Micromachining of circular ring microstructure by femtosecond laser pulses

In this paper, integration of interference phenomenon into femtosecond laser micromachining was reported as the femtosecond laser pulses were reshaped spatially to perform ablation. The generation of circular interference pattern was demonstrated by overlapping infrared femtosecond laser pulses. The interference pattern was subsequently focused on a copper substrate to ablate microstructures of concentric circular rings. The present technique is expected to open up new applications in the areas of rapid fabrication of micro-Fresnel lenses, hybrid microlenses and lens arrays.     

Real-time recursive estimation of statistical parameters

Recursive algorithms for the computation of standard deviation and average deviation are derived and their applications in data acquisition are discussed. The relative speeds and accuracies of the two algorithms are compared for synthetic data. The performance of recursive estimation under shot and proportional noise limitations is also described. As an example of the utility of these algorithms, absorbance data with constant confidence intervals are collected regardless of incident and transmitted intensities. The desired precision is specified prior to data acquisition and used to control signal-averaging of the data in real time.     

Silicon-Based Integrated Optic Pressure Sensor Using Intermodal Interference between TM-Like and TE-Like Modes

In this paper, a silicon-based integrated optic pressure sensor using an intermodal interference between the fundamental TM-like and TE-like modes is described. The sensor consists of a micromachined rectangular diaphragm and a straight polystyrene optical waveguide passing over the diaphragm. Its sensitivity is theoretically known to be strongly dependent on the position of the waveguide over the diaphragm. To experimentally investigate such dependence, we fabricated a sensor with a 1.2 mm ×10 mm ×20 μm diaphragm, over which waveguides were placed at 50 μm intervals. The measured phase sensitivity was 98 mrad/kPa for the waveguide nearest to the diaphragm edge. The measurement was also carried out for the other waveguides. As theoretically expected, the largest sensitivity was obtained for the waveguide nearest to the edge.     

All-optical frequency multiplication/recovery based on a semiconductor optical amplifier ring cavity

A novel scheme for all-optical frequency multiplication/recovery based on a semiconductor optical amplifier ring cavity is proposed and investigated numerically. The results show, for a 2.5 GHz driving pulse train, it can be generated 5-25 GHz repetition rate pulse trains with low clock amplitude jitter, polarization independence and high peak power. Furthermore, the extraction of the clock signal from a pseudorandom bit sequence signal can be realized based on the proposed scheme.     

Interference of probabilities and number field structure of quantum models

We study the probabilistic consequences of the choice of the basic number field in the quantum formalism. We demonstrate that by choosing a number field for a linear space representation of quantum model it is possible to describe various interference phenomena. We analyse interference of probabilistic alternatives induced by real, complex, hyperbolic (Clifford) and p‐adic representations.     

一种高信噪比的双光束激光光声光谱仪原理及应用

作为一种新兴的检测手段 ,激光光声光谱技术与其他检测技术相比具有很多优点。本文设计的光声光谱仪用激光做光源 ,有两个光声池 ,分别用来放置参考样品和待测样品 ,输出结果为二者光声信号的比值。利用这一比值 ,可以由参考样品的性能参数方便地求出待测样品的相关性能参数。该光声光谱仪有效地减小了本底吸收噪声的影响 ,提高了信噪比 ,扩大了固体光声理论的应用范围。本文还阐述了该光声光谱仪在定性定量分析中的一些应用     

用于波分复用系统的多峰干涉滤光片

介绍了用于波分复用系统的多峰干涉滤光片的设计原理,提出了滤光片透射峰位置的确定方法,讨论了影响滤光片半宽度和截止度的因素,给出了滤光片的膜厚容差分析结果,表明透射率监控标准偏差在<0.5%范围内,可以得到波形良好的多峰滤光片,最后给出了实验结果.     

激光等离子体探针及应用研究

本文介绍用阴影、纹影相干涉方法确定等离子体折射系数变化的原理。分析了等离子体中的非线性效应和对光探测系统的基本要求。并简要叙述了实验上采用的后向喇曼探测束,给出了等离子体干涉、纹影和阴影的测量结果。     

Point load determination of static elastic moduli using laser speckle interferometry

Electronic speckle interferometry (ESPI) is used to determine the Young's modulus E and Poisson ratio ν of an isotropic material. Micron scale deformations of the surface of the block of polymethyl-methacrylate (PMMA) are induced by normal application of a known near-point force. These deformations are recorded in speckle interferometric fringe patterns. An iterative minimum error inversion technique is developed to obtain the elastic properties from the positions of fringe peaks and troughs observed in the fringe patterns. Sensitivity tests of the method on calculated fringe patterns using measured experimental uncertainties suggest the technique will provide measures of the elastic moduli to better than 5%. In an experimental test on a bloc of PMMA (acrylic) the technique gave values of E and ν that differed from corresponding measures obtained using more conventional strain-gauge methods by less than 4%.     

Signal averaging in gas chromatography

Ensemble or signal averaging, and the use of the technique for the solution of some unique problems with minimum sample handling, have previously been reported. The capability of the technique has been evaluated with microbore gas chromatography for the fast handling of a large number of analyses: ca 20–30 replicate injections are easily attainable in a reasonable analysis time. The implementation of the signal averaging technique with other concentration techniques for improving detection limits is also demonstrated.