以电化学方法在离子液体[DEME][BF4]中合成铂纳米粒子

通过恒电位电沉积法在离子液体N,N-二乙基-N-甲基-N-（2-甲氧基乙基）铵四氟硼酸铵（[DEME][BF₄]）中,在玻碳电极上制备了铂纳米颗粒。首先探究了不同沉积电势和不同沉积时间对铂纳米粒子微观形貌的影响,由SEM和TEM图发现在-2.5 V下沉积480 s制备的铂纳米粒子的平均粒径约为2.38 nm。使用高分辨率透射电子显微镜（HRTEM）和电子衍射（SAED）对其晶体结构进行表征,证明了铂纳米粒子为面心立方（fcc）晶体结构。在硫酸中测试铂纳米粒子的催化性能,发现其暴露出明显的（110）和（100）晶面。进一步对铂的电沉积行为进行研究发现,Pt （Ⅳ）的两步还原是由扩散过程和电化学过程共同控制。     

以电化学方法在离子液体[DEME][BF_4]中合成铂纳米粒子（英文）

通过恒电位电沉积法在离子液体N,N-二乙基-N-甲基-N-(2-甲氧基乙基)铵四氟硼酸铵([DEME][BF4])中,在玻碳电极上制备了铂纳米颗粒。首先探究了不同沉积电势和不同沉积时间对铂纳米粒子微观形貌的影响,由SEM和TEM图发现在-2.5 V下沉积480 s制备的铂纳米粒子的平均粒径约为2.38 nm。使用高分辨率透射电子显微镜(HRTEM)和电子衍射(SAED)对其晶体结构进行表征,证明了铂纳米粒子为面心立方(fcc)晶体结构。在硫酸中测试铂纳米粒子的催化性能,发现其暴露出明显的(110)和(100)晶面。进一步对铂的电沉积行为进行研究发现,PtⅣ的两步还原是由扩散过程和电化学过程共同控制。     

酸性离子液体中铂纳米粒子的制备、表征及应用

基于功能化离子液体的特性,开发出不使用聚合物保护剂制备铂纳米粒子并同时获得具有金属和酸活性中心双功能催化剂的新方法。首先,设计并合成出了一种新型季铵型质子(Br?nsted)酸性离子液体(N, N, N-三甲基-N-磺丁基硫酸氢铵([HSO₃-b-N(CH₃)₃]HSO₄)),然后,利用化学还原方法在该离子液体中制备了金属铂纳米粒子,并采用紫外光谱、傅立叶红外光谱、X-光电子能谱、透射电子显微镜和X射线衍射等方法对所制备的金属铂纳米粒子进行了结构表征。结果表明,所制备的铂纳米粒子具有面心立方结构,离子液体作为修饰剂修饰在铂纳米粒子的表面,有效地阻止了铂纳米粒子的团聚;将该含有铂纳米粒子的酸性离子液体作为双功能催化剂,直接用于硝基苯加氢合成对氨基苯酚反应,发现其具有良好的催化性能,在85 ℃、4 h、0.4 MPa条件下,硝基苯转化率为98.6%,对氨基苯酚收率为75.8%,回收的酸性离子液体纳米铂双功能催化体系中铂纳米粒子依然具有很好的分散性和稳定性。     

含季铵盐的芳酰腙配体的铜(Ⅱ)配合物的合成和表征:体外DNA键合和核酸酶活性

制备了2个新的含有N,N,N-三甲基丙烷-1-铵基团和N,N,N-三甲基戊烷-1-铵基团的苯乙酮-（4-羟基苯腙）配体：（E）-3-（4-（1-（2-（4-hydroxybenzoyl）hydrazono）ethyl）phenoxy）-N,N,N-trimethylpropan-1-ammonium perchlorate（H₂L¹）和（E）-3-（4-（1-（2-（4-hy-droxybenzoyl）hydrazono）ethyl）phenoxy）-N,N,N-trimethylpentane-1-ammonium perchlorate（H₂L²）。以这2个配体分别合成了2个新的铜配合物：[Cu（HL¹）₂]和[Cu（HL²）₂],研究了这些配体和配合物的DNA结合和切割活性,还研究了DNA切割的机理以及化合物浓度对DNA切割反应的影响。紫外-可见光谱结果表明,所有化合物均优先通过主沟结合模式与DNA结合,在甲基绿（主要的沟结合剂）的存在下切割DNA的活性受到抑制的结果也支持这一结论。电泳研究的结果则表明,化合物在存在或不存在氧化剂（H₂O₂）的情况下均对质粒DNA表现出显著的切割活性,活性主要取决于化合物的浓度。化合物通过水解途径裂解pBR322DNA,在存在不同自由基清除剂情况下的DNA裂解实验也支持这一结论。     

Fe-Co-Ni合金纳米粒子镶嵌的碳纳米纤维的简单制备及其吸波性能

通过在氩气中碳化含有乙酰丙酮金属盐的电纺聚丙烯腈纳米纤维合成了镶嵌（Fe_1-xCo_x）_0.8Ni_0.2（x=0.25,0.50,0.75）合金纳米粒子的碳纳米纤维,用X射线衍射（XRD）、扫描电镜（SEM）、透射电镜（TEM）、振动样品磁强计（VSM）和矢量网络分析仪（VNA）等对其物相、形貌、微观结构、静磁及电磁特性进行表征和分析,并根据传输线理论模拟计算了2~18 GHz频率范围内的微波吸收性能。结果表明：所制备的复合纳米纤维具有典型的铁磁特征,由无定形碳、石墨和面心立方结构Fe-Co-Ni合金三相组成,原位形成的合金纳米粒子沿纤维轴向均匀分布,且被有序石墨层所包覆。磁损耗和介电损耗间的协同作用及特殊的核/壳微观结构使仅含5%（w/w）的（Fe_1-xCo_x）_0.8Ni_0.2/C复合纳米纤维的硅胶基吸波涂层表现出优异的微波吸收性能。当涂层厚度为1.1~5.0 mm时,x=0.25、0.50和0.75的样品最小反射损耗分别达到-78.5、-80.2和-63.4 dB,反射损耗在-20 dB以下的吸收带宽分别为14.9、14.8和14.5 GHz,几乎覆盖整个S波段至Ku波段。通过调节合金的组成可对材料的电磁特性及微波吸收性能进行一定程度的控制。     

1-β-D-呋喃核糖基-1,2,4-三唑-3-酰胺铂配合物的合成研究

cis-[Pt(DMSO)₂Cl₂], K[Pt(DMSO)Cl₃]分别与两摩尔1-β-D-呋喃核糖基-1,2,4-三唑-3-酰胺(Ribavirin)进行络合反应, 制得了高收率的二配位铂配合物; 讨论了不同摩尔的1-β-D-呋喃核糖基-1,2,4-三唑-3-酰胺与cis-[Pt(DMSO)₂Cl₂]和K[Pt(DMSO)Cl₃]进行络合反应的结果; 对[Pt (N⁴,N⁷-Ribavirin)(DMSO)Cl]配合物(1)的X衍射晶体结构进行了测定.     

Ru纳米团簇/MoO3-x纳米带双功能催化剂的合成及其肼辅助全解水性能

将超小Ru纳米团簇锚定于富含氧空位MoO_3-x纳米带的双功能催化剂（Ru/MoO_3-x）。该催化剂展现出优异的肼氧化（HzOR）和析氢反应（HER）催化性能,10 mA·cm^-2时的过电势分别为-79和-27 mV,所组成的肼辅助电催化全解水（OWS）的电解池电压仅为13 mV,明显优于商业化20% Pt/C和已报道的一些催化剂。如此优异的性能主要归因于Ru纳米团簇有利于HzOR中N₂H₄的脱氢和HER氢中间体的吸/脱附平衡以及MoO_3-x中的氧空位和Ru/MoO_3-x异质结构导致的丰富的电化学活性位点和优化的电子转移动力学。     

受限几何型金属化合物的合成和催化性能

通过筛选合成路线和方法制备了3种桥联芴基-芳胺基化合物Me₂Si[（Flu）H]NH-2,6-ⁱPr₂C₆H₃（L¹）、Me₂Si[2,7-^tBu₂Flu（H）]NH-2,6-ⁱPr₂C₆H₃（L²）和Me₂Si[2,7-^tBu₂Flu（H）]NH-2,4,6-Me₃C₆H₂）（L³）,分别与第四族金属氯化物MCl₄反应制备了4种受限几何结构的茂金属化合物[Me₂Si（Flu）（N-2,6-ⁱPr₂C₆H₃）]ZrCl₂（THF）₂（1）、[Me₂Si（2,7-^tBu₂Flu）（N-2,6-ⁱPr₂C₆H₃）]TiMe₂（2）、[Me₂Si（2,7-^tBu₂Flu）（N-2,4,6-Me₃C₆H₂）]TiMe₂（3）和[Me₂Si（2,7-^tBu₂Flu）（N-2,6-ⁱPr₂C₆H₃）]HfMe₂（4）。化合物L¹~L³和1~4都经过谱学和元素分析表征,其中1~3还经过X射线衍射单晶结构确认。在AlⁱBu₃和（Ph₃C）⁺[B（C₆F₅）₄]-双助剂作用下研究了1~4分别催化乙烯/1-辛烯聚合性能,结果显示茂金属单活性中心作用特点以及1-辛烯的共聚效果。考察和比较了其它3种受限几何钛化合物[Me₂Si（C₅Me₄）（N^tBu）]TiCl₂、[Me₂Si（Ind）（N^tBu）]TiCl₂和[Me₂Si（Flu）（N^tBu）]TiMe₂的催化性能;讨论了1~4的结构和催化作用的关联性。     

两个含有叠氮根和硫氰根配位单元的3,4-双咪唑噻吩锰(Ⅱ)配位聚合物的合成与晶体结构

制备了2个含有叠氮根和硫氰根配位单元的3,4-双咪唑噻吩（L）的锰（Ⅱ）配位聚合物[Mn（L）（N₃）₂（H₂O）]_n（1）和[Mn（L）₂（SCN₃）₂]_n（2）并报道了它们的晶体结构。化合物1和2是通过3,4-双咪唑噻吩与四水醋酸锰反应,同时分别引入过量的线性三原子阴离子（N₃^-和SCN^-）以取代醋酸根作为抗衡离子制备而得。单晶结构分析表明1和2具有相同的无限二维链状空间结构,但是由不同的44元的[Mn₆（L）₄（2N₃）₂]和36元的[Mn₄L₄]大环单元结构组成。此外,配位聚合物1中的叠氮根分别采用端基单齿和桥联双齿的配位方式,而配位聚合物2中的硫氰根仅以端基氮原子与Mn（Ⅱ）离子配位。     

N-(1-亚氨基乙基)乙脒铂配合物合成、结构和性质

四氯合铂酸钾分别与邻、间、对磺基苯甲酸在乙腈和水中利用水热合成获得了3个铂的N-(1-亚氨基乙基)乙脒配合物:[Pt(NIA)₂]·(2-sb)·2H₂O(1),[Pt(NIA)₂]·(3-sb)·3H₂O(2)和[Pt(NIA)₂]·(1,4-dsb)·2H₂O(3)(NIA=N-(1-亚氨基乙基)乙脒,2-sb^2-=2-磺基苯甲酸二价阴离子、3-sb^2-=3-磺基苯甲酸二价阴离子、1,4-dsb^2-=1,4-二磺基苯二价阴离子)。合成过程中发生了乙氰三聚以及4-sb^2-转变为1,4-dsb^2-的反应。对配合物进行了元素分析、红外、紫外、荧光、热重和粉末X射线衍射表征,并利用单晶X射线衍射测定了配合物的晶体结构。3个配合物为阳离子-阴离子物种,阳离子为[Pt(NIA)₂]²⁺,中心金属离子四配位平面构型;阴离子与阳离子、水形成氢键,组成一个三维网络结构,但3个配合物的氢键模式不同。配合物在热稳定性、荧光性质上有一定差异。     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.