红外探测器光电性能测量系统方案研究

本文提出了一种新型的由微机控制的全自动红外探测器件光电性能测量系统,针对系统的硬件组成部分及其设计思想做了详细的讨论.     

偏振-米散射激光雷达的研制

研制的偏振-米散射激光雷达（PML）,可用于探测卷云和沙尘气溶胶的后向散射光退偏振比以及研究流层大气气溶胶的消光特性。采用窄带滤光片和光阑,将接收到的激光大气回波信号谱线（米散射和瑞利散射光谱）从天空太阳背景噪声中分离出来,以提高系统的白天探测能力。介绍了偏振-米散射激光雷达的结构、技术参数、测量方法和数据处理方法。对偏振-米散射激光雷达的性能参数进行了测定,并对测定结果进行了分析与讨论,给出了偏振-米散射激光雷达对合肥市地区(117.16°E, 31.90°N)上空大气气溶胶的消光特性和卷云的结构、退偏振比垂直廓线以及光学厚度的典型探测结果,对这些结果进行了分析和讨论。结果表明：研制的偏振-米散射激光雷达性能可靠,能对大气气溶胶和卷云的物理和光学特性进行有效的探测。     

共路径光相干成像系统光纤探头的研究

本文提出了基于楔形光纤以及端面成角度光纤的共路径光相干成像系统探头,实现背向散射信号在其端部的共路径相位干涉,从而获得待测件断面成像信息.首先,建立了共路径光相干成像系统光路及探头相位干涉的理论模型,分析了各光纤探头尺寸与干涉信号强度、系统性能的关系.其次,分别设计出楔形光纤、端面成角光纤探头,开展了共路径光路干涉实验,搭建了工作波长为1 550 nm的共路径光路测试系统.然后,根据不同待测样品的散射率,设计并研制了不同角度的楔形光纤探头,分析了不同尺寸的光纤探头对系统性能的影响,针对不同样品开展了固定探头探测实验.实验结果表明,楔形光纤端部可直接对输出光聚焦,照射在被测样品上,且其端面成一定角度时,可调节输出分光比,实现对参考信号的调节,提高了系统信噪比.为进一步开展共路径光相干成像系统的研究奠定了基础.     

微弱信号源的和波束定向方法与分裂波束定向方法的性能比较

本文讨论水下辐射噪声源的精确定向问题，给出被动声纳和波束定向与分裂波束定向方法的性能比较。指出在一定信噪比下，分裂波束精确测向技术比和波束定向技术具有较高的定向精度。但是，随着信噪比的下降，两者趋于一致。推导了估计定向精度的分析表达式，给出在直线阵和圆弧阵情况下，延时估计和声源入射角偏差之间的换算公式和数值模拟结果。同时给出数字式声纳用以计算入射信号左波束和右波束数据的互谱来实现分裂波束定向的方法。     

基于高速移动通信的虚拟天线阵列理论研究

在高速移动通信中, 多普勒频移对通信性能产生严重的影响, 通常需要对接收信号的多普勒频移进行估计并进行补偿. 本文研究在对单个天线接收的高速移动通信信号进行频移估计和补偿的基础上产生多路无频偏的信号, 并虚拟为天线阵列的输出以提高系统的接收增益. 首先讨论了“均匀时间采样”和“均匀相位采样”的关系, 并根据两者之间的关系提出了补偿多普勒频移和虚拟天线阵列的算法, 即对采样信号进行插值、均匀相位抽取以后, 再进行均匀时间采样. 然后分析了算法对高速移动通信系统性能的改善作用, 并提出了算法的硬件实现结构. 通过数值仿真验证了算法的干扰抑制能力和误码性能, 结果表明本文提出的虚拟天线阵列算法能够改善飞机、高铁上的高速移动通信系统的性能.     

双圈同轴式光纤涡轮流量计的智能化设计

为了克服现有电磁式涡轮流量计的量程小,易受电磁干扰的缺点,本文设计了一种双圈同轴式光纤的涡轮流量智能检测系统。该测试系统由三大模块组成,双圈同轴式的光纤传感器作为信号拾取工具,硬件电路对信号进行预处理,TMS320F2812 DSP对信号进一步软件处理。经过实验验证,该测试系统在5-300Hz的测量范围内,测量误差小于0.5%。因此,该测试系统具有较高的测量精度和可靠性,这为光纤涡轮流量计的样机制作提供了重要依据。     

Application of fiber interferometer in coherent Doppler lidar

A novel coherent Doppler lidar (CDL) system based on single-mode fiber (SMF) components and instruments is presented to measure the speed of target. A fiber interferometer used in CDL system is reported.This fiber mixer is employed as a coherent receiver to resolve the shifts of signal-to-noise ratio (SNR) and mixing efficiency induced by backscattered field's wavefront error. For a certain wavelength, the maximum coupling efficiency between signal and SMF is determined by the ratio of pupil diameter to focal length of the coupling lens. The legible interference patterns and spectrum signals show that fiber interferometer is suitable to compensate for amplitude and phase vibrations. This robust coherent receiver can achieve improved CDL system performance with less transmitter power.     

无线光码分多址中一种改进的盲多用户检测算法

干扰消除是无线光码分多址(CDMA)通信系统中的一项关键技术。分析了基于递归最小二乘(RLS)算法的盲多用户检测算法的原理及性能,并将其应用于采用光正交码的无线光CDMA系统中。讨论了该系统中遗忘因子的选取原则及其对算法的收敛性和系统误码率性能的影响。为了克服固定遗忘因子所带来的矛盾,提出了一种改进的变遗忘因子RLS盲多用户检测算法,并对遗忘因子进行了修正。结果表明,采用改进的方法后系统能获得较快的收敛速度和跟踪速度,收敛时的估计误差也较小,而且信号干扰比由传统算法的6dB提高到9dB。说明采用变遗忘因子的RLS算法不仅适合于采用光正交码的无线光CDMA系统,而且跟踪期望用户信号的性能良好。     

Performance of Indoor Infrared Wireless CDMA Systems with Angle Diversity

Indoor infrared communication systems is one of the possible ways of offering data rates in excess of 100 Mbit/s without the need for wiring. Multiple users can share an infrared channel by code division-multiple access (CDMA) techniques. However, the CDMA system performance is limited by both background noise and co-channel interference. In this paper we study the use of angle diversity for mitigating the effects of the noise and interference. The system considered uses on-off shift keying modulation with multibeam transmitters and imaging receivers. The overall system performance for different diversity combining techniques is evaluated and compared to a system without diversity. Numerical results for a 2-user CDMA system indicate that signal to noise and interference ratio (SNIR) improvement (over systems with no diversity) of 5 dB is obtained for at least 50% of an ensemble of 10000 sample evaluations. The generalized selection combining (GSC)--a new diversity technique yet to be implemented for infrared systems--offers the best performance even with its reduced complexity.     

基于DSP的激光陀螺稳频回路设计及其参数整定

针对某小型化激光陀螺,对基于TMS320F2810数字信号处理芯片（DSP）的激光陀螺交流抖动稳频回路设计及其参数整定进行了理论分析、Matlab数值仿真和实验研究。TMS320F2810这款芯片具有集成度高、处理速度快、功耗低和性价比高等突出优点,有利于实现激光陀螺控制系统的小型化。基于这款DSP芯片实现了某小型化激光陀螺的交流抖动稳频回路的软、硬件设计,使用衰减曲线法得到了该型激光陀螺经优化后的PID控制参数（Kp=0.048,Ki=0.059,Kd=0.013）,并根据国军标对稳频回路进行了实验验证。实验结果表明,稳频控制回路经过PID参数整定后,该小型化激光陀螺的零偏稳定性从0.025/h降到0.014/h,该稳频控制回路在目标型号激光陀螺上满足预期的性能指标要求。     

Interference fringe detection system for distance measuring interferometer

A novel photodetection system for a homodyne distance measuring interferometer by means of fringe counting method is presented. The system is based on applying compact size integrated photodetector operating with fringe pattern having fixed, finite period. 13-element integrated photodiode arranged in novel signal processing scheme receives interference fringes movement. Additional lens is used to adjust the fringe period to photoelements’ distances. Due to the proposed configuration of the photoelement's signal processing and the applied lens the system has reduced sensitivity to interference fringe period errors caused by the angular misalignment of interfering beams. The theoretical analysis and experimental verification of the system metrological feasibilities are presented. Comparison of performance of examples of standard and novel detection systems is shown finally.     

Multiple access interference rejection in OCDMA using a two-photon absorption based semiconductor device

An experimental demonstration of a two-channel OCDMA system with detection performed using standard linear detection or a TPA-based nonlinear detector is presented. These results show an improvement in the extinction ratio of the decoded signal by ∼5 dB using TPA detection. A simulation model of the TPA detector used during the experiments was created and used in a four-channel OCDMA system simulation using both linear and nonlinear detection methods. The simulation results show that error-free performance is achievable for a 4-user system using the nonlinear TPA detector while the OCDMA system employing linear detection is severely limited by the effects of noise generated by adjacent optical channels (multiple access interference).     

A one-dimension convolutional neural network based interference classification method

Interference is a common problem in wireless communication, navigation and radar systems. A wide variety of interferences are used to degrade the communication quality especially in electronic warfare environment. In modern military communication systems, interference classification is an important module for its ability to obtain prior interference information before adopting related anti-interference method. This paper proposes a deep learning based interference classification method, which applies one-dimension convolutional neural networks to automatically extract interference features for classification. Computer simulations show better classification performance and lower computational complexity. Meanwhile, this proposed method is implied on software defined radios (SDR) hardware, more than 99% correct classification probability can be achieved with limited samples of the received signal, which verifies the robustness of this proposed method.     

磁共振成像信号的数字化接收系统设计

磁共振成像信号的采集是磁共振成像系统当中最重要的环节之一,设计性能良好的信号接收系统直接关系到成像质量的好坏. 本文根据磁共振信号强度弱、频率高、带宽窄的特性对接收系统进行了统一设计. 详细地对可控增益放大、高速A/D、数字解调以及抽样滤波器等几个部分进行了讨论,给出一整套设计方案,尤其对多级抽样滤波器,根据磁共振成像的性能需求和滤波器的不同特性给出了抽样系数分配和滤波器设计的一般方法. 根据该方案设计出的磁共振信号接收系统有较高的信噪比,已经应用在临床医疗诊断当中.      

An adaptive smooth unsaturated bistable stochastic resonance system and its application in rolling bearing fault diagnosis

An adaptive smooth unsaturated bistable stochastic resonance (ASUBSR) system for bearing fault signal detection is established. Based on the problem of output saturation and poor low-frequency suppression performance of classical bistable stochastic resonance (CBSR) system, an SUBSR with unsaturated characteristics is proposed. An ASUBSR system is designed by extracting the envelope spectrum of the input signal and resampling it to satisfy the adiabatic approximation condition, combining high-pass filter to filter out low-frequency interference, and using genetic algorithm to select the optimal system parameters. Through simulations and experiments, we found that the system can effectively suppress the interference of low-frequency and high-frequency, indicates that the system performs like a band-pass filter, and the output signal-to-noise ratio is better than that of the CBSR system. The proposed ASUBSR system has great application in the field of fault detection of rolling bearings.     

动态干涉条纹相位提取的抗干扰算法

为减小在动态干涉条纹的相位提取中噪声带来的计数误差,研究了在希尔伯特变换相位提取的基础上,利用反正切相位跳变特性,通过软件实现可逆计数的抗干扰算法。通过模拟实验对算法的抗干扰性能进行了验证,实验结果表明：所提出的相位提取算法具有较强的抗干扰性能,在信噪比为11时,算法仍然能得到正确的结果。     

Noise Immunity of the Compression Procedure for a Narrow-Band Signal

We consider the noise immunity of the compression procedure for a narrow-band signal [1]. The noise immunity is understood as the ratio of the maximum amplitude of the compressed signal to the noise intensity. It is shown that in the case where a narrow-band signal is compressed, this ratio increases if noise is a reverberation interference, remains unchanged if noise is fed to the wide-band input channel of a radar, and decreases if the radar input channel is narrow-band. Results of the calculations and numerical simulations are presented.     

斩波式自适应移相干涉技术

研究对环境振动和空气扰动所造成的两相干光束间常数项光程变化不敏感的自适应移相干涉系统，利用偏振分光技术，采用闭环控制，并将高频振幅调制与锁相技术相结合，建立一斩波式自适应移相干涉系统，可对环境振动引起的干涉条纹的抖动进行实时探测并予以光程补偿，将干涉条纹依次锁定在与任意相位差相对应的位置,该方法不受两相干光束间光程差大小的限制且具有高信噪比，阐述了该方法的原理，描述了所建立的系统，并给出了实验结果。     

Optimum beamformer in correlated source environments

A new method for overcoming signal cancellation problems due to correlated interferences which occur in a minimum variance distortionless response beamformer is proposed. Instead of decorrelating the correlated interferences, the coherently combining signal-to-interference plus noise ratio (CC-SINR) beamformer regards them as replicas of the desired signal and coherently combines them with the desired signal. This method uses an eigenvector constraint that suppresses only noise and uncorrelated interferences but retains the desired signal and correlated interferences. The CC-SINR beamformer does not require any preliminary information on correlated interferences. The signal-to-interference plus noise ratio (SINR) of the proposed beamformer output was compared to that of a conventional SINR beamformer when correlated interference, uncorrelated interference, and white noise exist. In addition, various key parameters that affect the performance of the beamformer, such as signal-to-noise ratio, uncorrelated interference-to-noise ratio, angular separation between signals, attenuation factor, phase delay of correlated interference, and the number of sensors were analyzed. All of the experimental results were in good agreement with the analytical results.     

Performance analysis of a swept-source optical coherence tomography system with a quadrature interferometer and optical amplification

A performance analysis of signal to noise ratio for an optical coherence tomography system with quadrature detection and a semiconductor optical amplifier in the sample arm is discussed. The results are compared and discussed in relation to a conventional OCT system (without optical amplification). An increase of the signal to noise ratio up to 14 dB at a depth of 0.5 mm is obtained compared to the system without the optical amplifier. Overall, an improvement was demonstrated for signal coming from deeper regions within the samples. Arterial plaque from a myocardial infarction-prone Watanabe heritable hyperlipidemic (WHHLMI) rabbit is visualized and characterized using this system. Improvement of signal to noise ratio increases the penetration depth possible for OCT images, from 1 mm to 2 mm within the vessel wall of an artery. Preliminary results show that vulnerable plaque with fibrous cap, macrophage accumulations and calcification in the arterial tissue are measurable with this OCT system.