应力导致InAs/In0.15Ga0.85As量子点结构中In0.15Ga0.85As阱层的合金分解效应研究

利用固源分子束外延技术，在In_0.15Ga_0.85As/GaAs量子阱生长了两个InAs/In_0.15Ga_0.85As量子点(DWELL)样品.通过改变其中一个InAs DWELL样品中的In_0.15Ga_0.85As阱层的厚度和生长温度，获得了量子点尺寸增大而且尺寸分布更均匀的结果.结合光致发光光谱(PL)和压电调制光谱(PzR)实验结果，发现该样品量子点的光学性质也同时得到 关键词： 合金分解效应 0.15Ga_0.85As量子点')" href="#">InAs/In_0.15Ga_0.85As量子点 光致发光光谱 压电调制光谱     

InAs/GaAs表面量子点的压电调制反射光谱研究

运用压电调制反射光谱(PzR)方法测量了在以GaAs(311)B为衬底的In_0.35Ga_0.65As模板上生长的InAs表面量子点结构的反射谱.在77K温度下，观察到了来自样品各个组成结构(包括表面量子点本身、被覆盖层覆盖的量子点、In_0.35Ga_0.65As模板以及GaAs衬底等)的调制信号.来自表面量子点本身的调制信号是多个清晰的调制峰.用一阶和三阶微分洛伦兹线形对PzR谱中对应结构的实验数据进行了拟合，精确确定了与样品的各个组成结构相对应的调制峰的能量位置.对不同样品PzR谱的差异进行了定性的说明. 关键词： 压电调制光谱 InAs/GaAs 表面量子点 洛伦兹线形拟合     

In0.2Ga0.8As/GaAs单量子阱PL谱温度特性及其机制

测量了不同阱宽In0.2Ga0.8As/GaAs单量子阱的PL谱的峰值波长和荧光谱线半峰全宽随温度的变化。利用Varshni公式对实验峰值波长进行拟合,得到了新的参数。结果表明,无位错应变量子阱带隙仍具有其体材料的特性:荧光谱线半峰全宽随温度升高迅速展宽,这主要归因于声子关联作用增强和激子热离化为自由载流子所致;阱宽越窄荧光峰值能量越高,将其与量子尺寸效应的理论计算结果进行了比较。文中还考察了谱线半峰全宽和阱宽的关系,利用合金无序对这一现象进行了解释。     

Mn离子注入InAs/GaAs量子点结构材料的光电性质研究

用高能离子注入(160keV)的方法对InAs/GaAs量子点结构进行掺杂，研究了不同退火工艺处理后量子点的光致发光和电学性能.相对于长时间退火，快速退火处理后的量子点发光通常较强.在相同的退火条件下，量子点发光峰位随着Mn注入剂量的增加，先是往高能量端快速移动，而后发光峰又往低能方向移动.后者可能是由于Mn原子进入InAs量子点，释放了InAs量子点中的应变所致.对于高注入剂量样品和长时间退火样品，变温电阻曲线在40 K附近会出现反常行为. 关键词： 离子注入 InAs/GaAs量子点 光致发光 团簇     

压电调制反射光谱研究GaAs/Al0.29Ga0.71 As单量子阱

报道了压电调制反射测量系统的建立,应用该系统获得了势阱宽度分别为5nm和25nm的两个GaAs/Al0.29Ga0.71As单量子阱的压电调制反射谱.从图谱中可以看出,在室温下能够较容易地分辨出和轻、重空穴相关联的子带跃迁.在阱宽25nm的样品中还观察到了自旋-轨道跃迁.利用有效质量理论近似计算,对量子阱样品的图谱结构进行了指认,发现实验值和计算值能够较好地符合.     

利用In0.82Ga0.18As与InP衬底之间的应力制作结构材料的缓冲层

采用低压金属有机化学气相淀积(LP-MOCVD)技术,在InP(100)衬底上生长In0.82Ga0.18As,研究生长温度对In0.82Ga0.18As材料表面形貌、结晶质量和电学性能的影响.利用InP(100)衬底与In0.82Ga0.18As材料晶格失配所产生的应变,在不同的生长温度下应变释放程度不同,进而在In...     

In0.53Ga0.47As/InP量子阱与体材料的1 MeV电子束辐照光致发光谱研究

为获得对In_0.53Ga_0.47As/InP材料在电子束辐照下的光致发光谱变化规律, 开展了1 MeV电子束辐照试验, 注量为 5×10¹²-9×10¹⁴ cm^-2. 样品选取量子阱材料和体材料, 在辐照前后, 进行了光致发光谱测试, 得到了不同结构In_0.53Ga_0.47As/InP材料在1 MeV电子束辐照下的不同变化规律; 对比分析了参数退化的物理机理. 结果显示: 试验样品的光致发光峰强度随着辐照剂量增大而显著退化. 体材料最先出现快速退化, 而五层量子阱在注量达到6×10¹⁴ cm^-2时, 就已经退化至辐照前的9%. 经分析认为原因有: 1)电子束进入样品后, 与材料晶格发生能量传递, 破坏晶格完整性, 致使产生的激子数量减少, 光致发光强度降低; 电子束辐照在材料中引入缺陷, 增加了非辐射复合中心密度, 导致载流子迁移率降低. 2)量子阱的二维限制作用使载流子运动受限, 从而能够降低载流子与非辐射复合中心的复合概率; 敏感区域截面积相同条件下, 体材料比量子阱材料辐射损伤更为严重. 3)量子阱的层数越多, 则异质结界面数越多, 相应的产生的界面缺陷数量也随之增多, 辐射损伤越严重.     

两个子带占据的In0.53Ga0.47As/In0.52Al0.48As量子阱中填充因子的变化规律

研究了低温(1.5K)和强磁场(0-13T)条件下,InP基In0.53Ga0.47As/In0.52Al0.48As量子阱中电子占据两个子带时填充因子随磁场的变化规律.结果表明,在电子自旋分裂能远小于朗道能级展宽的情况下,如果两个子带分裂能是朗道分裂能的整数倍时,即⊿E21=κ*ωc(其中κ为整数),填充因子为偶数;当两个子带分裂能为朗道分裂能的半奇数倍时,即⊿E21=(2κ 1*ω/2,填充因子出现奇数.     

生长温度对In_(0.5)Ga_(0.5)As/GaAs量子点尺寸的影响

采用分子束外延(MBE)技术制备In_(0.5)Ga_(0.5)As/GaAs量子点,利用扫描隧道显微镜(STM)对不同衬底温度下生长的样品进行表征分析.研究表明量子点密度随温度升高先增大后减小,其尺寸随温度的升高而增大.另外,量子点以S-K模式生长并受Ostwald熟化机制影响,其尺寸增大所需的能量来自应变能和温度提供的能量,高温条件下表面原子的解吸附作用会限制量子点的生长.     

蓝光激光器结构中InGaN/GaN多量子阱界面效应的精细光致发光光谱研究

金属有机化学气相沉积(MOCVD)方法制备InGaN/GaN多量子阱结构时,在GaN势垒层生长的N2载气中引入适量H2,能够有效改善阱/垒界面质量从而提升发光效率.本工作利用光致发光(PL)光谱技术,对蓝光激光器结构中的InGaN/GaN多量子阱的发光性能进行了精细的光谱学测量与表征,研究了通H2生长对量子阱界面的调控...     

High and abrupt breakdown voltage In0.15Ga0.85As0.14Sb0.86/GaSb junctions grown by LPE

p-GaInAsSb/n-GaSb junction with breakdown voltages as high as 38 V and abrupt breakdown characteristic have been fabricated by Liquid Phase Epitaxy. To obtain these characteristics the structures have been submitted to annealing processes just after epitaxial growth. The diffusion of dopant from the n-GaSb substrate towards the epitaxial layer separates the electrical junction from the epitaxial interface and produces junctions with better inverse polarization behavior.     

MOCVD-Ga0.4In0.6As0.85P0.15/InP分布布喇格反射镜的反射率

采用MOCVD方法在InP衬底上制备了高质量的四元合金Ga0.4In0.6As0．85P0.15和InP外延层,用椭圆偏光仪测得Ga0.4In0.6As0.85P0.15和InP外延层的折射率。由这两种具有不同折射率的半导体材料交替生长构成不同周期的分布布喇格反射镜(DBR)。研究了不同周期的DBR结构的反射率与波长及反射率与DBR结构周期数的关系。根据多层膜增反原理,当中心波长为1．55um时,反射率随周期数增加迅速增加,周期数为23时,反射率可达99．97％。利用MOCVD技术,通过Ga0.4In0.6As0.85P0.15/InP的交替生长,成功地获得周期数分别为3,4,7,11,15,19,23的分布布喇格反射镜(DBR)。实验结果表明,已获得表面如镜面状的二元InP外延层,而组分x,y分别为0．4,0．85的四元合金,因其处于混溶隙,外延层表面较粗糙,未获得镜面状表面。反射率的测量结果表明,反射镜的反射率随周期数的增加而升高,当DBR的周期数为23时,反射率为54．44％,与理论结果尚存在一定差距。     

Investigation of barrier tunneling characteristics of symmetrical double quantum well in In0.25Ga0.75As/GaAs/In0.25Ga0.75As heterostructure

The optical and electrophysical properties of the GaAs/In_0.25Ga_0.75As heterostructure with a symmetric double quantum well have been investigated. The influence of tunneling electrons and holes through an internal barrier of the quantum well on the shift and splitting of the quantum levels is analyzed. The theoretical estimates are compared with the results of the photoluminescence and photoconductivity measurements. The Hall measurements indicate that the barrier strongly affects the mobility of charge carriers.     

In0.53Ga0.47AS/In0.52Al0.48As量子阱中的正磁电阻效应

在低温强磁场条件下,对In0.53 Ga0.47 As/In0.52AI0.48As量子阱中的二维电子气进行了磁输运测试.在低磁场范围内观察到正磁电阻效应,在高磁场下这一正磁电阻趋于饱和,分析表明这一现象与二维电子气中的电子占据两个子带有关.在考虑了两个子带之间的散射效应后,通过分析低磁场下的正磁电阻,得到了每个子带电子的迁移率,结果表明第二子带电子的迁移率高于第一子带电子的迁移率.进一步分析表明,这主要是由两个子带之间的散射引起的.     

Recombination in tensile-strained In0.3Ga0.7As quantum well on InP

Photoluminescence (PL) measurements under different excitation powers were carried out at low temperature on tensile-strained In_0.3Ga_0.7As single wells of 6 nm with InGaAs barriers lattice matched to InP substrate. PL measurements taken at 2 K show a main emission band at 0.762 eV probably originating from a type-II transition. The insertion of an ultrathin InAs layer at In_0.3Ga_0.7As on In_0.53Ga_0.47As interface reveals an additional feature at 0.711 eV as well as an excited-state luminescence emission at high pump powers. The InAs insertion improves heterointerface quality, which was confirmed by an increase in PL intensity.     

Study of single event effect for the InP-based HEMT with In0.53Ga0.47As/In0.3Ga0.7As/In0.7Ga0.3As composite channel

In this study, the single event effects in In_0.53Ga_0.47As/In_0.3Ga_0.7As/In_0.7Ga_0.3As composite channel InP-based HEMT are investigated using TCAD simulation for the first time. Due to the higher conduction band difference between bottom In_0.7Ga_0.3As channel and InAlAs buffer, the electrons in the buffer layer induced by ions strike cannot enter the channel, led to reduce the peak concentration in the composite channel and significantly weakened the drain current for composite channel device. Meanwhile, higher barrier height under the gate for composite channel InP-based HEMT is formed after particle strike, and further attenuate the drain current. Therefore, the single event effects can be effectively reduced by designing channel structure. In addition, drain voltage and incident position also show significant impact drain current. With the increase in the drain voltage, the drain current increase and the most sensitive incident position is the gate electrode for the device.     

Effect of a Coulomb well in (In,Ga)As/GaAs quantum wells

Magnetooptical investigation of exciton transitions in high-quality quantum wells of an (In, Ga)As/GaAs heterosystem has been carried out. Investigation of transmission of free-hanging samples detached from the substrate in the magnetic fields of up to 12 T revealed a rich fine structure associated with various heavy-hole and light-hole exciton transitions. In particular, transitions from the excited states of light holes localized in a Coulomb potential produced by an electron along the heterojunction axis (a Coulomb well) have been detected. Taking into account consistently stresses, formation of Landau levels, the binding energies of excitons (diamagnetic excitons), and the effect of a Coulomb well, we have succeeded to describe the experimental results with the use of a self-consistent variational procedure. As a result, new features in the structure of optical transitions have been explained and the effective masses of electrons and holes of excitons formed by both heavy and light holes have been determined with a high accuracy.     

Weak localization in Al0.25Ga0.75As/In0.2Ga0.8As/GaAs wires

The phase coherence length L_Ø, its temperature dependence and the spin-orbit scattering length L_SO in Al_0.25Ga_0.75As/In_0.2Ga_0.8As/GaAs wires fabricated by electron-beam lithography and CH₄/H₂ Reactive Ion Etching (RIE), were extracted by fitting a 1-dimensional weak localization theory to two-terminal measurements in the temperature range between 2 K and 50 K. The scattering mechanism was found to be Nyquist (electron-electron collisions with small energy transfer).