Thermal reduction and reoxidation of spinel-type Cu1−xZnxAl2O4

The thermochemical reactivity of the spinel-type quaternary metal oxide Cu_1–xZn_xAl₂O₄ has been investigated for different Cu:Zn ratios. In oxygen or inert gas atmospheres no considerable reduction is observed. In molecular hydrogen metal selective reduction of the Cu is found at relatively high temperature. The solid reduction product is made up of sintered, poorly dispersed metallic copper on a Zn-Al-O metal oxide support, a potential catalyst for the methanol synthesis. Owing to the measured high reduction temperature leading to the mentioned sintering of the metallic copper, the activity of this system cannot be high.Financial support by the Swiss National Science Foundation under project Nr. 2027933.89 is gratefully acknowledged.     

Thermo-programmed reduction study of Pt/WO<Subscript>x</Subscript>–ZrO<Subscript>2</Subscript> materials by thermogravimetry

The thermo-programmed reduction study of Pt/WO_x–ZrO₂ materials prepared with different tungsten loading were performed by thermogravimetry. The samples were synthesized by impregnation method and calcined at 600, 700 and 800°C. The characterizations of both un-calcined and calcined materials were carried out using different techniques: thermal analysis (TG and DTA), X-ray diffraction (XRD) and thermo-programmed reduction (TPR). TG and DTA analysis of un-calcined were used to determination of calcination temperatures of the samples. XRD diffractograms were useful to help us in the determination of phase presents. TPR profiles showed between three and four events at different temperatures attributed to platinum reduction and the different stages of tungsten specie reduction.     

K2CO3促进苯并呋喃单元3-位与硫酚构建C-S键

本文在前期工作基础上进一步考察了2-位支链酮苯并呋喃单元在3位与硫酚构建C-S键的反应。研究发现,以K₂CO₃作碱,苯并呋喃单元2-位官能团为不同链长的脂肪酮时能高效地合成各种不同取代基的3-芳硫基苯并呋喃衍生物,所得产物经核磁共振、HRMS等方法进行了表征。该反应具有条件温和、底物适用范围广、操作简单、产率高、环境友好等优点,可为含有芳香烃硫基取代的天然产物及复杂药物分子的合成提供潜在的合成途径。     

系列硅铝比纳米薄层ZSM-5分子筛的合成和表征

以自制不对称双子季铵盐表面活性剂为模板, 在水热合成体系中控制合成系列硅铝比纳米薄层ZSM-5分子筛.采用X射线衍射(XRD)、N₂吸附-脱附、X射线荧光光谱(XRF)、扫描电镜(SEM)和²⁷Al魔角旋转核磁共振(²⁷Al MAS-NMR)对合成的样品进行了表征. 详细研究了晶化温度、晶化时间、结构导向剂(SDA)用量、碱度等对合成的影响和纳米薄层ZSM-5分子筛的形成过程. 结果表明: 分子筛硅铝比越高, 结构导向剂用量越大, 所需的晶化时间越短; 晶化温度越高, 晶化时间越短; 且不同硅铝比纳米薄层ZSM-5分子筛的形貌规整度、比表面积和介孔/微孔孔容比例随着硅铝比而变化.     

LaNiO2: Synthesis and structural characterization

The preparation of a single phase LaNiO₂ by controlled H₂ reduction of the perovskite LaNiO₃ is reported. The different steps of the synthesis are detailed. The structural characterization is made by X-ray diffraction (XRD) and neutron powder diffraction (NPD) and discussed; the derived crystal structure is the infinite-layer CaCuO₂. Both XRD and NPD patterns are characterized by anisotropic shape broadening originating from size effect linked to the reduction process. From NPD, the LaNiO₂ powder is composed of platelet-like crystallites having an average thickness equal to 20 nm along the [001] direction. A modulation of the neutron diffraction background is observed and discussed in connection to the reduction process.     

Monolith Manganese-Based Catalyst Supported on ZrO2-TiO2 for NH3-SCR Reaction at Low Temperature

Monolith catalysts were prepared using TiO₂ and ZrO₂-TiO₂ as supports with MnO₂ as active component and Fe₂O₃ as promoter. The catalytic activities at low temperature and stability at high temperature for selective catalytic reduction of NO_x with NH₃ (NH₃-SCR) in the presence of excessive O₂ were studied after the catalysts calcined at different temperatures. The catalysts were characterized by X-ray diffraction (XRD), specific surface area measurements (BET), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results indicated that the catalyst supported on ZrO₂-TiO₂ had excellent stability at high temperature, and possessed high specific surface area and oxygen storage capacity, and had strong redox property. The results of the catalytic activities indicated that the monolith manganese-based catalyst using ZrO₂-TiO₂ as support had evidently improved the activity of NH₃-SCR reduction reaction at low temperature, and it showed great potential for practical application.     

Tricyclic Pyrazole-Based Compounds as Useful Scaffolds for Cannabinoid CB1/CB2 Receptor Interaction

Cannabinoids comprise different classes of compounds, which aroused interest in recent years because of their several pharmacological properties. Such properties include analgesic activity, bodyweight reduction, the antiemetic effect, the reduction of intraocular pressure and many others, which appear correlated to the affinity of cannabinoids towards CB₁ and/or CB₂ receptors. Within the search aiming to identify novel chemical scaffolds for cannabinoid receptor interaction, the CB₁ antagonist/inverse agonist pyrazole-based derivative rimonabant has been modified, giving rise to several tricyclic pyrazole-based compounds, most of which endowed of high affinity and selectivity for CB₁ or CB₂ receptors. The aim of this review is to present the synthesis and summarize the SAR study of such tricyclic pyrazole-based compounds, evidencing, for some derivatives, their potential in the treatment of neuropathic pain, obesity or in the management of glaucoma.     

EU-1分子筛的合成及其在正己烷异构化反应中的催化性能

在不同硅铝比(nSiO₂/nAl₂O₃)的合成凝胶(含纯硅凝胶)中引入晶种,合成了纯相的EU-1分子筛。研究了铝源、模板剂和晶种添加量对EU-1分子筛的结晶度、形貌尺寸等的影响;重点研究了不同硅铝比对样品结晶度、晶粒尺寸、酸性、比表面积和孔容等的影响。将合成结果绘制成了纯相EU-1分子筛的合成条件三元图,从三元图可看出,晶种法可显著扩大纯相EU-1分子筛的合成区域。将Pt/H-EU-1用于正己烷异构化反应,结果表明,该催化剂具有优异的正己烷异构化活性及稳定性,对异构烷烃有较高的选择性。     

EU-1分子筛的合成及其在正己烷异构化反应中的催化性能

在不同硅铝比(n_SiO2/n_Al2O3)的合成凝胶(含纯硅凝胶)中引入晶种,合成了纯相的EU-1分子筛。研究了铝源、模板剂和晶种添加量对EU-1分子筛的结晶度、形貌尺寸等的影响;重点研究了不同硅铝比对样品结晶度、晶粒尺寸、酸性、比表面积和孔容等的影响。将合成结果绘制成了纯相EU-1分子筛的合成条件三元图,从三元图可看出,晶种法可显著扩大纯相EU-1分子筛的合成区域。将Pt/H-EU-1用于正己烷异构化反应,结果表明,该催化剂具有优异的正己烷异构化活性及稳定性,对异构烷烃有较高的选择性。     

铜物种对Cu/Fe2O3水煤气变换反应催化剂性能的影响

采用共沉淀法制备了系列铜负载量不同的Cu/Fe₂O₃水煤气变换(WGS)催化剂,并考察了铜负载量对催化剂结构和水煤气变换反应性能的影响. 结果表明,Cu/Fe₂O₃催化剂呈现出良好的水煤气反应性能,当CuO质量分数为20%时,催化剂的WGS性能最优,250 ℃时CO转化率高达97.2%,同时热稳定性也最好. 运用X射线粉末衍射(XRD)、N₂物理吸脱附和H₂程序升温还原(H₂-TPR)等手段对Cu/Fe₂O₃催化剂的物相、织构特征及还原性能进行了表征,结果表明,CuFe₂O₄物种的存在极大地改善了催化剂的还原性能和WGS反应活性. 这是由于CuFe₂O₄特殊的尖晶石结构有利于Cu微晶的稳定;同时,CuFe₂O₄在低温下即被还原为单质铜,有利于促进催化剂体系中电子的转移. 此外,通过(NH₄)₂CO₃溶液处理,研究了独立相CuO对Cu/Fe₂O₃催化剂WGS反应性能的影响,结果发现,独立相CuO的存在,有利于H原子在各组分传递,从而促进催化剂的CuFe₂O₄的还原,改善Cu/Fe₂O₃催化剂的WGS反应性能.     

Fe3O4-Graphene oxide nanocomposite: Synthesis of 5-sulfanyl tetrazole derivatives of alkyls,indoles, and pyrroles

In this work, the use of Fe₃O₄/geraphene oxide nanocomposite as an efficient catalyst for the synthesis of 5-sulfanyltetrazole derivatives of indoles, pyrroles, and 5-alkyl sulfanyltetrazoles is described. These compounds are readily obtained by the reaction of the starting heterocycles indoles, N-aryl pyrroles, alkyl thiocyanates, and trimethylsilyl azide in good to excellent yields. Moreover, Fe₃O₄/GO nanocomposite could be easily separated from the reaction mixtures by an external permanent magnet and reused at least six times continuously without significant reduction in the product yield and its catalytic activity.     

Synthesis and thermal investigation of Na2Cd(SO4)2·2H2O

The synthesis and thermal decomposition of Na₂(SO₄)₂·2H₂O in both air and nitrogen are described. The synthesis was performed by two different procedures, but in both cases the same product was obtained, corresponding to the general formula given above. The crystals obtained were investigated by methods of X-ray powder diffraction, and chemical and thermal analysis. The differences in thermal decomposition in air and nitrogen are discussed.     

Preparation and photocatalytic activity of high-efficiency visible-light-responsive photocatalyst SnSx/TiO2

Visible-light-responsive composite photocatalysts SnS₂/TiO₂ and SnS/TiO₂ with different mass ratios were prepared by in-situ synthesis technology in solution with commercial TiO₂. The junction-based materials SnS_x (x=1, 2)/TiO₂ were found to have high visible-light photocatalytic performance and possess much better activity than the single-phase SnS_x or TiO₂. The greatly enhanced photocatalytic activity of the SnS_x/TiO₂ composites was mainly attributed to the matching band potentials and efficient charge transfer and separation at the tight-bonding interface between SnS_x and TiO₂. The fact was confirmed by the comparison of photocatalytic activities of the SnS₂/TiO₂ samples prepared by physical mixing method and in-situ synthesis technique.     

Direct syntheses of Lan+1NinO3n+1 phases (n=1, 2, 3 and ∞) from nanosized co-crystallites

A new direct route for the “bottom up” syntheses of phases in the La_n+1Ni_nO_3n+1 series (n=1, 2, 3 and ∞) has been achieved via single-step heat treatments of nanosized co-crystallized precursors. The co-crystallized precursors were prepared using a continuous hydrothermal flow synthesis system that uses a superheated water flow at ca. 400 °C and 24.1 MPa to produce nanoparticulate slurries. Overall, a significant reduction in time and number of steps for the syntheses of La₃Ni₂O₇ and La₄Ni₃O₁₀ was achieved compared with more conventional synthesis methods, which typically require multiple homogenization and reheating steps over several days.     

Removal of Phenol Dyes Using a Photocatalytic Reactor with SnO2/Fe3O4 Nanoparticles

In this study, we present kinetics of phenol dyes removal by SnO₂/Fe₃O₄ nanoparticles in a photocatalytic reactor for optimization of this process. The effect of different concentrations of SnO₂ 5, 10, 15, 20% w/w on the photocatalytic reactor during removal of phenol red was investigated. The SnO₂/Fe₃O₄ nanoparticles were synthesized by core–shell method. The results of XRD and TEM showed the successful synthesis of these nanoparticles. Several other methods were applied to synthesis of these nanoparticles but none of them succeeded. This process composed of two-stage. The first stage was absorption by iron oxide nanoparticles and second stage was photocatalytic by tin oxide nanoparticles that followed pseudo-second-order kinetic and first-order kinetic, respectively. Optimization of this process was done corresponding to the parameters affecting the process with design expert software. In order to determine the optimal values of each of the parameters and the optimal conditions of the process, parameters were introduced to response surface methodology.     

Hydrothermal crystal growth of the potassium niobate and potassium tantalate family of crystals

Single crystals of KNbO₃ (KN), KTaO₃ (KT), and KTa_1−xNb_xO₃ (x=0.44, KTN) have been prepared by hydrothermal synthesis in highly concentrated KOH mineralizer solutions. The traditional problems of inhomogeneity, non-stoichiometry, crystal striations and crystal cracking resulting from phase transitions associated with this family compounds are minimized by the hydrothermal crystal growth technique. Crystals of good optical quality with only minor amounts of metal ion reduction can be grown this way. Reactions were also designed to provide homogeneous distribution of tantalum and niobium metal centers throughout the KTN crystal lattice to maximize its electro-optic properties. Synthesis was performed at relatively low (500-660 °C) temperatures in comparison to the flux and Czochralski techniques. This work represents the largest crystals of this family of compounds grown by hydrothermal methods to date.     

Simple but efficient synthesis of novel substituted benzimidazoles over ZrO2-Al2O3

Solid-acid catalytic materials such as ZrO₂-Al₂O₃ containing 80?mol% of ZrO₂ were prepared by the solution combustion method (SCM) using different fuels such as urea, hexamethylene tetramine, glycine, and sucrose. All the prepared solid acid catalytic materials were characterized for their physico-chemical properties like crystalinity, acidity, functionality and morphology. These materials were evaluated for their catalytic activity in the synthesis of a series of novel substituted benzimidazoles. The reaction conditions were optimized by varying the solvents, reaction temperature, weight of solid acid catalyst, molar ratio of the reactants, and reaction time. The ZrO₂-Al₂O₃ solid acid catalytic material prepared by urea as a fuel was found to be highly active, recyclable, and reusable in the synthesis of benzimidazoles. A possible reaction mechanism for the synthesis of benzimidazoles is also proposed.     

One‐Pot Synthesis of Benzimidazoles from o‐Nitroanilines under Microwaves via a Reductive Cyclization

An efficient microwave irradiation synthesis of 2‐substituted benzimidazoles in one step via the Na₂S₂O₄ reduction of o‐nitroanilines in the presence of aldehydes is described. The method is simple and a good option to obtain the title compounds in a very short time.     

A two-step procedure for the preparation of mono-protected bis-N-heterocyclic alkyl ether systems

A two-step convenient sequence for the synthesis of previously inaccessible mono-Boc-protected bis-N-heterocyclic alkyl substituted ether derivatives 4 is described. Mitsunobu protocol was applied to the preparation of pyridinyl ether precursor 5. The reduction of the electron rich pyridinyl system 5 has been achieved catalytically using the combination of PtO₂-H₂SO₄ or PtO₂-pTsOH under a hydrogen atmosphere maintained by a gas balloon at ambient temperature.     

Characterization and evaluation of Fe2O3/Al2O3 oxygen carrier prepared by sol–gel combustion synthesis

The sol-gel combustion synthesis (SGCS) for oxygen carrier (OC) to be used in chemical looping combustion (CLC) was first designed and experimented in this work, which is a new method of OC synthesis by combining sol-gel technique and solution combustion synthesis. Cheap hydrated metal nitrates and urea were adopted as precursors to prepare Fe₂O₃/Al₂O₃ OC at the molar ratio to unity (Fe1Al1), which was characterized through various means, including Fourier transforms infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), differential thermal analysis (DTA), X-ray diffractor (XRD), and N₂ isothermal adsorption/desorption method. FTIR analysis on the chemical structure of the dried gel of Fe1Al1 indicated that urea was partly hydrolyzed and the hydrated basic carbonate was formed by the combination of groups such as (Fe(_1−yAl_y)_1−xO_1−3x, CO₃²⁻ and -OH-. By analyzing the staged products during SGCS, calcination was found as a necessary step to produce Fe₂O₃/Al₂O₃ OC with separate phases of α-Fe₂O₃ and α-Al₂O₃. Through TGA-DTA, the decomposition of the dried gel was found to undergo five stages. The analysis of the evolved gases from the gel decomposition using FTIR partially confirmed the staged decomposition and assisted a better understanding of the mechanism of SGCS. XRD identification further substantiated the necessity of calcination to synthesize Fe₂O₃/Al₂O₃ OC with separate phases of α-Fe₂O₃ and α-Al₂O₃, though it was not necessary for the synthesis of single phase α-Fe₂O₃ and α-Al₂O₃. Structural characterization performed on N₂ adsorption analyzer displayed that the pore shape of Fe1Al1 particles was heterogeneous. Finally, H₂ temperature-programmed reduction (TPR) of Fe1Al1 products in TGA indicated that the reduction reaction of Fe1Al1 OC after calcination was a single step reaction from α-Fe₂O₃ to Fe, and calcination benefited to improve the transfer rate of the lattice oxygen from the OC to fuel H₂. Furthermore, four times of reduction and oxidization (redox) reaction by alternating with H₂ and air demonstrated the synthesized OC had good reactivity and sintering-resistance, much suitable to be used in the realistic CLC. Overall, the SGCS method was found superior to other existent methods to prepare Fe₂O₃/Al₂O₃ OC for CLC application.