基于XPS对硫铁矿去除SeO2-3的机理研究

硒是动植物及人体生长必需的十五种微量元素之一，具有清除体内自由基、抗氧化、增强免疫力等功能，但其安全剂量的范围却很窄。利用扫描电子显微镜（SEM）和X射线衍射仪（XRD）对湿法球磨制备的硫铁矿形貌进行了表征。SEM观测发现加乙醇助磨后的硫铁矿为粒径大小较均匀的球形颗粒团聚体，粒径范围在17～200 nm之间，平均粒径138 nm。XRD衍射图谱中的特征峰与FeS₂衍射图谱中各峰位置基本一致，因此判定硫铁矿中主要化学组分为FeS₂，且图谱中基本没有杂峰，表明制备过程中并未混入杂质，样品纯度较高。实验结果表明，该法制备的硫铁矿具有颗粒粒径小、比表面积大、反应活性高等优点。研究中利用X射线光电子能谱仪（XPS）对硫铁矿去除水体中SeO2-₃的机理进行了研究。研究结果表明, （1）在较为广泛的实验pH范围（pH 2.2～11.5），硫铁矿均能有效去除水体中SeO2-₃，去除效率（除pH值7.8以外）均达到90%以上；（2）硫铁矿与SeO2-₃发生反应后，其主要组成元素的XPS特征峰结合能有所减小，表明硫铁矿表面发生了一定化学变化；（3）酸碱环境下硫铁矿去除SeO2-₃的机理不完全相同，酸性环境下，硫铁矿对SeO2-₃的去除是单纯的氧化还原过程，即硫铁矿中被酸活化的S2-₂将SeO2-₃还原为单质Se(0)，并且酸性越强，SeO2-₃去除效果越好；碱性环境下，SeO2-₃的去除过程中氧化还原与络合反应并存，硫铁矿表面有络合态Fe(OH)SeO₃和单质Se(0)两种存在形态，且碱性越强，络合态Fe(OH)SeO₃含量越高。以上研究结果为硫铁矿去除固定水体和土壤中以SeO2-₃为代表的可变价金属阴离子提供重要理论依据和应用基础。     

Fluid‐structure coupling of linear elastic model with compressible flow models

Cavitation erosion is caused in solids exposed to strong pressure waves developing in an adjacent fluid field. The knowledge of the transient distribution of stresses in the solid is important to understand the cause of damaging by comparisons with breaking points of the material. The modeling of this problem requires the coupling of the models for the fluid and the solid. For this purpose, we use a strategy based on the solution of coupled Riemann problems that has been originally developed for the coupling of 2 fluids. This concept is exemplified for the coupling of a linear elastic structure with an ideal gas. The coupling procedure relies on the solution of a nonlinear equation. Existence and uniqueness of the solution is proven. The coupling conditions are validated by means of quasi‐1D problems for which an explicit solution can be determined. For a more realistic scenario, a 2D application is considered where in a compressible single fluid, a hot gas bubble at low pressure collapses in a cold gas at high pressure near an adjacent structure.     

Nanocomposite hydrogel consisting of Na‐montmorillonite with enhanced mechanical properties

A new kind of nanocomposite (NC) hydrogel with Na‐montmorillonite (MMT) is presented in this article. The NC hydrogels were synthesized by free radical copolymerization of acrylamide and (3‐acrylamidopropyl) trimethylammonium chloride (ATC) in the presence of MMT and N,N′‐methylene‐bis‐acrylamide used as chemical cross‐linker. Due to the cation‐exchange reaction between MMT and ATC (cationic monomer) during the synthesis of NC hydrogels, MMT platelets were considered chemical “plane” cross‐linkers, different from “point” cross‐linkers. With increasing amount of MMT, the crosslinking degree enhanced, causing a decrease of the swelling degree at equilibrium. Investigations of mechanical properties indicated that NC hydrogels exhibited enhanced strength and toughness, which resulted from chemical interaction between exfoliated MMT platelets and polymer chains in hydrogels. Dynamic shear measurements showed that both storage modulus and loss modulus increased with increasing MMT content. The idea described here provided a new route to prepare hydrogels with high mechanical properties by using alternative natural Na‐MMT. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1020–1026     

Path to achieving molecular dispersion in a dense reactive mixture

A uniform dispersion of reactants is necessary to achieve a complete reaction involving multicomponents. In this study, we have examined the role of plasticizer in the reaction of two seemingly unlikely reactants: a highly crystalline hexamethylenetetramine (HMTA) and a strongly hydrogen bonded phenol formaldehyde resin. By combining information from NMR, infrared spectroscopy and differential scanning calorimetry, we were able to determine the role of specific intermolecular interactions necessary for the plasticizer to dissolve the highly crystalline HMTA and to plasticize the phenol formaldehyde resin in this crosslinking reaction. The presence of the plasticizer increased the segmental mobility, disrupted the hydrogen bonded matrix, and freed the hydroxyl units, which further increased the solubility of the HMTA. Both the endothermic and exothermic transitions are accounted for in the calorimetric data obtained. For the first time, it is possible to obtain the effective molar ratio of each component needed to complete the crosslinking reaction efficiently. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1519–1526     

DFT mechanistic study of the H2‐assisted chain transfer copolymerization of propylene and p‐methylstyrene catalyzed by zirconocene complex

DFT computations have been performed to investigate the mechanism of H₂‐assisted chain transfer strategy to functionalize polypropylene via Zr‐catalyzed copolymerization of propylene and p‐methylstyrene (pMS). The study unveils the following: (i) propylene prefers 1,2‐insertion over 2,1‐insertion both kinetically and thermodynamically, explaining the observed 1,2‐insertion regioselectivity for propylene insertion. (ii) The 2,1‐inserion of pMS is kinetically less favorable but thermodynamically more favorable than 1,2‐insertion. The observation of 2,1‐insertion pMS at the end of polymer chain is due to thermodynamic control and that the barrier difference between the two insertion modes become smaller as the chain length becomes longer. (iii) The pMS insertion results in much higher barriers for subsequent either propylene or pMS insertion, which causes deactivation of the catalytic system. (iv) Small H₂ can react with the deactivated [Zr]?pMS?PP_n facilely, which displace functionalized pMS?PP_n chain and regenerate [Zr]? H active catalyst to continue copolymerization. The effects of counterions are also discussed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 576–585     

基于吸收系数的生脉注射液中聚山梨酯80含量测定新方法

聚山梨酯80又名吐温80，为一种亲水型非离子表面活性剂，是食品、保健品和药品中常用的辅料，作为增溶剂和澄清剂广泛用于中药注射剂。近年来，不良反应的发生使得聚山梨酯80的质量和应用愈加受到重视，有研究认为其加入可能引起注射剂不良反应增加。为避免超量使用，有必要对该辅料的投料加以严格控制。中药注射剂中聚山梨酯80的含量测定是当下研究的热点和难点，可以通过分光光度法、分子排阻-蒸发光散射检测法(SEC-ELSD)、液质联用法(LC-MS)直接测定，也可以水解后法经液相色谱-紫外检测法(HPLC-UV)或气相色谱法(GC)间接测定。但由于聚山梨酯80为聚氧乙烯聚合数目不同的混合物、不同厂家生产的聚山梨酯80化学组分及比例存在较大差异，难以采用统一的转换公式或对照品准确定量。此外，中药注射剂的复杂基质造成的假阳性干扰也对定量提出了挑战。为解决以上问题，以生脉注射液为例，提出基于吸收系数的中药注射剂中聚山梨酯80含量测定新方法。优化检测波长、显色剂种类、液液萃取过程振荡和静置时间，在6个不同品牌仪器上测得聚山梨酯80-硫氰酸钴配合物的吸收系数(E1%_{1 cm})为104.23，相对标准偏差(RSD)为2.08%。生脉注射液稀释10倍后，精密量取供试品溶液1.0 mL，精密加入硫氰酸钴溶液10 mL，二氯甲烷20 mL，涡旋振荡3 min。将混合液移至分液漏斗中，静置30 min，取下层二氯甲烷液，将前1 mL弃去，接收约15 mL，在320 nm处测定吸光度，再根据Lambert-Beer定律，利用获得的吸收系数计算得到聚山梨酯80的含量。方法阴性无干扰，精密度和重复性相对标准偏差均低于3%，平均回收率为98.42%。为进一步验证方法的准确性，分别采用吸收系数法和标准曲线法测定了2个厂家的10批生脉注射液，并与实际投料量比较。配对t检验结果表明，当置信度为95%时，两种方法无显著性差异，吸收系数法测得结果与企业生产中聚山梨酯的实际投料量也无显著性差异。研究采用前人未采用的、灵敏度更高的320 nm为检测波长，显著降低了基质干扰，克服了中药注射剂中聚山梨酯80测定结果与实际投料量难以吻合的问题。吸收系数法无需使用对照品，亦不用制备标准曲线，可为中药注射剂中聚山梨酯80的检查标准提供切实可行的解决方案。所建方法灵敏、准确、快速、简便，为含聚山梨酯80制剂的质量控制提供了关键常数及新的思路。