Fluid‐structure coupling of linear elastic model with compressible flow models

Cavitation erosion is caused in solids exposed to strong pressure waves developing in an adjacent fluid field. The knowledge of the transient distribution of stresses in the solid is important to understand the cause of damaging by comparisons with breaking points of the material. The modeling of this problem requires the coupling of the models for the fluid and the solid. For this purpose, we use a strategy based on the solution of coupled Riemann problems that has been originally developed for the coupling of 2 fluids. This concept is exemplified for the coupling of a linear elastic structure with an ideal gas. The coupling procedure relies on the solution of a nonlinear equation. Existence and uniqueness of the solution is proven. The coupling conditions are validated by means of quasi‐1D problems for which an explicit solution can be determined. For a more realistic scenario, a 2D application is considered where in a compressible single fluid, a hot gas bubble at low pressure collapses in a cold gas at high pressure near an adjacent structure.     

The visible and ultraviolet organic light-emitting diodes with germanium dioxide as facile solution-processed anode buffer layer

Germanium dioxide (GeO₂) aqueous solutions are facilely prepared and the corresponding anode buffer layers (ABLs) with solution process are demonstrated. Atomic force microscopy, X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy measurements show that solution-processed GeO₂ behaves superior film morphology and enhanced work function. Using GeO₂ as ABL of organic light-emitting diodes (OLEDs), the visible device with tris(8-hydroxy-quinolinato)aluminium as emitter gives maximum luminous efficiency of 6.5 cd/A and power efficiency of 3.5 lm/W, the ultraviolet device with 3-(4-biphenyl)-4-phenyl-5-tert-butylphenyl-1,2,4-triazole as emitter exhibits short-wavelength emission with peak of 376 nm, full-width at half-maximum of 42 nm, maximum radiance of 3.36 mW/cm² and external quantum efficiency of 1.5%. The performances are almost comparable to the counterparts with poly (3,4-ethylenedioxythiophene):poly (styrenesulfonate) as ABL. The current, impedance, phase and capacitance as a function of voltage characteristics elucidate that the GeO₂ ABL formed from appropriate concentration of GeO₂ aqueous solution favors hole injection enhancement and accordingly promoting device performance.     

基于光纤环的光缓存器

提出了一种基于光纤环的光缓存器的结构,对结合半导体光放大器作光开关的此结构的物理模型进行了详细描述,并根据此模型分析了其增益、噪声、信噪比等方面的特性.     

一种高性能的新结构IGBT

提出了一种低功率损耗的新结构IGBT.该新结构的创新点在于其复合耐压层结构,该耐压层包括深扩散形成的n型缓冲层和硼注入形成的透明背发射区两部分.虽然在正常工作条件下,该新结构IGBT工作于穿通状态,但器件仍具有非穿通IGBT(NPT-IGBT)的优良特性.该新结构IGBT具有比NPT-IGBT更薄的芯片厚度,从而可以获得更好的通态压降和关断功耗之间的折衷.实验结果表明:与NPT-IGBT相比较,新结构IGBT的功率损耗降低了40%.     

微桥法镍膜的弹性模量和残余应力测量

利用MEMS技术制作了不同尺寸的镍(Ni)膜微桥结构样品。采用纳米压痕仪XP系统测量了微桥载荷与位移的关系,并结合微桥力学理论模型得到了两种不同尺寸的Ni膜的弹性模量和残余应力。结果表明,两种不同尺寸的Ni膜的弹性模量结果一致,为190 GPa左右,但是残余应力变化较大。与采用纳米压痕仪直接测得的带有硅(Si)基底的Ni膜弹性模量186.8 7.5 GPa相比较,两者符合较好。     

基于支持向量机的缓存预估模型的设计与实现

采用支持向量机(SVM)对网络业务流数据进行预测估计，通过训练样本，从而获得样本以外数据的分布规律。在此基础上，设计了一种网络排队队列缓存的预估模型。实验表明，该模型具有较高的训练效率和很高的估计精确度。     

(111)择优取向的Pb(Zr0.52Ti0.48)O3铁电薄膜的制备及研究

选用不同浓度的Pb(Zr_0.52Ti_0.48)O₃溶胶，用Sol-gel法在Pt/Ti/SiO₂/Si基片上沉积一层厚度不同的Pb(Zr_0.52Ti_0.48)O₃ (PZT52)过渡层，经400℃烘烤、550℃退火等程序后，再用Sol-gel法在PZT52过渡层上沉积Pb(Zr_0.52Ti_0.48)O _{关键词： PZT铁电薄膜 择优取向 过渡层 剩余极化强度}     

CsI(Tl)晶体中反冲Cs和I核Quenching?Factor的测量

许多实验对用CsI(Tl)闪烁晶体作为探测器来寻找和探测暗物质的可行性进行了研究.本工作利用8MeV单能中子轰击CsI(Tl)晶体探测器来研究Cs核和I核的QuenchingFactor.在数据处理中,运用脉冲形状甄别(PSD)方法来分辨反冲核信号和本底信号.实验结果表明,在7keV到132keV的能区中,Quench ingFactor随着反冲核能量的减少而增加.在探测暗物质的实验中,这一性质对于CsI(Tl)晶体探测器获得较低的能量阈值是很有利的.