碳纳米管网/聚苯胺复合材料的制备及电化学储能性能

分别采用粉末碳纳米管(CNT)和带连接点的碳纳米管网(CNTN)为模板,通过与聚苯胺(PANI)有限域聚合得到了CNT/PANI和CNTN/PANI 2种复合材料.采用透射电子显微镜和扫描电子显微镜对材料的形貌进行了表征,采用氮气吸附-脱附分析研究了材料的孔结构参数,运用双电四探针测试仪对材料的导电性能进行了测试,利用恒流充放电、循环伏安、循环寿命及交流阻抗等电化学测试手段表征了材料的电化学储能性能.结果表明,CNTN/PANI复合材料比CNT/PANI复合材料表现出更好的导电性能和电化学储能性能,其放电比容量可达到143.2 F/g(有机电解液).     

MnO2/PPy/PANI三元纳米管复合材料的合成及其电化学电容性能

在聚苯胺（PANI）和二氧化锰（MnO2）存在的条件下,以FeCl3/甲基橙为模板,通过化学氧化法聚合吡咯(Py)单体,制备MnO2/PPy/PANI纳米管复合材料。 利用X射线衍射、透射电子显微镜、红外光谱和电化学测试等多种测试技术对复合材料进行物性表征和电化学电容性能测试,并讨论了不同含量的PANI对复合物材料的结构和性能的影响。 结果表明,由于PANI、MnO2与PPy三者的相互协同作用,以及材料管状结构的大比表面积,使三元复合材料具有比二元复合材料要大的电化学活性。 所合成的三元复合材料最大比容量达到458.4 F/g。     

纳米BaFe12O19纤维的电纺制备及磁性研究

以PVP的乙酸溶液为助纺剂,采用静电纺丝技术制得了纳米BaFe12O19纤维,利用XRD和EDS对样品的物相和成分进行了分析,利用SEM和TEM对样品形貌和粒径进行了表征,并利用振动样品磁强计(VSM)对样品进行了磁性能研究.结果表明,BaFe12O19/PVP复合纤维经过800℃煅烧后,制得了纯净的BaFe12O19纳米纤维,纤维平均直径为150 nm,呈现出多晶结构,矫顽力为4 164.9 G,与粉体相比,矫顽力有较大提升,有望扩展BaFe12O19在高密度垂直记录材料、微纳米电子材料和微波材料等领域的应用.     

有机化学接枝-电化学沉积聚合制备CNTs/PANI纳米复合材料

通过有机化学合成法先在碳纳米管表面接枝上苯胺单体,然后在不锈钢电极表面在硫酸溶液中采用循环伏安法电化学沉积聚合制得碳纳米管/聚苯胺(CNTs/PANI)纳米复合材料.扫描电子显微镜和傅立叶变换红外光谱表征所得材料的微观结构和基团,循环伏安和恒流充放电测试用于考察所得CNTs/PANI纳米复合材料的电化学性能.所得结果与...     

不同质子酸掺杂对银/聚苯胺纳米复合材料结构和导电性的影响

利用紫外光作为辅助条件,在反胶束体系中采用一步双原位法合成了硝酸(HNO3)、对甲基苯磺酸(TSA)和5-磺基水杨酸(SSA)掺杂的银/聚苯胺(Ag/PANI)纳米复合材料.通过对复合材料进行红外光谱(FTIR)、紫外光谱(UV-Vis)、扫描电镜(SEM)、X射线衍射(XRD)和导电性能的测试,研究了不同质子酸对Ag/PANI纳米复合材料结构、形貌和导电性能的影响.测试结果表明,3种酸掺杂制备的Ag/PANI纳米复合材料均为聚苯胺包覆银粒子的核-壳结构.不同的质子酸掺杂会对Ag/PANI纳米复合材料的电性能有重要影响.在3种酸掺杂的复合材料中,TSA掺杂的复合材料的电导率最佳,为215.14 S·cm-1.     

杂多酸/聚苯胺/二氧化锰复合材料的制备及其电化学性能研究

使用磷钨酸(PW₁₂)为苯胺(AN)单体聚合提供酸环境,合成聚苯胺(PANI),通过原位聚合法制备出不同比例的PW₁₂/PANI/MnO₂复合材料。通过红外光谱(FT-IR)、X射线衍射(XRD)和扫描电镜(SEM)对复合材料电极材料的结构和形貌进行表征,利用电化学工作站测试复合材料的电化学性能。结果表明,制备出的复合材料呈现以下优点,例如明显的多孔结构,较大的比表面积,材料的团聚现象也得到了明显的改善,复合材料的比电容达到493.29 F/g左右,说明经过掺杂的复合材料的电化学性能相对于单一赝电容材料(聚苯胺,314.27 F/g)有了明显的提升,合成的三元纳米复合材料具有作为电极材料的潜力,可用于下一代高速率储能系统。     

聚苯胺/H2W2O7层状复合材料的制备研究

以层状钨基氧化物(H2W2O7)为无机主体, 用正庚胺改性后的正庚胺/H2W2O7复合物(HTT)为中间体, 通过离子交换、层间O2引发聚合等步骤成功制备了聚苯胺/H2W2O7层状复合材料(PANI/H2W2O7). X射线衍射、扫描电子显微镜、红外光谱及差热分析结果表明: 聚苯胺分子已成功地嵌入H2W2O7层间, 层状结构没被破坏, 层间距变至1.19 nm; 聚苯胺的嵌入还大大提高了材料的热稳定性. 讨论了无机主体与有机客体之间的相互作用、聚苯胺在层间的排布形式及苯胺和聚苯胺插入层间的反应机理.     

微米聚苯胺/Fe_3O_4空心球的制备及吸波性能

采用界面聚合和Pickering乳液聚合相结合的方法,以甲苯为软模板,磁性Fe3O4纳米颗粒为稳定剂,十二烷基苯磺酸钠(SDBS)为乳化剂,过硫酸铵(APS)为氧化剂,盐酸(HCl)为掺杂剂,制备了掺杂态聚苯胺/Fe3O4(D-PANI/Fe3O4)空心球.作为比较,在不掺杂盐酸的条件下,制备了本征态聚苯胺/Fe3O4(PANI/Fe3O4)空心球.用透射电子显微镜(TEM)、扫描电子显微镜(SEM)、X射线衍射(XRD)仪、傅里叶变换红外光谱(FTIR)仪、热重分析(TG)仪、振动样品磁强(VSM)计及恒压四探针测试仪对复合材料的形貌、结构、组成和电磁性能进行了表征.结果表明,D-PANI/Fe3O4空心球的直径约为2.8μm,电导率和饱和磁化强度(Ms)分别为2.75×10-2S/cm和54.26 A·m2/kg.用矢量网络分析(VNA)仪对D-PANI/Fe3O4空心球和PANI/Fe3O4空心球吸波性能进行分析,结果表明,D-PANI/Fe3O4空心球在12.64 GHz处的最小反射率为-43.3 d B,对应的匹配厚度为2 mm,其吸波性能明显优于PANI/Fe3O4空心球.     

还原氧化石墨烯表面聚苯胺纳米阵列的制备及电化学电容性能

本文以阳极氧化铝(AAO)膜为模板,通过恒电位法在自组装还原氧化石墨烯(rGO)膜表面制备有序聚苯胺(PANI)纳米线阵列。通过拉曼光谱和场发射扫描电子显微镜分别对其结构和微观形貌进行了表征,并对PANI纳米线阵列的电化学电容性能进行了测试。结果表明,rGO膜表面可电沉积PANI,电沉积得到的PANI纳米线阵列具有比PANI薄膜材料更高的电容和比电容。     

Fe_3O_4@聚吡咯@聚苯胺核壳结构的制备及吸波性能

用聚吡咯(PPy)对溶剂热法制备的Fe_3O_4纳米颗粒进行表面修饰,再用聚苯胺(PANI)调控Fe_3O_4@PPy复合材料的电磁组成,制备出具有核壳结构的Fe_3O_4@PPy@PANI复合吸波材料.当PPy对Fe_3O_4纳米颗粒修饰后,PANI极易包覆在纳米颗粒表面.电磁性能分析结果表明,当苯胺(An)与Fe_3O_4@PPy质量比为1/4时,最小反射损耗值(RLmin)达到-39.2 d B;当An与Fe_3O_4@PPy的质量比为1/2时,反射损耗小于-10d B的频宽达到4.6 GHz.电磁成分比例对复合材料的吸波性能有较大的影响,随着聚苯胺含量的增加,电磁吸收呈现先增加后减小的趋势.     

Preparation, Characterization and Magnetic Properties of PANI/La-substituted LiNi Ferrite Nanocomposites

Magnetic nanocomposites containing polyaniline （PANI）-coated La-substituted LiNi ferrite （LiNi0.5La0.02Fe1.98O4） were synthesized by in situ polymerization in aqueous solution of hydrochloric acid. The nanocomposites exhibited the magnetic hysteresis nature under applied magnetic field. The saturation magnetization （Ms） and coercivity （Hc） varied with the ferrite content. The obtained nanocomposites were characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM）, scanning electron microscopy （SEM）, Fourier transform infrared spectroscopy （FT-IR）, UV-Visible spectroscopy and vibrating sample magnetometer （VSM）. TEM and SEM studies showed that the nanocomposites present the core-shell structure. The results of XRD patterns, FT-IR and UV-Visible spectra indicated the formation of PANI-LiNi0.5La0.002Fe1.98O4 nanocomposites and showed that the interaction existed between PANI backbone and ferrite particles in the nanocomposites. The bonding mechanism in the nanocomposites has been proposed.     

Synthesis and Electro-magnetic Properties of Polyaniline-barium Ferrite Nanocomposite

"The polyaniline (PANI)-barium ferrite composite with magnetic behavior was synthesized by in situ poly-merization of aniline in the presence of BaFe12O19 nanoparticles of 60-80 nm in diameters. The structure, morphology and magnetic properties of samples were characterized by powder X-ray diffraction, Fourier transform infrared, scanning electron microscopy, transmission electron microscopy and vibrating sample magnetometer technique. The results of spectroanalysis indicated that there was interaction between PANIchains and ferrite particles. The composite exhibited the hysteresis loops of the ferromagnetic nature. The saturated magnetization of composite was 22.2 emu/g and the conductance was 0.069 S/cm."     

Preparation and magnetic properties of Zn-Cu-Cr-La ferrite and its nanocomposites with polyaniline

Nanosized Zn(0.6)Cu(0.4)Cr(0.5)Fe(1.5-x)La(x)O(4) (x=0 - 0.06) ferrites doped with La are synthesized by a rheological phase reaction method. Polyaniline (PANI)/ferrite nanocomposites are prepared by in situ polymerization method. The structure, morphology and ferromagnetic property of ferrite powders and nanocomposites are characterized by X-ray powder diffractometer (XRD), transmission electron microscope (TEM), Fourier transform infrared spectra (FTIR), UV-visible spectroscopy (UV), thermogravimetric analysis (TGA) and vibrating sample magnetometer (VSM). The results indicate that the PANI and nanosized ferrite powders can be combined effectively. The polymers can reduce the agglomeration of nanosized ferrite particles to some extent, which is good for the dispersedness and stabilization of nanoparticles. The PANI/ferrite nanocomposites under applied magnetic field exhibit the hysteretic loops of the ferromagnetic nature. The magnetic properties of nanocomposites are tailored by controlling the ferrite content.     

Constructing magnetic polyaniline/metal hybrid nanostructures using polyaniline/Fe3O4 composite hollow spheres as supports

Polyaniline (PANI)/Fe₃O₄ composite hollow spheres have been successfully synthesized in one step using sulfonated polystyrene (PS) spheres as templates. The magnetic PANI hollow spheres were used as supports for noble metal nanoparticles (NPs) such as Au and Pd. The morphology, composition and magnetic properties of the resulting products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, inductively coupled plasma (ICP) atomic spectra and vibrating sample magnetometer. The catalytic activity of magnetic PANI/Au composite shells on the oxidation of dopamine was investigated by cyclic voltammetry. The obtained results provide our product with a practical application for the detection of dopamine. On the other hand, the catalytic activity of magnetic PANI/Pd composite shells on the reduction of 4-nitroaniline was investigated by spectroscopic methods and compared with Pd/C catalyst which was already widely used in industrial production.     

单分散P(St-BA-AN)/PANI核壳结构复合微球的制备与电性能

以苯乙烯(St)、丙烯酸丁酯(BA)和丙烯腈(AN)为单体, 采用乳液聚合的方法制备出单分散苯乙烯-丙烯酸丁酯-丙烯腈三元共聚物[P(St-BA-AN)]种子微球, 再在该种子微球表面包覆聚苯胺(PANI), 制得P(St-BA-AN)/PANI核壳结构复合微球. 采用扫描电镜(SEM)、透射电镜(TEM)、傅里叶变换红外透射光谱(FTIR)和漫反射光谱等测试手段对所制备的种子微球和复合微球的形态、结构和形成机理进行了研究, 并用四探针法测定了核壳结构复合物的导电性. 研究结果表明, 通过改变种子乳液共聚物的组成和加入苯胺的量及氧化剂的量等条件可调控复合微球的电导率. 与P(St-BA)/PANI核壳结构复合微球相比, 在核组成中引入了氰基的P(St-BA-AN)/PANI核壳结构复合微球的电导率明显提高, 当加入苯胺的量为P(St-BA-AN)种子微球与苯胺单体总质量分数的40%时, 其电导率可达到0.71 S/cm. 红外光谱结果证实了P(St-BA-AN)种子微球中的氰基和壳层中聚苯胺的胺基之间存在某种相互作用, 导致核壳结构复合物电导率的提高.     

超疏水聚苯胺/聚四氟乙烯复合膜的制备及油-水乳液分离性能

以苯胺为原料, 采用原位聚合法在聚四氟乙烯(PTFE)基体上合成聚苯胺/聚四氟乙烯(PANI/PTFE)复合膜. 利用光学显微镜、 扫描电子显微镜(SEM)、 傅里叶变换红外光谱(FTIR)、 紫外-可见吸收光谱(UV-Vis)和静态水接触角测试对PANI/PTFE复合膜的形貌、 结构和浸润性进行分析, 并对其油包水乳液分离性能、 通量和循环使用性能进行了测试. 研究结果表明, PANI/PTFE复合膜仅在重力条件就能有效分离油包水乳液; 而且重复数十次过滤后, PANI/PTFE复合膜仍具有良好的抗污能力和分离性能.     

Well-dispersed multi-walled carbon nanotube/polyaniline composite films

Multi-walled carbon nanotube (MWNT)/polyaniline (PANI) composite films with good uniformity and dispersion were prepared by electrochemical polymerization of aniline containing well-dispersed MWNTs. The results of transmission electron microscopy (TEM) show that aniline can be used to solve MWNTs via formation of donor–acceptor complexes. Scanning electron microscopy (SEM), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) revealed that the well arrangement of PANI-coated MWNTs in these films facilitated improved electron and ion transfer relative to pure PANI films and this may be due to the strong interaction between MWNTs and PANI.     

The Electrochemical Properties of Nanocomposite Films Obtained by Chemical In Situ Polymerization of Aniline and Carbon Nanostructures

Interactions between the π bonds in the aromatic rings of polyaniline (PANI) with carbon nanostructures (CNs) facilitate charge transfer between the two components. Different types of phenyleneamine‐terminated CNs, including carbon nano‐onions (CNOs) and single‐walled and multi‐walled carbon nanotubes (SWNTs and MWNTs, respectively), were prepared as templates, and the CN/PANI nanocomposites were easily prepared with uniform core–shell structures. By varying the ratio of the aniline monomers relative to the CNs in the in situ chemical polymerization process, the thickness of the PANI layers was effectively controlled. The morphological and electrical properties of the nanocomposite were determined and compared. The thickness and structure of the PANI films on the CNs were characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), and infrared spectroscopy. TEM and SEM revealed that the composite films consisted of nanoporous networks of CNs coated with polymeric aniline. The electrochemical properties of the composites were investigated by cyclic voltammetry and electrochemical impedance spectroscopy. These studies showed that the CN/PANI composite films had lower resistance than pure polymeric films of PANI, and the presence of CNs much improved the mechanical stability. The specific electrochemical capacitance of the CNO/PANI composite films was significantly larger than for pure PANI.     

Synthesis of polyaniline/Q-CdSe composite via ultrasonically assisted dynamic inverse emulsion polymerization

In this communication, polyaniline/CdSe quantum dots (PANI/Q-CdSe) composite was successfully synthesized via in situ ultrasonically assisted dynamic inverse emulsion polymerization. The synthesized PANI-coated Q-CdSe composite was characterized by field emission transmission electron microscopy showed that the CdSe quantum dots have an average size of around ca. 5 nm were dispersed in the PANI matrix. X-ray diffraction, Fourier transform infrared spectrum (FT-IR) and UV-visible spectrum were used to characterize the structure of the obtained PANI/Q-CdSe composite. FT-IR spectra indicated that the polymer was highly doped and existed in conducting emeraldine salt form. The obtained PANI/Q-CdSe composite showed significant improvement in the thermal behavior as indicated by TGA thermograph. The presented dynamic polymerization process is very fast and produces stable colloidal dispersion. This approach provides a one-step, simple, general, and inexpensive method for the preparation of PANI/Q-CdSe composite.     

碳纳米管/聚苯胺/石墨烯复合纳米碳纸及其电化学电容行为

通过真空抽滤的方法制备碳纳米管纸,并对其进行循环伏安电化学氧化处理.以该电化学氧化处理的碳纳米管(CV-CNT)纸为基体,采用电化学聚合沉积聚苯胺(PANI),随后吸附石墨烯(GR),制备具有三明治夹心结构的碳纳米管/聚苯胺/石墨烯(CV-CNT/PANI/GR)复合纳米碳纸.该结构外层为GR,内层由PANI包裹的CNT形成网络骨架,充分发挥三者各自优势构建柔性电极材料.用场发射扫描电镜(FE-SEM)、透射电子显微镜(TEM)、拉曼光谱对其形貌与结构进行表征,并测试其电化学性能.研究发现:PANI呈纳米晶须状,并均匀包裹在CV-CNT表面;该复合碳纸具有良好的电容特性、大电流充放电特性以及良好的循环稳定性能.电流密度为0.5A·g-1时,比电容可达415F·g-1;20A·g-1时仍能保持106F·g-1的比电容.由于GR的保护作用,1000次循环之后较CV-CNT/PANI保持更高的有效比电容.该CV-CNT/PANI/GR复合碳纸展现出在高性能超级电容器柔性电极材料的潜在应用价值.