Amperometric enzymatic biosensors have high selectivity and simplicity in use. It has advantages over other analytical methods in biochemistry, pharmacology, so it evokes strong interests1,2. Generally, the detection mode involved in oxidase based biosensors is often based on the electrochemical detection of hydrogen peroxide directly3,4. However the direct oxidation of hydrogen peroxide requires a relative high working potential (exceeding ca. 0.6 V vs. SCE), at which many biological sub…