(二苯甲酰甲烷基)(环戊二烯基)二氯化钛/MgCl2-SiO2/MAO中各组分对乙烯聚合的影响

研究开发了一种新型非茂负载乙烯聚合催化剂 CpTi(dbm)Cl2 MgCl2 SiO2 MAO ,并考察了该催化剂中各组分对乙烯聚合活性的影响 .结果表明 ,SiO2 不仅可以改善催化剂的流动性和分散性 ,还有益于提高催化活性 .MgCl2 对活性中心有一定化学改性作用 ;MgCl2 、SiO2 和CpTi(dbm)Cl2 的比例的变化对载体型催化剂的催化活性有一定影响作用 ;采用适量的MAO对复合载体MgCl2 SiO2 活化 ,能提高催化活性 .用ZnCl2 MAO对SiO2处理制成的复合载体催化剂CpTi(dbm)Cl2 MgCl2 ZnCl2 SiO2 MAO ,可以提高催化活性 ,“锌调”作用明显 ,随着锌化合物含量的增加 ,聚合物相对分子质量下降 ,相对分子质量分布加宽 ,并且其催化活性也增加 .     

球形氯化镁载体与四氯化钛反应的载钛过程研究

球形氯化镁载体型齐格勒-纳塔催化剂是目前常用的工业聚烯烃催化剂,由于制备工艺对催化剂性能影响很大,因此对此类催化剂制备过程的研究具有重要意义。本文利用自制球形氯化镁载体与四氯化钛反应制备球形聚烯烃催化剂,分析了载钛反应过程的中间产物。对球形氯化镁载体载钛过程中钛含量、比表面、比孔容、晶型等发生的变化进行分析,并研究了邻苯二甲酸二丁酯作为内给电子体在球形氯化镁载体载钛过程中的作用,为球形氯化镁载体型催化剂制备工艺的改进提供了重要参考依据。     

石墨烯/二氯化镁负载钛系齐格勒-纳塔催化剂制备及其乙烯聚合性能

石墨烯自2004年发现以来,由于其独一无二的优异性迅速成为科学家们的研究热点.由于石墨烯具有极其优异的电学、力学和热学等性能,因此被广泛应用于高性能聚合物基复合材料的制备.众所周知,纳米填料在聚合物中的分散状态以及与基体间的界面作用是构筑高性能聚合物纳米复合材料的关键因素.由于石墨烯极易团聚,难以通过传统的熔融共混法制备均匀分散的石墨烯增强-聚烯烃纳米复合材料.另一方面,聚烯烃通常需要在较高温度下才能溶于部分有毒溶剂(如:三氯苯和二甲苯等),因此溶液共混法也不适用于聚烯烃-石墨烯纳米复合材料的制备.有鉴于此,本文开发了一种共沉积法制备石墨烯/二氯化镁负载钛系齐格勒-纳塔催化剂的路线.通过原位聚合直接制备出石墨烯均匀分散的聚烯烃/石墨烯纳米复合材料.考察了石墨烯的加入量对催化剂形态及其催化乙烯聚合行为的影响.当石墨烯加入量较低时,多个石墨烯片被包裹于较大的催化剂粒子中.随着石墨烯加入量的增加,催化剂趋向于在石墨烯表面聚集.继续增加石墨烯量将导致石墨烯包裹催化剂粒子,降低过渡金属钛的负载效率.通过三乙基铝活化后,所制备的催化剂具有非常高的乙烯催化活性,所生成的聚乙烯/石墨烯纳米复合材料复制了催化剂的片状结构.同时,通过对所制备的聚乙烯/石墨烯纳米复合材料进行电子显微镜和X射线衍射分析可知,石墨烯均匀分散于聚乙烯基体中,并且没有任何团聚现象发生.该复合材料的热重分析表明,仅加入非常少量的石墨烯就可以使其具有比纯聚乙烯更高的热稳定性,当石墨烯加入量为0.66 wt%时,其5 wt%热分解温度较纯聚乙烯升高了54°C.同时,所制备聚乙烯/石墨烯纳米复合材料具有更优异的机械性能.因此,本研究提供了一个简单高效的高性能聚烯烃/石墨烯纳米复合材料的制备方法.     

烷基铝对球形MgCl_2负载的茂金属催化剂催化乙烯聚合的影响

以甲基铝氧烷(MAO)为助催化剂的茂金属催化剂虽然具有催化活性高、分子量分布窄、聚合物化学组成均匀等优点,但其极高的Al/Zr比和聚合物颗粒形态差等缺点限制了其工业化应用,因此对茂金属催化剂的负载化成为近年来的研究热点.在众多的载体中,球形MgCl2是研究得很少的一类载体,文献中曾采用先负载主催化剂茂金属配合物,聚合时再加入助催化剂MAO的方法[1],由于加入的MAO与主催化剂的络合能力很强,会使部分载上的主催化剂溶解下来,成为均相聚合[2,3],导致聚合物颗粒形态差,且粘釜现象严重.我们则采用相反的思路,即先将助催化剂MAO负载在球形MgCl2上,制得MgCl2/MAO,在聚合前再将MgCl2/MAO与Et[Ind]2ZrCl2混合陈化,并立即在少量烷基铝活化下引发乙烯聚合[4],实验结果表明,该催化剂聚合活性高、聚合物的颗粒形态好、且不粘釜,是一种新型的载体催化剂.由于烷基铝的加入可使催化剂的活性大幅度提高,所以本文将烷基铝也称作助催化剂,来研究其对该载体催化剂催化乙烯聚合的影响.     

Gas Phase Polymerization of Ethylene with Supported Titanium-Nickel Catalysts

A new ditransition-metal catalyst system TiCl4-NiCl2/MgCl2-SiO2/AlR3 was prepared.Gas phase polymerization of ethylene with the catalysts has been studied.The kinetic curves of gas phase polymerization showed a decline.The catalystic efficiency and polymerization reaction rates have a optimum value when Ni content of the catalysts was 12.5%(mol).The products obtained are branched polyethylene.     

MgCl2/R'nAl(OR)3-n: an excellent activator/support for transition-metal complexes for olefin polymerization

A new and effective method for the activation, and simultaneously, immobilization of bis(phenoxyimine) early-transition-metal complexes for olefin polymerization (known as FI catalysts), which makes use of MgCl(2)/R'(n)Al(OR)(3-n) as an activator/support, has been developed. Ti-, Zr-, and V-FI catalysts combined with this MgCl(2)-based compound can form highly active MgCl(2)-supported single-site catalysts capable of demonstrating superior catalytic properties, compared to the corresponding homogeneous methylaluminoxane- (Ti- and Zr-FI catalysts) or alkylaluminum-activation systems (V-FI catalysts), in terms of their catalytic activity, molecular weight, stereoselectivity, and comonomer incorporation. Additionally, these new catalysts can produce polymers of significant morphology with high efficiency. Notably, the MgCl(2)-based compounds can also effectively activate and immobilize the early-to-late transition-metal complexes that have emerged recently. Thus, the application of MgCl(2)-based compounds as activators/supports for transition-metal complexes for olefin polymerization provides a conceptually new strategy for the development of methylaluminoxane- and borate-free, high-performance, single-site catalysts capable of controlling polymer morphology.     

新型高活性催化剂乙烯气相聚合的研究(Ⅱ)──改性剂、预聚合和聚合条件对乙烯气相聚合的影响

研究了新型高活性乙烯气相聚合催化剂TiCl₄/MgCl₂/ZnCl₂/SiCl₄/醇/Al(i-Bu)₃体系中不同醇、不同C₂H₅OH/Ti摩尔比和正丁醚对聚合反应及产物颗粒形态的影响。研究了预聚合反应及乙烯气相聚合反应规律。用扫描电镜和图象分析对催化剂、预聚物及聚合产物的形态和颗粒分布的研究结果表明:新型高活性催化剂和经预聚合制得的乙烯气相聚合物的颗粒形态类似球形,颗粒长短轴比值和大小粒径比值相近。     

核壳结构Ziegler-Natta复合催化剂的制备及其乙烯聚合

采用溶胶-凝胶法,将聚(苯乙烯-co-丙烯酸)(PSA)膜材料和氯化镁的复合物包覆在以硅胶为载体的TiCl3催化剂上,负载TiCl4后制得Ziegler-Natta复合催化剂.采用红外光谱、激光粒度仪和扫描电镜对催化剂进行了表征,结果表明该复合催化剂呈核壳结构.同时,考察了复合催化剂中膜的厚度和反应中的氢气含量对催化剂的聚合活性和聚乙烯性能的影响,实验发现,膜厚约为3μm的核壳结构复合催化剂活性良好,其具有带诱导期的平稳型动力学曲线;膜厚1.5μm的复合催化剂的活性接近于实验所用的以硅胶为载体的TiCl3催化剂,且其具有相似的衰减型动力学曲线.研究同时表明,不同的膜厚能够调节复合催化剂的氢调性能及所得聚乙烯的分子量分布.     

给电子体在制备烯烃聚合NdCl_3载体催化剂中的作用

<正> Martin以无水稀土氯化物为载体,与磷酸三丁酯(TBP)在庚烷溶剂中反应制得LnCl_3/TBP/TiCl_4载体催化剂,其中以NdCl_3为载体的催化剂对乙烯聚合有很高活性,但对TBP的作用和载钛结构涉及较少。NdCl_3为链状晶体结构,不同于层状晶体结构的MgCl_2和TiCl_3(α和δ型)。我们对NdCl_3/EtOH/TiCl_4催化剂进行了较为详细的研究,并与MgCl_2/EtOH/TiCl_4催化剂进行比较,发现NdCl_3载体催化剂与MgCl_2载体     

用高效SiO2载体催化剂进行乙烯气相聚合

使用球形ＳｉＯ２负载ＭｇＣｌ２－ＴｉＣｌ４高活性催化剂进行乙烯气相聚合，考察了催化剂制备条件和添加剂对催化剂的组成、催化活性以及聚合表观动力学的影响．结果表明，ＳｉＯ２热处理温度和所用的醇对Ｍｇ和Ｔｉ的负载量及乙烯聚合活性有明显的影响．催化剂制备中添加Ｌｅｗｉｓ酸ＳｉＣｌ４或ＡｌＥｔ２Ｃｌ能大幅度提高催化剂的活性，其中以ＳｉＣｌ４的效果最为明显．随着ＳｉＣｌ４用量的增加，乙烯气相聚合的活性显著提高，聚合速度随时间变化由渐升平稳型转变为衰减型     

High-temperature single-site ethylene polymerization behavior of titanate complexes supported by 1,3-bis(3,5-dialkylpyrazol-1-yl)propan-2-olate ligation

Titanate(1-) complexes Na[(THF)(kappa1-O-bdbpzp)TiCl4] (1) and Na[(THF)(kappa1-O-bdmpzp)TiCl4] (2) and titanate(2-) complexes [Na(THF)]2[(kappa1-O-bdbpzp)2TiCl4] (4) and [Na(THF)]2[(kappa1-O-bdmpzp)2TiCl4] (5) were obtained in good yield from reaction of Na[bdbpzp] or Na[bdmpzp] (sodium salt of 1,3-bis(3,5-di-tert-butylpyrazol-1yl)propan-2-ol or 1,3-bis(3,5-dimethylpyrazol-1yl)propan-2-ol) with TiCl4 (in the appropriate molar ratio) at 0-25 degrees C. Protonolysis of TiCl4 with 1 equiv of bdmpzpH furnished related zwitterionic titanate(1-) complex 3 that possessed a kappa2-N,O-coordinated pyrazolyl-alkoxide with pendant pyrazolium group. Methylalumoxane (MAO) activation of 1-5 under high-temperature solution polymerization conditions produced active single-site ethylene polymerization catalysts that exhibit considerably higher thermal stability (especially 2/MAO, 3/MAO, and 5/MAO) than previously reported for Cp2TiCl2/MAO or Ti catalysts supported by related heteroscorpionate or scorpionate ligation.     

球形MgCl2负载的MAO/rac-Et[Ind]2ZrCl2催化剂催化丙烯 聚合

采用只在球形MgCl2上负载MAO,聚合前再同rac--Et[Ind]2ZrCl2预混的负载方式进行丙烯聚合。在少量AlEt3的活化下,很低的Al(MAO)/Zr摩尔比时即可获得比均相催化剂高一个数量级的活性,考察了温度、压力、Al(MAO)/Zr摩尔比和催化剂浓度对聚合的影响,同时用13^CNMR测定了均相和载体催化体系所制备的聚丙烯的微结构,发现负载型茂金属催化剂制得的聚丙烯立构规整性高于均相体系,其五元组立构序列[mmmm]可从均相的52.6%提高到负载催化剂的79.5%。扫描电镜观察表明,聚合物颗粒可较好地复制球形催化剂的颗粒形态。     

用于丙烯聚合的MgCl2负载Ziegler-Natta催化剂研究进展

综述了用于丙烯聚合的MgCl2负载Ziegler-Natta催化剂研究进展,包括内给电子体的发展及其作用研究,催化剂活性中心的模型,用MgCl2负载的Z-N催化剂制备抗冲聚丙烯合金.     

球形MgCl_2负载的MAO-Et[Ind]_2ZrCl_2催化剂用于乙烯聚合的动力学研究

以Al(i Bu) 3 为活化剂 ,对球形MgCl2 负载的MAO Et[Ind]2 ZrCl2 催化剂用于乙烯淤浆聚合的动力学进行了研究 .确定了动力学控制条件后 ,测定了聚合反应级数和表观活化能 ,用动力学外推法计算出活性中心浓度和链增长速率常数 ,用扫描电镜观察了聚合过程中聚合物形态的变化 ,发现聚合是在催化剂的次级粒子上进行 ,催化剂粒子无明显破碎     

α-二亚胺镍(Ⅱ)配合物-TiCl4复合催化剂催化乙烯原位聚合制备支化聚乙烯

制备了α-二亚胺镍()配合物[C6H5—NC(CH3)—C(CH3)N—C6H5]NiBr2(NiL)-TiCl4负载在MgCl2-SiO2载体上的复合催化剂(NiL-TiCl4/MgCl2-SiO2),以AlR3为助催化剂(不用MAO)催化乙烯聚合.研究了NiL和TiCl4负载方法、NiL/TiCl4摩尔比、助催化剂种类及聚合反应温度等对催化剂性能的影响.用IR和13CNMR表征聚合产物支化度及支链结构;用GC-MS监测聚合反应.实验结果表明,NiL-TiCl4复合催化剂具有齐聚原位共聚特性,可催化乙烯原位聚合,合成支化聚乙烯.     

Modification of the(SiO_2/MgO/MgCl_2)·TiCl_x Ziegler-Natta Polyethylene Catalysts Using the Third Metal Elements

Various(SiO_2/MgO/MgCl_2)·Ti Clx Ziegler-Natta catalysts modified by the third metal elements were synthesized by the co-impregnation of water-soluble magnesium and the third metal salts. Several key factors including the electronegativity of the third metal elements, catalyst performances in ethylene homo-polymerization, ethylene/1-hexene copolymerization and hydrogen response were systematically investigated. Both the catalyst performance and the polymer properties are influenced by the introduction of the third metal elements. Compared with the unmodified(SiO_2/MgO/MgCl_2)·Ti Clx Ziegler-Natta catalyst, activity and 1-hexene incorporation are enhanced by the introduction of zirconium, vanadium, aluminum and chromium, while deteriorated by the addition of ferrum, nickel, molybdenum and tungsten. Correlations of the catalyst activities and 1-hexene incorporation ability with the electronegativity of the third metal elements are discovered. It is found that the lower electronegativity of the third metal elements leads to the catalyst with higher activity and higher α-olefin co-polymerization ability. The polyethylene produced by a nickel modified catalyst showed broad molecular weight distribution(MWD) and the lowest average molecular weight(MW), while by using a ferrum modified catalyst, the resulting polyethylene had the highest MW, reaching the ultra-high MW area. Vanadium and chromium modified catalysts demonstrated the best hydrogen response.     

SYNTHESIS OF BRANCHED POLYETHYLENE USING (α-DIIMINE)NICKEL(Ⅱ)TiCl4 COMBINED AND SUPPORTED CATALYST*

(α-Diimine)nickel(Ⅱ) {[C6H5 -N = C(CH3)-C(CH3) = N -C6H5]NiBr2}-TiCl4 abbreviated as NiL-TiCl4 combined catalyst which is supported on MgCl2-SiO2 carrier has been prepared, by using alkyl aluminum (AIR3) as the cocatalyst in place of methylaluminoxane (MAO) to catalyze ethylene oligomerization and copolymerization in situ. The influences of procedure for supporting NiL-TiCI4, the molar ratio of NiL to TiCI4, cocatalyst type and polymerization temperature on the catalytic performance were studied. The degree of branching and the composition of the branched chain of polymers produced have been investigated by IR and ^13C-NMR spectra. The results show that the combined catalyst can synthesize the branched polyethylene with various banched chains .The polymerization reaction was monitored by gas chromatography and mass spectrometry (GC-MS). The results show that this catalyst promotes the oligomerization and copolymerization in situ for ethylene.     

Characterization of the changes in the initial morphology for MgCl2-supported Ziegler-Natta polymerization catalysts

Recently considerable detail has become available on the initial morphology and the morphological changes that occur for silica based Cr catalysts for ethylene polymerization. These catalysts are produced as a dry powder and may be employed either in gas phase or in slurry processes. MgCl₂-supported Ziegler-Natta polymerization catalysts are often prepared and employed as slurries. They usually are never dried and thus few studies have employed the spectra of physical techniques common to the characterization of pore structure. In the current study, we have carefully removed the solvent for both ball-milled and precipitated MgCl₂-supported catalysts. These catalysts are characterized by physical sorption, mercury porosimetry, and electron microscopy both as prepared and during the initial stages of polymerization (to ～ 100 g of polymer/g of catalyst). We find that the initial catalyst may be represented by a complex agglomerate of small crystallites as contrasted with the branched pore network found in Cr/silica catalysts. As a result, it is concluded that the initial fragmentation of the MgCl₂ based systems is more uniform as contrasted with the progressive fragmentation of the silica-based system. This fragmentation mechanism facilitates the retention of greater polymer/catalyst surface during the initial stages of the polymerization. © 1992 John Wiley & Sons, Inc.     

由Mg(nBu)2制备的MgCl2载体催化剂的烯烃聚合动力学

讨论了催化剂ＣＤ，ＣＭ和ＣＤ－Ａ的乙烯和丙烯聚合动力学曲线，只有催化剂ＣＤ在丙烯聚合时加入外给电子体其动力学曲线为上升－衰减型，其它均为衰减型，催化剂ＣＤ丙烯聚合活性高于催化剂ＣＭ。丙烯聚合时加入外给电子体使总活性中心浓度降低，但等规中心浓度反应增加。同种载体制备的催化剂ＣＤ和ＣＤ－Ａ载钛过程中加入内给电子体，可使其聚合活性增加，在一定范围内，随Ａｌ／Ｔｉ增加，在一定范围内，随Ａｌ／Ｔｉ增加，催化     

以SIO~2为载体的乙烯丙烯共聚高效Ziegler-Natta催化剂

本工作以反应法制备了sio~2负载的乙丙烯共聚高效ziegler-natta催化剂, 考察了Ticl~4/Al~2t~3l~3/Sio~2催化体系的催化效率,发现在无Mgcl~2及Mg系化合物存在下,使催化活性大大提高,并利用ESR对高效的原因进行了初步探讨,得到了一些有意义的结果.