α-Al_2O_3介孔材料导热特性的模拟

本文针对α-Al2O3有序介孔材料的导热特性开展分子动力学模拟分析.提出了一种保证电中性的孔道结构构造方法;采用逆非平衡分子动力学方法(muller-plathe法),选取Matsui势为作用势,模拟计算了Al2O3介孔晶体材料在不同环境温度下沿孔道轴向方向的热导率;并借助全面实验分析法,设计了模拟条件,以考察孔径和孔隙率对热导率的影响.模拟结果显示:介孔Al2O3热导率先随温度的升高呈上升趋势,并在200—400 K之间取得极值;而后在400—1400 K范围内,热导率随温度的升高几乎呈线性下降.孔隙率一定时,随孔径增大,介孔Al2O3材料比表面积降低,界面散射的抑制作用减弱,使材料热导率略有上升;孔径一定时,随孔隙率上升,孔道壁面声子数减少,材料热导率下降明显;相对于孔径因素,材料孔隙率对声子导热影响更大.     

介孔二氧化硅双重孔隙的导热特性研究

介孔二氧化硅颗粒的双重孔隙分布特征对材料的导热性能具有显著影响。本文通过微观形态表征分析了介孔二氧化硅的复合孔道,并基于受限空间内的气体分子动力学理论,构建了双重孔隙结构的热导率关联模型。为了验证理论模型的合理性与准确性,采用瞬态热带法测量了介孔二氧化硅材料(MCM-41和SBA-15)在0～30 MPa和20～550℃的环境压力及温度变化下的有效热导率。实验测量结果表明,本文理论模型可以有效预测介孔二氧化硅颗粒热导率的变化规律。进一步根据模型分析可知,材料热导率随着环境温度及压力的升高而增长,表现出明显的正相关性,同时其微观结构的差异也是热导率变化的决定性因素。     

超声波对合成介孔材料Al-MCM-41的有序度的影响

在超声频率为20 kHz,电功率为500 W的超声波作用下,分别以Al（NO₃）₃和Al₂ （SO₄）₃做铝源合成了具有不同Si/Al比的Al-MCM-41。XRD结果显示,尽管超声波作用下,掺杂杂原子Al也要降低介孔材料的有序度,但其有序度降低的程度比普通水热法要小,超声波的辅助可以在同样反应时间内得到比普通水热法具有更高有序度的Al-MCM-41,即在掺杂过程中,超声波要比普通搅拌有利于介孔材料保持其骨架稳定性。此外考察了超声波作用时间对产品有序度和粒度的影响。     

镧掺杂的介孔分子筛的合成及其光学性能研究

以十六烷基三甲基溴化铵(CTAB)为表面活性剂,正硅酸乙酯(TEOS)为硅源,采用水热晶化法,合成了镧掺杂的MCM-41介孔分子筛。通过X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、透射电镜(TEM)、紫外-可见(UV-Vis)光谱等测试手段对其孔结构和镧原子的存在状态进行了表征。XRD和TEM结果表明,合成样品具有典型的二维六方有序介孔结构,样品的傅里叶变换红外光谱和紫外-可见光谱表明镧被成功的引入到介孔骨架中。     

介孔分子筛Al-MCM-41的合成与催化异构化性能

采用正硅酸乙酯(TEOS)为硅源,九水硝酸铝为铝源,十六烷基三甲基溴化胺(CTMABr)为模板剂,在室温条件下合成了介孔Al-MCM-41分子筛.通过XRD、N2等温吸附、SEM、FTIR等分析测试手段表征了分子筛的介孔结构和表面性质.结果表明所合成的分子筛有良好的介孔结构和较高的有序度,并且有较高的比表面积(达到816 m2·g-1)和窄的孔径分布.采用程序升温的焙烧方式、凝胶Al/Si比最大范围控制在0.06～0.13有利于合成高度有序的介孔Al-MCM-41分子筛.评价结果表明,所合成的Al-MCM-41分子筛对桥式四氢双环戊二烯(endo-TCD)异构化反应合成挂式异构体exo-TCD及金刚烷具有较高的催化活性和极高的选择性.     

MCM-41负载磷钨酸的制备与表征

以十六烷基三甲基溴化铵(CTAB)为表面活性剂,以正硅酸乙酯(TEOS)为硅源,采用水热合成法制备了介孔分子筛MCM-41,并利用浸渍法将磷钨酸(HPW)负载在MCM-41分子筛上,得到HPW/MCM-41催化剂f采用X射线衍射、傅里叶变换红外光谱、透射电镜等手段对负载型催化剂进行了表征.结果表明,磷钨酸负载到MCM-...     

基于微拉曼光谱技术的氧化介孔硅热导率研究

利用基于有效介质理论的介孔硅传热机理，提出一个用于分析氧化介孔硅热导率的理论模型，对影响氧化介孔硅有效热导率的因素进行了理论分析，得出用于计算氧化介孔硅有效热导率的计算公式. 采用双槽电化学腐蚀法制备介孔硅，利用微拉曼光谱技术研究了氧化介孔硅热导率随所制备介孔硅孔隙率的变化规律，比较了经不同温度处理的氧化介孔硅的导热性能差异. 孔隙率为60%，73.4%和78.8%的所制备介孔硅经300℃氧化处理后，其热导率值为8.625W/(m·K)，3.846W/(m·K)和1.817W/(m·K)；孔隙率为73.4     

基于微拉曼光谱技术的氧化介孔硅热导率研究

利用基于有效介质理论的介孔硅传热机理,提出一个用于分析氧化介孔硅热导率的理论模型,对影响氧化介孔硅有效热导率的因素进行了理论分析,得出用于计算氧化介孔硅有效热导率的计算公式. 采用双槽电化学腐蚀法制备介孔硅,利用微拉曼光谱技术研究了氧化介孔硅热导率随所制备介孔硅孔隙率的变化规律,比较了经不同温度处理的氧化介孔硅的导热性能差异. 孔隙率为60%,73.4%和78.8%的所制备介孔硅经300℃氧化处理后,其热导率值为8.625W/(m·K),3.846W/(m·K)和1.817W/(m·K);孔隙率为73.4 关键词： 理论模型 氧化介孔硅 微拉曼光谱 有效热导率     

乙烷在中孔分子筛MCM-41中吸附的计算机分子模拟

采用计算机模拟方法研究不同温度下乙烷在不同孔径的MCM-41中的吸附.其中乙烷分子采用两个LJ中心的势模型表征，乙烷分子与MCM-41孔壁的相互作用采用一个连续的势模型表示.除考察了温度、孔径对吸附量的影响外，还研究这些量对乙烷分子在孔中的甲基和质心的分布，以及它们对乙烷分子在孔中的排列方向的影响.GCMC模拟结果发现，在180K和300K时壁面处都有较多的乙烷分子倾向于沿着壁面排列，同时在180K时其余的流体分子倾向于垂直于壁面排列，而在300K时其余的分子并不像在180K时一样倾向于垂直于壁面排列.模拟结果还表明，除壁面附近外，即使是在180K的较低温度下，乙烷分子的排列也是混乱和无序的.     

介孔碳材料对蛋白质的吸附行为

用紫外分光光度法,找出介孔碳材料对蛋白质的最佳吸附条件,并测定出该介孔碳材料对溶菌酶的最大吸附量。主要从3方面研究介孔碳材料对蛋白质吸附行为的影响。分别是介孔碳材料对蛋白质吸附行为随接触时间的变化产生的影响,pH值的改变对介孔碳材料吸附蛋白质行为的影响,以及介孔碳材料的量的改变对蛋白质吸附行为随接触时间的变化产生的影响。结果表明,当溶菌酶溶液的初始浓度为210μm ol/L,pH值为11.0,接触时间为96h时介孔碳材料对蛋白质即可达到吸附饱和。该介孔碳材料在最佳条件下对溶菌酶的最大吸附量为27.32μm ol/g,表现出优越的溶菌酶吸附性能。     

Rapid sonochemical synthesis of MCM-41 type benzene-bridged periodic mesoporous organosilicas

Benzene-bridged periodic mesoporous organosilicas (PMOs) with the MCM-41 were synthesized by a rapid sonochemical process via co-condensation of tetraethoxysilane (TEOS) and 1,4-bis(triethoxysilyl) benzene (BTEB) under basic conditions within a few minutes using cetyltrimethylammoniumbromide (CTMABr) as a structure-directing agent. The molar ratio of the silicon precursors and the synthesis time were varied in order to investigate their influence on the structural ordering of the materials. The characteristics of the materials were evaluated by X-ray diffraction (XRD), N₂-sorption, transmission electron microscopy (TEM) and solid-state NMR spectroscopy. The resultant materials exhibited well-ordered hexagonal mesostructures with surface areas in the range of 602–1237 m²/g, pore volumes of 0.37–0.68 cm³/g, and pore diameters in the range of 2.5–3.5 nm. Two dimensional ²⁹Si{¹H} heteronuclear correlation (HETCOR) NMR spectra confirmed the formation of a single mesophase with various Q (from TEOS) and T (from BTEB) silicon species located randomly within the pore walls due to the co-condensation of BTEB and TEOS, which excluded the possibility of formation of island or two separate phases within such a short synthesis time. The prime advantage of the present synthesis route is that it can effectively reduce the total synthesis time from days to a few minutes, much shorter than the conventional benzene-bridged PMOs synthesis methods.     

Thermal conductivity of a kind of mesoporous silica SBA-15

Mesoporous silica SBA-15 consists of uniform hexagonal, unconnected cylindrical channels with diameters that can be tuned within a range of 1.5 nm-30 nm, and is thought to have a special thermal conductivity. The theoretical investigation of the shell thermal conductivity of the mesoporous silica is performed in the relaxation time approximation in this paper and an available one-dimensional heat transfer model is used to predict the effective thermal conductivity （ETC） of the mesoporous silica. The experimental result of the ETC is also presented for comparison. The shell thermal conductivity of the mesoporous silica decreases with mesochannel radius increasing or wall thickness decreasing, but does not strictly decrease with porosity increasing. The thermal radiation possibly plays a primary role in heat transfer at the large porosity scale. The predicted ETC of SBA-15 with only conduction considered is quite low at the large porosity, even lower than the thermal conductivity of the silica aerogels. To realize it, doping carbon or other matters which can strongly absorb infrared light into SBA-15 is a possible way.     

Effect of reaction parameters on the growth of MWCNTs using mesoporous Sb/MCM-41 by chemical vapour deposition

Mesoporous Si-MCM-41 molecular sieve was synthesized hydrothermally and different wt.% of Sb (1.0, 2.0, 3.0, 5.0, 10.0, 15.0 and 20.0) was loaded on it by wet impregnation method. The Sb/MCM-41 materials were characterized by various physico-chemical techniques such as XRD, TGA and TEM. The TEM image showed a honeycomb structure of the host material. They were used as catalytic templates for the growth of MWCNTs by CVD method with different temperatures at 700, 800, 900 and 1000 °C using acetylene as a carbon precursor. The reaction temperature was optimized for the better formation of MWCNTs and they were purified and then characterized by XRD, SEM, HR-TEM and Raman spectroscopy techniques. The formation of MWCNTs with diameter in the range of 4−6 nm was observed from HR-TEM. The good thermal stability and high productivity of catalyst observed in this study revealed that the 2 wt.% Sb loaded MCM-41 could be a promising support for the catalytic synthesis of MWCNTs at 800 °C by CVD method.     

ZnO/MCM-41复合材料的制备及其光谱性质

以硅酸钠(NaSiO3·9H2O)为硅源,三甲基十六烷基溴化铵(CTAB)为模板剂在碱性条件下水热合成介孔分子筛MCM-41,然后以其为主体,采用锌盐浸渍-灼烧的方法.在介孔分子筛MCM-41上负载了氧化锌(ZnO)纳米微粒,并通过扫描电子显微镜,红外光谱(1R).紫外可见吸收光谱(UV-Vis),N2-吸附脱附和荧光光谱等手段对产品进行了系列表征.结果表明,分子筛平均直径约为1.7μm,对不同温度下灼烧后得到的ZnO/MCM-41组装体的光谱性质进行研究表明介孔分子筛MCM-41的尺寸所限,制备出的ZnO粒子粒径小于2 nm.量子尺寸效应使得ZnO/MCM-41组装体中的ZnO纳米粒子的紫外可见吸收光谱及荧光光谱均发生蓝移.通过红外光谱分析得知ZnO负载到MCM-41上并没有改变介孔分子筛原有的骨架结构.     

功能化单壁碳纳米管的热导率

采用基于BrennerⅡ势的非平衡态分子动力学方法,模拟研究了300K温度下经氢化学修饰的(10,0)单壁碳纳米管的热导率.研究显示功能化后碳管的热导率有明显减小,当有一列碳原子被氢化后（功能化程度为5%）,碳管的热导率减小了大约1/3,为了进一步解释这种功能化对碳纳米管热导率的影响,计算了不同功能化程度下碳纳米管的声子谱.     

Iron Uniform-Size Nanoparticles Dispersed on MCM-41 Used as Hydrocarbon Synthesis Catalyst

We have synthesized mesoporous MCM-41 and have used it as a support for iron particles to be employed as a catalyst in the Fischer–Tropsch reaction. The solids were characterized by Mössbauer spectroscopy, X-ray diffraction, BET, TGA, CO chemisorption and volumetric oxidation. Although the catalyst showed a high CO conversion when it was used in the hydrocarbon synthesis from CO and H₂ (14.3% at 1 h of reaction time) mainly methane was formed. The high methane production is likely related to the very small size of the metal particles obtained. We suggest some ways to improve the selectivity.     

功能化单壁碳纳米管的热导率

采用基于BrennerⅡ势的非平衡态分子动力学方法,模拟研究了300K温度下经氢化学修饰的(10,0)单壁碳纳米管的热导率.研究显示功能化后碳管的热导率有明显减小,当有一列碳原子被氢化后（功能化程度为5%）,碳管的热导率减小了大约1/3,为了进一步解释这种功能化对碳纳米管热导率的影响,计算了不同功能化程度下碳纳米管的声子谱.     

Synthesis and characterization of ionic liquid-functionalized alumino-silicate MCM-41 hybrid mesoporous materials

Ionic liquid-functionalized alumino-silicate MCM-41 hybrid mesoporous materials have been synthesized with two-step approach, by means of in situ skeleton doping with aluminium and post surface grafting with N-methylimidazole ionic liquid groups. The samples were characterized by X-ray diffraction (XRD), high resolution transmission electron microscope (HRTEM), N₂ adsorption-desorption, Fourier transform infrared (FTIR) spectra, ²⁷Al and ¹³C MAS NMR spectra and temperature-programmed desorption (TPD) of NH₃. The results indicated that the bifunctionalized MCM-41 possessed ordered mesostructure. Aluminium was efficiently introduced into the framework of the mesostructure, generating Lewis and Brönsted acid sites. N-methylimidazole ionic liquid groups were covalently grafted onto the surface of mesoporous materials. The as-synthesized bifunctional MCM-41 showed good catalytic performance in the coupling reaction of CO₂ and propylene oxide.     

荧光光谱法研究左氧氟沙星与MCM-41的相互作用

采用微波辅助水热法制备介孔分子筛MCM-41,并用浸渍法将左氧氟沙星(LVFX)组装在MCM-41均一的六方形孔道中,制备出新型载药复合物LVFX/MCM-41。用粉末X射线衍射(XRD)、低温氮吸附、傅里叶变换红外光谱(FTIR)及差热-热重(TGA-DTA)分析对MCM-41以及LVFX/ MCM-41复合物进行表征,合成的介孔分子筛MCM-41的孔径为2.382 nm,比表面积为1 015 m2·g-1。对MCM-41、LVFX/MCM-41、LVFX(固态)及LVFX(溶液)的荧光光谱研究结果显示,LVFX/MCM-41的荧光光谱比组装前发生明显红移,表明MCM-41孔道内表面的羟基和LVFX形成氢键,羟基上的电子云向LVFX分子上的吸电子基团转移;同时MCM-41和LVFX之间形成新环,使电子云能在更大的环上移动,药物分子的共轭体系扩大,荧光光谱峰红移。MCM-41与左氧氟沙星之间强的相互作用为研发以MCM-41为载体的新型释药系统提供了理论依据。