AIN/蓝宝石模板上生长的GaN研究

研究了在分子束外延制备的AIN/蓝宝石模板上采用金属有机物化学气相外延生长的非故意掺杂GaN的材料性质.采用X射线衍射(XRD)、透射电镜(TEM)和原子力显微镜研究了AIN模板的晶体质量和表面相貌对GaN的影响.结果表明,当AIN的表面粗糙度较小时,尽管AIN模板的位错密度较高((102)面XRD ω扫描半高全宽900-1500 arcsec),但生长得到的GaN依然具有和在蓝宝石衬底上采用"二步法"生长的GaN可比拟的晶体质量((002)面XRD ω扫描半高伞宽200-300 arcsec,(102)面400-500 arcsec)和表面粗糙度(0.1-0.2 nm).TEM照片表明GaN中位错密度降低的原因是AIN中的一部分位错在AIN和GaN的界面处被终止而未能延伸至GaN中.这可能是因为Ga原子尺寸较大,具有修复晶格缺陷的作用.而当AIN的表面粗糙度较大时,Ga原子在MOVPE生长过程中的迁移受到影响.得到的GaN晶体质量非常差.此外,采用范德堡法测量的GaN电阻率为105-106Ω·cm,比蓝宝石衬底上生长的GaN高大约6个数量级,这被认为是采用AIN代替GaN低温缓冲层所致.     

AlN/蓝宝石模板上生长的GaN研究

研究了在分子束外延制备的AlN/蓝宝石模板上采用金属有机物化学气相外延生长的非故意掺杂GaN的材料性质.采用X射线衍射(XRD)、透射电镜(TEM)和原子力显微镜研究了AlN模板的晶体质量和表面相貌对GaN的影响.结果表明,当AlN的表面粗糙度较小时,尽管AlN模板的位错密度较高((102)面XRD ω扫描半高全宽900—1500 arcsec),但生长得到的GaN依然具有和在蓝宝石衬底上采用"二步法"生长的GaN可比拟的晶体质量((002)面XRD ω扫描半高全宽200—30 关键词： 氮化镓 氮化铝 金属有机物化学气相外延     

腐蚀时间对蓝宝石衬底上外延生长GaN质量的影响

使用熔融的KOH在高温下对c面蓝宝石衬底进行不同时间的腐蚀,借助扫描电镜、原子力显微镜对衬底表面进行了表征,然后利用金属有机物化学气相沉积设备在不同腐蚀时间的衬底样品上进行了GaN材料的外延生长。通过X射线衍射结果比较了两组衬底上外延材料的质量,利用原子力显微镜结果对外延层表面形貌进行了分析,最后论述了腐蚀时间的调整对蓝宝石衬底上外延生长氮化镓质量的影响机理。     

高电子迁移率晶格匹配InAlN/GaN材料研究

文章基于蓝宝石衬底采用脉冲金属有机物化学气相淀积(MOCVD)法生长的高迁移率InAlN/GaN材料,其霍尔迁移率在室温和77 K下分别达到949和2032 cm²/Vs,材料中形成了二维电子气(2DEG). 进一步引入1.2 nm的AlN界面插入层形成InAlN/AlN/GaN结构,则霍尔迁移率在室温和77 K下分别上升到1437和5308 cm²/Vs. 分析样品的X射线衍射、原子力显微镜测试结果以及脉冲MOCVD生长方法的特点,发现InAlN/GaN材料的结晶质量较高,与GaN晶格匹配的InAlN材料具有平滑的表面和界面. InAlN/GaN和InAlN/AlN/GaN材料形成高迁移率特性的主要原因归结为形成了密度相对较低(1.6×10¹³-1.8×10¹³ cm^-2)的2DEG,高质量的InAlN晶体降低了组分不均匀分布引起的合金无序散射,以及2DEG所在界面的粗糙度较小,削弱了界面粗糙度散射. 关键词： InAlN/GaN 脉冲金属有机物化学气相淀积 二维电子气 迁移率     

N极性GaN薄膜的MOCVD外延生长

采用MOCVD技术在c面蓝宝石衬底上外延制备了N极性GaN薄膜。通过KOH腐蚀的方法判定了GaN外延薄膜的极性。通过X射线双晶衍射(XRD)摇摆曲线和光致荧光(PL)谱测试研究了成核层生长时间对N极性GaN薄膜晶体质量和发光性能的影响。研究结果表明,成核层生长时间为300 s时,N极性GaN薄膜样品的位错密度最低,发光性能最好。采用拉曼(Raman)光谱对样品的应变状态进行了分析。     

位错形态与GaN外延薄膜电阻率之间的关系

利用金属有机化学气相沉积（MOCVD）,通过改变生长过程中成核层退火阶段的反应室压力,在蓝宝石衬底上制得了不同阻值的GaN外延薄膜。利用原子力显微镜（AFM）、X射线衍射（XRD）和透射电子显微镜（TEM）对所生长的GaN薄膜的表面形貌、位错密度和位错形态进行了研究。结果表明,GaN的电阻率与位错形态之间存在密切联系,由此建立了模型来解释两者之间的关系。由于刃型位错附近存在负电荷,因此可为电子提供传导通道。在低阻GaN中,绝大多数位错发生弯曲和相互作用,在平行于基底方向上形成负电荷的导通通道,GaN薄膜的电导率较高。在高阻GaN中,位错生长方向垂直于基底,负电荷很难在平行于基片方向上传导,GaN薄膜的电导率很低,由此得到高阻GaN。     

侧向外延法生长的高质量GaN及其外延缺陷的观察

在有条状SiO2图形的GaN“模板”上,侧向外延方法生长了高质量的GaN。荧光显微镜的结果表明在SiO2掩膜区有成核过程发生。原因可能是SiO2的质量不高,为GaN的生长提供了一些成核中心。在GaN层的厚度达到4．5μm后,侧向的融合开始发生。侧向生长的速度与垂直生长速度几乎相同。在所有的SiO：掩膜上方都形成了空洞。样品在240℃熔融的KOH中腐蚀13min。在SiO2掩膜区生长的GaN,其腐蚀坑密度(相当于穿透位错密度)减少到几乎为零。而在窗口区生长的GaN,腐蚀坑密度仍然很高,达到10^8cm^-2量级。同时,我们发现具有不同窗口尺寸的样品在SiO2掩膜区上侧向生长的CaN的晶体质量基本相同,与窗口区的宽度几乎无关。室温光荧光结果表明侧向外延法生长的CaN中的晶格失配应力已被部分释放。     

p型GaN低温粗化提高发光二极管特性

利用金属有机物化学气相沉积技术在蓝宝石衬底上低温生长GaN:Mg薄膜,对不同源流量的GaN:Mg材料特性进行优化研究.研究表明二茂镁(CP2Mg)和三甲基镓(TMGa)物质的量比([CP2Mg]/[TMGa])在1.4×10-3—2.5×10-3范围内,随[CP2Mg]/[TMGa]增加,晶体质量提高,空穴浓度线性增加.当[CP2Mg]/[TMGa]为2.5×10-3时获得空穴浓度与在较高温度生长获得的空穴浓度相当,且薄膜表面较粗糙.采用[CP2Mg]/[TMGa]为2.5×10-3的p型GaN层制备的发光二极管,在注入电流为20mA时,输出光强提高了17.2%.     

掺Fe高阻GaN缓冲层特性及其对AlGaN/GaN高电子迁移率晶体管器件的影响研究

利用金属有机物化学气相沉积技术在蓝宝石衬底上制备了掺Fe高阻Ga N以及Al Ga N/Ga N高电子迁移率晶体管(HEMT)结构.对Cp_2Fe流量不同的高阻Ga N特性进行了研究.研究结果表明,Fe杂质在Ga N材料中引入的Fe~(3+/2+)深受主能级能够补偿背景载流子浓度从而实现高阻,Fe杂质在Ga N材料中引入更多起受主作用的刃位错,也在一定程度上补偿了背景载流子浓度.在一定范围内,Ga N材料方块电阻随Cp_2Fe流量增加而增加,Cp_2Fe流量为100 sccm(1 sccm 1mL min)时,方块电阻增加不再明显;另外增加Cp_2Fe流量也会导致材料质量下降,表面更加粗糙.因此,优选Cp_2Fe流量为75 sccm,相应方块电阻高达×10?/,外延了不同掺Fe层厚度的Al Ga N/Ga N HEMT结构,并制备成器件.HEMT器件均具有良好的夹断以及栅控特性,并且增加掺Fe层厚度使得HEMT器件的击穿电压提高了39.3%,同时对器件的转移特性影响较小.     

外延在蓝宝石衬底上的非掺杂GaN研究

采用改变生长条件的方法制备GaN薄膜,在(0001)面蓝宝石衬底上利用金属有机物化学气相沉积技术制备了不同样品,并借助X射线双晶衍射仪(XRD)、PL谱测试仪和光学显微镜对材料进行了分析。XRD(0002)面和(1012)面测试均表明TMGa流量为70 cm3/min时样品位错密度最低。利用该TMGa流量进一步制备了改变生长温度的样品。XRD和PL谱测试结果表明,提高生长温度有利于提高GaN样品的晶体质量和光学性能。最后,利用光学显微镜对样品的表面形貌进行了分析。     

Enhancement-mode AlGaN/GaN high electronic mobility transistors with thin barrier

An enhancement-mode (E-mode) AlGaN/GaN high electron mobility transistor (HEMTs) was fabricated with 15-nm AlGaN barrier layer. E-mode operation was achieved by using fluorine plasma treatment and post-gate rapid thermal annealing. The thin barrier depletion-HEMTs with a threshold voltage typically around --1.7 V, which is higher than that of the 22-nm barrier depletion-mode HEMTs (--3.5 V). Therefore, the thin barrier is emerging as an excellent candidate to realize the enhancement-mode operation. With 0.6-μ m gate length, the devices treated by fluorine plasma for 150-W RF power at 150 s exhibited a threshold voltage of 1.3 V. The maximum drain current and maximum transconductance are 300 mA/mm, and 177 mS/mm, respectively. Compared with the 22-nm barrier E-mode devices, V_T of the thin barrier HEMTs is much more stable under the gate step-stress.     

Fluorine-plasma treated AlGaN/GaN high electronic mobility transistors under off-state overdrive stress

Influences of off-state overdrive stress on the fluorine-plasma treated AlGaN/GaN high-electronic mobility transistors (HEMTs) are experimentally investigated. It is observed that the reverse leakage current between the gate and source decreases after the off-state stress, whereas the current between the gate and drain increases. By analyzing those changes of the reverse currents based on the Frenkel-Poole model, we realize that the ionization of fluorine ions occurs during the off-state stress. Furthermore, threshold voltage degradation is also observed after the off-state stress, but the degradations of AlGaN/GaN HEMTs treated with different F-plasma RF powers are different. By comparing the differences between those devices, we find that the F-ions incorporated in the GaN buffer layer play an important role in averting degradation. Lastly, suggestions to obtain a more stable fluorine-plasma treated AlGaN/GaN HEMT are put forwarded.     

Neutron irradiation effects on AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) were exposed to 1 MeV neutron irradiation at a neutron fluence of 1 × 10¹⁵ cm^-2. The dc characteristics of the devices, such as the drain saturation current and the maximum transconductance, decreased after neutron irradiation. The gate leakage currents increased obviously after neutron irradiation. However, the rf characteristics, such as the cut-off frequency and the maximum frequency, were hardly affected by neutron irradiation. The AlGaN/GaN heterojunctions have been employed for the better understanding of the degradation mechanism. It is shown in the Hall measurements and capacitance-voltage tests that the mobility and concentration of two-dimensional electron gas (2DEG) decreased after neutron irradiation. There was no evidence of the full-width at half-maximum of X-ray diffraction (XRD) rocking curve changing after irradiation, so the dislocation was not influenced by neutron irradiation. It is concluded that the point defects induced in AlGaN and GaN by neutron irradiation are the dominant mechanisms responsible for performance degradations of AlGaN/GaN HEMT devices.     

Breakdown mechanisms in AlGaN/GaN high electron mobility transistors with different GaN channel thickness values

In this paper,the off-state breakdown characteristics of two different AlGaN/GaN high electron mobility transistors（HEMTs）,featuring a 50-nm and a 150-nm GaN thick channel layer,respectively,are compared.The HEMT with a thick channel exhibits a little larger pinch-off drain current but significantly enhanced off-state breakdown voltage(SV_off).Device simulation indicates that thickening the channel increases the drain-induced barrier lowering（DIBL） but reduces the lateral electric field in the channel and buffer underneath the gate.The increase of BV_off in the thick channel device is due to the reduction of the electric field.These results demonstrate that it is necessary to select an appropriate channel thickness to balance DIBL and BV_off in AlGaN/GaN HEMTs.     

High temperature characteristics of AlGaN/GaN high electron mobility transistors

Direct current (DC) and pulsed measurements are performed to determine the degradation mechanisms of AlGaN/GaN high electron mobility transistors (HEMTs) under high temperature. The degradation of the DC characteristics is mainly attributed to the reduction in the density and the mobility of the two-dimensional electron gas (2DEG). The pulsed measurements indicate that the trap assisted tunneling is the dominant gate leakage mechanism in the temperature range of interest. The traps in the barrier layer become active as the temperature increases, which is conducive to the electron tunneling between the gate and the channel. The enhancement of the tunneling results in the weakening of the current collapse effects, as the electrons trapped by the barrier traps can escape more easily at the higher temperature.     

Investigation of AlGaN/GaN fluorine plasma treatment enhancement-mode high electronic mobility transistors by frequency-dependent capacitance and conductance analysis

This paper reports fluorine plasma treatment enhancement-mode HEMTs (high electronic mobility transistors) EHEMTs and conventional depletion-mode HEMTs DHEMTs fabricated on one wafer using separate litho-photography technology. It finds that fluorine plasma etches the AlGaN at a slow rate by capacitance--voltage measurement. Using capacitance--frequency measurement, it finds one type of trap in conventional DHEMTs with τ_T=(0.5-6) ms and D_T= (1 - 5) × 10¹³ cm^-2·eV^-1. Two types of trap are found in fluorine plasma treatment EHEMTs, fast with τ_T(f)=(0.2-2) μs and slow with τ_T(s)=(0.5-6) ms. The density of trap states evaluated on the EHEMTs is D_T(f)=(1 - 3) × 10¹² cm^-2·eV^-1 and D_T(s)=(2 - 6) × 10¹² cm^-2·eV^-1 for the fast and slow traps, respectively. The result shows that the fluorine plasma treatment reduces the slow trap density by about one order, but introduces a new type of fast trap. The slow trap is suggested to be a surface trap, related to the gate leakage current.     

Effects of SiNx on two-dimensional electron gas and current collapse of AlGaN/GaN high electron mobility transistors

SiN_x is commonly used as a passivation material for AlGaN/GaN high electron mobility transistors (HEMTs). In this paper, the effects of SiN_x passivation film on both two-dimensional electron gas characteristics and current collapse of AlGaN/GaN HEMTs are investigated. The SiN_x films are deposited by high- and low-frequency plasma-enhanced chemical vapour deposition, and they display different strains on the AlGaN/GaN heterostructure, which can explain the experiment results.     

Effects of SiNx on two-dimensional electron gas and current collapse of A1GaN/GaN high electron mobility transistors

SiNx is commonly used as a passivation material for AlGaN/GaN high electron mobility transistors (HEMTs). In this paper, the effects of SiN x passivation film on both two-dimensional electron gas characteristics and current collapse of AlGaN/GaN HEMTs are investigated. The SiNx films are deposited by high- and low-frequency plasma-enhanced chemical vapour deposition, and they display different strains on the AlGaN/GaN heterostructure, which can explain the experiment results.