Cr2O3/C@TiO2核壳型复合材料的设计合成及其光催化产氢性能

随着社会经济的快速发展,能源危机和环境污染问题成为世界各国关注的焦点.通过光催化剂将太阳能用于污染物降解、分解水产氢、CO2还原及有机物合成等领域,是解决上述问题的理想途径.过渡金属氧化物TiO2因其稳定性高、催化活性好、制备简单等优点,被认为是最理想的光催化材料.然而,TiO2带隙较宽、光响应范围窄、光量子效率低等缺点限制了其实际应用.将碳或Cr2O3与TiO2结合形成复合结构已被证明可以有效提升其光催化性能.另一方面,金属离子的掺杂可以有效提高氧化钛的可见光响应.本文利用具有高比表面积的金属有机骨架材料MIL-101(Cr)纳米材料作为模板、镉源和碳源,首先在MIL-101(Cr)表面可控生长TiO2纳米颗粒,获得MIL-101(Cr)@TiO2复合结构;然后在氮气保护下碳化形成Cr2O3/C@TiO2核壳型复合材料.碳化后,制备的复合材料具有模板的八面体形貌和高比表面积,MIL-101(Cr)中的Cr元素一部分会形成Cr2O3,一部分会掺杂到TiO2中,使得TiO2的吸收边红移.此外,Cr2O3/C@TiO2中的C有利于光的吸收和载流子的分离.这种独特的纳米结构赋予Cr2O3/C@TiO2复合材料优异的光催化性能.在300 W氙灯照射下,该复合材料光解水产氢的速率为446μmol h?1 g?1,约为纯TiO2的4倍.在可见光照射下,Cr2O3/C@TiO2分解水产氢的速率为25.5μmol h?1 g?1.将获得的粉体催化剂制备成光电极发现,Cr2O3/C@TiO2在全幅光照射下的光电流密度在0.4 V(vs.Ag/AgCl)下达到2.3 mA/cm2,约为纯TiO2的3.5倍.Cr2O3/C@TiO2光催化产氢活性的提高一方面是由于Cr掺杂到TiO2中使得其具有可见光响应,另一方面MIL-101碳化获得的Cr2O3/C有效促进了光生载流子的分离.     

Cr2O3/C@TiO2核壳型复合材料的设计合成及其光催化产氢性能

随着社会经济的快速发展,能源危机和环境污染问题成为世界各国关注的焦点.通过光催化剂将太阳能用于污染物降解、分解水产氢、CO2还原及有机物合成等领域,是解决上述问题的理想途径.过渡金属氧化物TiO2因其稳定性高、催化活性好、制备简单等优点,被认为是最理想的光催化材料.然而,TiO2带隙较宽、光响应范围窄、光量子效率低等缺点限制了其实际应用.将碳或Cr2O3与TiO2结合形成复合结构已被证明可以有效提升其光催化性能.另一方面,金属离子的掺杂可以有效提高氧化钛的可见光响应.本文利用具有高比表面积的金属有机骨架材料MIL-101(Cr)纳米材料作为模板、镉源和碳源,首先在MIL-101(Cr)表面可控生长TiO2纳米颗粒,获得MIL-101(Cr)@TiO2复合结构;然后在氮气保护下碳化形成Cr2O3/C@TiO2核壳型复合材料.碳化后,制备的复合材料具有模板的八面体形貌和高比表面积,MIL-101(Cr)中的Cr元素一部分会形成Cr2O3,一部分会掺杂到TiO2中,使得TiO2的吸收边红移.此外,Cr2O3/C@TiO2中的C有利于光的吸收和载流子的分离.这种独特的纳米结构赋予Cr2O3/C@TiO2复合材料优异的光催化性能.在300 W氙灯照射下,该复合材料光解水产氢的速率为446μmol h?1 g?1,约为纯TiO2的4倍.在可见光照射下,Cr2O3/C@TiO2分解水产氢的速率为25.5μmol h?1 g?1.将获得的粉体催化剂制备成光电极发现,Cr2O3/C@TiO2在全幅光照射下的光电流密度在0.4 V(vs.Ag/AgCl)下达到2.3 mA/cm2,约为纯TiO2的3.5倍.Cr2O3/C@TiO2光催化产氢活性的提高一方面是由于Cr掺杂到TiO2中使得其具有可见光响应,另一方面MIL-101碳化获得的Cr2O3/C有效促进了光生载流子的分离.     

Photoassisted NO reduction with NH3 over TiO2 photocatalyst

Photoassisted selective catalytic reduction of NO with ammonia (photo-SCR) at low temperature over irradiated TiO2 in a flow reactor was confirmed to proceed efficiently and the adsorbed ammonia reacted with NO under irradiation of TiO2.     

Influence of long-term aqueous exposure on surface properties of plasma-sprayed oxides Cr2O3 and Cr2O3-25 wt% TiO2

The influence of water exposure on the surface properties of plasma-sprayed Cr(2)O(3) and Cr(2)O(3)-25 wt% TiO(2) was studied. It was shown that both plasma-sprayed materials contained Cr(VI) hydrous oxide phases, which dissolved rapidly at the beginning of water exposure. The dissolution continued slowly during the whole water exposure time. The Cr(VI) dissolution was accompanied by a rapid increase in surface IEP value. Both Cr(2)O(3) and Cr(2)O(3)-25 wt% TiO(2) showed similar dissolution, zeta potential, and surface oxidation states. Thus the addition of TiO(2) did not influence the surface properties of the plasma-sprayed Cr(2)O(3).     

Polymerization of aniline derivatives by K2Cr2O7 and production of Cr2O3 nanoparticles

Oxidative polymerization of aniline, anthranilic acid, and aniline‐co‐anthranilic acid by potassium dichromate Cr(VI) as an oxidant in acidic medium was investigated. In this study, the polymerization process of aniline, o‐anthranilic acid as well as aniline/o‐anthranlic acid using K₂Cr₂O₇ produced, coordinated Cr(III)/polyaniline (PANI), Cr(III)/polyanthranilic acid (PAA) and Cr(III)/poly aniline‐co‐anthranilic acid (PANAA). The mechanism of polymerization reaction in the presence of dichromate was hypothesized. The precursor chromium doped polymers were characterized by TGA, FT‐IR, UV‐visible, XRD analyses. Cr₂O₃ nanoparticles size were determined using TEM analysis. The calcinations process of synthesized chromium doped PANI, PAA and PANAA yields Cr₂O₃ nanoparticles 26%, 31%, and 34% wt. respectively. Rhombohedral phase of Cr₂O₃ particles in the range from 33 to 61 nm was produced from chromium/polyanthranilic acid (PAA) and chromium/poly(aniline‐co‐anthranilic acid) PANAA. UV‐ visible analysis showed that optical band gaps (E_g) of doped poly aniline and its derivatives are in the range from1.55 to 1.80 using Tacu's law. The band gap values reveal that the doped chromium emeraldine base can be used as semiconductor materials. Copyright © 2016 John Wiley & Sons, Ltd.     

非晶TiO2修饰CuBi2O4光阴极增强其光电化学产氢活性

光催化作为太阳能利用领域的研究热点引起了广泛的关注.其中,光电化学技术能够通过分解水提供清洁的氢能源,因此被认为是一种潜在的新能源制造方式.在光电化学分解水产氢的过程中,最重要的是高效光电极的制备.一系列n型半导体材料已被广泛地报道并用作光阳极,如BiVO4,ZnO,Fe2O3等.然而对于光阴极材料,其可选择性则较少.CuBi2O4是一种天然矿物,具有廉价易得以及化学性质稳定的特性,而且是一种p型半导体材料,因此能够用于制备光阴极;另外因为其强的可见光响应(1.70 eV),所以具有广泛的应用前景.目前对于CuBi2O4光阴极研究主要集中在合成和理论计算方面,而对于如何促进界面处的载流子分离研究较少.本文通过一种简单的电沉积方法成功制备出CuBi2O4光阴极,然后利用非晶TiO2和助催化剂Pt进行修饰后将其用于光电化学产氢.由于形成了CuBi2O4/TiO2 p-n结,因此其光阴极活性得到增强.新的Pt/TiO2/CuBi2O4光阴极在0.60 V偏压处的光电流为0.35 mA/cm2,其数值约为Pt/CuBi2O4光阴极的两倍.XRD结果表明,我们制备的CuBi2O4为纯相且结晶性较好,其表面修饰的TiO2为非晶相的.SEM结果表明,CuBi2O4电极层由100-150 nm的颗粒构成.紫外-可见吸收光谱表明,制备的CuBi2O4光电极拥有良好的可见光吸收性质,而且TiO2修饰未对CuBi2O4的光吸收产生明显的影响.XPS结果表明,修饰TiO2并未对CuBi2O4电极造成成分上的破坏.光电化学测试表明,修饰TiO2层厚度和结晶性会影响光电极的最终活性.修饰四层TiO2和退火200 oC的样品具有最好的活性.另外稳定性测试也表明,修饰非晶TiO2的CuBi2O4光阴极具有良好的稳定性.在IPCE测试中,Pt/TiO2/CuBi2O4光阴极在其光响应范围内均比Pt/CuBi2O4光阴极表现出更高的效率.阻抗结果测试中Pt/TiO2/CuBi2O4光阴极具有更小的阻抗,这表明其载流子传输更加高效.在Mott-Shetty测试中,Pt/TiO2/CuBi2O4和Pt/CuBi2O4光阴极都表现出p型半导体性质,但是Pt/TiO2/CuBi2O4具有更负的平带电位,这表明修饰的TiO2仍具有n型半导体材料的特性,并与p型的CuBi2O4形成p-n结,从而促进了载流子分离效率.     

Artificial photochemical nitrogen cycle to produce nitrogen and hydrogen from ammonia by platinized TiO2 and its application to a photofuel cell

Photochemical artificial nitrogen cycle was reported to produce dinitrogen and dihydrogen by photodecomposing ammonia with platinized TiO2, and its application to a photofuel cell with a nanoporous TiO2 film electrode, a new concept of a fuel cell to photochemically produce electricity and H2 from ammonia, was proposed.     

锂离子电池用Cr2O3/TiO2复合材料的电化学性能

采用高温固相反应法合成了Cr₂O₃/TiO₂复合材料, 运用X射线衍射(XRD)、扫描电子显微镜(SEM)、充放电测试、循环伏安(CV)、电化学阻抗谱(EIS)等对其结构、形貌和电化学性能进行了表征. 研究结果表明: TiO₂掺杂能够显著改善Cr₂O₃的充放电循环性能, Cr₂O₃/TiO₂复合材料在充放电循环22周后仍有454 mAh·g^-1的可逆循环容量, 容量保持率达到了73.6%, 主要归因于TiO₂掺杂能够显著提高Cr₂O₃的电导率. Cr₂O₃/TiO₂复合材料首次放电过程中由于电极体积膨胀导致的固体电解质相界面(SEI)膜迅速增厚和活性材料电导率的降低可能是其首次充放电过程中存在较大不可逆容量和循环容量衰减的重要原因.     

C/Cr2O3/TiO2复合材料的制备及其光催化性能研究

本文以制革含铬革屑为原材料,基于矿物鞣剂复鞣的原理,将Ti(IV)均匀、稳定地负载到含铬革屑上,在氮气氛围下,经高温热解制备得到C/Cr₂O₃/TiO₂光催化剂,并研究了其对四环素(TC)的光催化降解效果及机理。结果表明,C/Cr₂O₃/TiO₂光催化剂具有明显的介孔结构,比表面积较大,为277.47 m²·g^-1,Cr₂O₃和TiO₂已实现复合并负载在生物炭(C)上。通过光催化降解发现,在模拟自然光照下,当催化剂用量为0.04 g,TC初始浓度为50 mg·L^-1,溶液pH为2时,TC的去除率可高达99.99%。结合自由基捕获实验发现,C/Cr₂O₃/TiO₂光催化剂对TC的降解作用主要依靠反应体系中产生的大量·O₂^-,·OH和h⁺。     

Characterization of La-promoted Ni/Al2O3 catalysts for hydrogen production from glycerol dry reforming

In the current paper, dry (CO₂)-reforming of glycerol, a new reforming route, was carried out over alumina (Al₂O₃)-supported, non-promoted and lanthanum-promoted nickel (Ni) catalysts. Both sets of catalysts were synthesized via a wet co-impregnation procedure. Physicochemical characterization of the catalysts showed that the promoted catalyst possessed smaller metal crystallite size, hence higher metal dispersion compared to the virgin Ni/Al₂O₃ catalyst. This was also corroborated by the surface images captured by the FESEM analysis. From temperature-programmed calcination analysis, the derivative weight profiles revealed two peaks, which represent a water elimination peak at a temperature range of 373 to 473 K followed by nickel nitrate decomposition from 473 to 573 K. In addition, BET surface area measurements gave 85.0 m²·g⁻¹ for the non-promoted Ni catalyst, whilst the promoted catalysts showed an average of 1% to 6% improvement depending on the La loadings. Significantly, reaction studies at 873 K showed that glycerol dry reforming successfully produced H₂. The 2%La-Ni/Al₂O₃ catalyst, which possessed the largest BET surface area, gave an optimum H₂ generation (9.70%) at a glycerol conversion of 24.5%.     

TiO_2-Al_2O_3载体的制备方法对其负载的磷化镍催化剂加氢脱氮反应性能的影响

采用共沉淀法和原位溶胶-凝胶法制备了TiO2-Al2O3复合载体,其负载的磷化镍催化剂采用等体积浸渍法和H2原位还原法制备.通过N2吸附(BET)、X射线衍射(XRD)、透射电镜(TEM)、程序升温还原(TPR),X射线光电子能谱(XPS)和等离子体发射光谱(ICP-AES)表征技术对催化剂进行了表征,并通过喹啉的加氢脱氮反应评价了催化剂的加氢脱氮性能.结果表明,原位溶胶-凝胶法制成的复合载体基本保留了原有的γ-Al2O3的孔特征,具有较大的比表面积和较宽的孔分布,TiO2主要以表面富集的形式分散在管状的γ-Al2O3表面,其负载的磷化镍催化剂还原后所形成的活性相为Ni2P和Ni12P5;而共沉淀法制成的复合载体比表面积较小,孔径分布更加集中,TiO2趋于在块状的Al2O3表面均匀分散,其负载的磷化镍催化剂具有更好的可还原性,还原后所形成的活性相为Ni2P.不同的载体制备方法和不同的钛铝比对催化剂加氢脱氮性能影响较大,当n(Ti)/n(Al)=1/8时,共沉淀法载体负载的催化剂表现出最佳的加氢脱氮性能,在340℃,3 MPa,氢油体积比500,液时空速3 h-1的反应条件下,喹啉的脱氮率可以达到91.3%.     

3D flower-like heterostructured TiO2@Ni(OH)2 microspheres for solar photocatalytic hydrogen production

TiO₂@Ni(OH)₂ core-shell microspheres were synthesized by a facile strategy to obtain a perfect 3D flower-like nanostructure with well-arranged Ni(OH)₂ nanoflakes on the surfaces of TiO₂ microspheres; this arrangement led to a six-fold enhancement in photocatalytic hydrogen evolution. The unique p-n type heterostructure not only promotes the separation and transfer of photogenerated charge carriers significantly, but also offers more active sites for photocatalytic hydrogen production. A photocatalytic mechanism is proposed based on the results of electrochemical measurements and X-ray photoelectron spectroscopy.     

Sustained production of H2O2 on irradiated TiO2- fluoride systems

UV irradiation of fluorinated TiO(2) suspensions in water, in the presence of oxygen and a hole scavenger, leads to the production of H(2)O(2) with steady state concentration levels up to 1.3 millimolar; the H(2)O(2) formation rate follows the TiO(2) surface speciation, being maximum when the surface is completely covered by [triple bond]Ti-F groups; these results outline the importance of surface speciation on the photocatalytic process.     

Cr负载V2O5-WO3/TiO2催化剂的低温NH3-SCR脱硝活性

采用浸渍法制备了一系列不同Cr负载量的CrO_x-V₂O₅-WO₃/TiO₂催化剂, 研究了Cr改性对该催化剂脱硝活性及抗硫性能的影响. 结果表明, Cr的引入使V₂O₅-WO₃/TiO₂催化剂的低温NO_x去除效果和抗硫性能显著提升. Cr的负载量为3%(以Cr₂O₃计算质量分数)时, 催化剂具有最佳的低温脱硝活性和N₂选择性. 结构表征结果表明, 改性催化剂中Cr元素主要以Cr³⁺形式存在, Cr的引入使催化剂的氧化性能明显提升, 并使表面弱酸位点、 强酸位点和催化剂表面吸附氧数量增多. XPS分析结果表明, Cr能使催化剂中V⁵⁺/V⁴⁺比例降低, 促进催化剂中自由电子的迁移. In situ DRIFTs表征结果显示, Cr的引入能促进NO与吸附在Brönsted酸位点上的NH₃在低温条件下反应, 从而使催化剂具有更好的低温脱硝活性. UV-Vis光谱分析结果表明, CrO_x负载量提高会显著增加高价态Cr的烧结聚集. 同时, 提出了一种选择性催化还原(SCR)反应中Cr-V协同催化的机理.     

Initial Studies on the Oxide System Cr2O3–Sb2O4

Differential thermal analysis (DTA) and X-ray diffraction (XRD) were utilized to study the phase equilibrium established in the subsolidus area of the system Cr₂ O₃ –Sb₂ O₄ . It was found that the components of the title system interact in ambient air to produce CrSbO₄ . The compound is stable up to ~1380°C, at which temperature it starts to decompose. This revised version was published online in August 2006 with corrections to the Cover Date.     

Spektroskopische Untersuchungen und Phasenbeziehungen im System Li2O−Al2O3−Cr2O3

Zusammenfassung Aus Li₂CO₃ und (Al_1–x Cr _x )₂O₃ wurde durch Festkörperreaktionen die Mischkristallreihe LiAl_1–x Cr _x O₂ hergestellt. Die thermische Stabilität der mikrokristallinen Substanzen (-NaFeO₂-Typ, Raumgruppe R3m) wurde röntgenographisch verfolgt. Die diffusen Reflexionsspektren (12 bis 30 kK, 25°C) wurden mit dem Modell der erweiterten Kristallfeldtheorie ausgewertet. Die durch Multiphononen-Struktur charakterisierten spin-erlaubten Banden ergeben für kubische MikrosymmetrieDq- undRacah-B-Werte, die im Gegensatz zur Rubinreihe nur wenig von Cr-Gehalt abhängen.Dq beruht zum Teil auf dem Einfluß von zweitnächsten Li⁺-Nachbarn, wodurch die effektive Ladung der Sauerstoff-Liganden in der Bindung größer ist. Die breite spin-verbotene Bande bei 15 kK deutet auf eine Magnon-Satellitenstruktur durch antiferromagnetische Ordnung hin.

---

Optical studies and phase relations in the system Li₂O–Al₂O₃–Cr₂O₃

The series LiAl_1–x Cr _x O₂ was prepared by solid state reactions with Li₂CO₃ and (Al_1–x Cr _x )₂O₃. The thermal stability of the microcrystalline samples (-NaFeO₂ type, space group R3m) was controlled by X-ray methods. The diffuse reflectance spectra at 25 °C in the region from 12 to 30 kK were analyzed by the extended crystal field theory. From the spin-allowed peaks characterized by a multiphonon structureDq-andRacah-B-values were obtained for cubic site symmetry (neglecting trigonal distortions and spin-orbit effects) that are only slightly dependent on the Cr-content, in contrast to the ruby series.Dq is partly due to the influence of the secondnearest Li⁺-neighbours leading to a greater effective charge of the oxygen ligands in the bond. The broad spin-forbidden peak at 15 kK points to a magnon satellite structure caused by antiferromagnetic ordering.

---

---

Mit 1 Abbildung