AlGaN/GaN高电子迁移率器件外部边缘电容的物理模型

AlGaN/GaN HEMT外部边缘电容Cofd是由栅极垂直侧壁与二维电子气水平壁之间的电场构成的等效电容.本文基于保角映射法对Cofd进行物理建模,考虑沟道长度调制效应,研究外部偏置、阈值电压漂移和温度变化对Cofd的影响:随着漏源偏压从零开始增加,Cofd先保持不变再开始衰减,其衰减速率随栅源偏压的增加而减缓;AlGaN势垒层中施主杂质浓度的减小和Al组分的减小都可引起阈值电压的正向漂移,正向阈值漂移会加强沟道长度调制效应对Cofd的影响,导致Cofd呈线性衰减.在大漏极偏压工作情况下,Cofd对器件工作温度的变化更加敏感.     

中子辐照对AlGaN/GaN高电子迁移率晶体管器件电特性的影响

本文采用能量为1 MeV的中子对SiN钝化的AlGaN/GaN HEMT(高电子迁移率晶体管)器件进行了最高注量为1015cm-2的辐照.实验发现:当注量小于1014cm-2时,器件特性退化很小,其中栅电流有轻微变化(正向栅电流IF增加,反向栅电流IR减小),随着中子注量上升,IR迅速降低.而当注量达到1015cm-2时,在膝点电压附近,器件跨导有所下降.此外,中子辐照后,器件欧姆接触的方块电阻退化很小,而肖特基特性退化却相对明显.通过分析发现辐照在SiN钝化层中引入的感生缺陷引起了膝点电压附近漏电流和反向栅泄漏电流的减小.以上结果也表明,SiN钝化可以有效地抑制中子辐照感生表面态电荷,从而屏蔽了绝大部分的中子辐照影响.这也证明SiN钝化的AlGaN/GaN HEMT器件很适合在太空等需要抗位移损伤的环境中应用.     

具有部分本征GaN帽层新型AlGaN/GaN高电子迁移率晶体管特性分析

为了优化传统Al GaN/GaN高电子迁移率晶体管(high electron mobility transistors,HEMTs)器件的表面电场,提高击穿电压,本文提出了一种具有部分本征GaN帽层的新型Al GaN/GaN HEMTs器件结构.新型结构通过在Al GaN势垒层顶部、栅电极到漏电极的漂移区之间引入部分本征GaN帽层,由于本征GaN帽层和Al GaN势垒层界面处的极化效应,降低了沟道二维电子气(two dimensional electron gas,2DEG)的浓度,形成了栅边缘低浓度2DEG区域,使得沟道2DEG浓度分区,由均匀分布变为阶梯分布.通过调制沟道2DEG的浓度分布,从而调制了Al GaN/GaN HEMTs器件的表面电场.利用电场调制效应,产生了新的电场峰,且有效降低了栅边缘的高峰电场,Al GaN/GaN HEMTs器件的表面电场分布更加均匀.利用ISE-TCAD软件仿真分析得出:通过设计一定厚度和长度的本征GaN帽层,Al GaN/GaN HEMTs器件的击穿电压从传统结构的427 V提高到新型结构的960 V.由于沟道2DEG浓度减小,沟道电阻增加,使得新型Al GaN/GaN HEMTs器件的最大输出电流减小了9.2%,截止频率几乎保持不变,而最大振荡频率提高了12%.     

AlGaN/GaN高电子迁移率晶体管温度传感器特性

本文制作了基于无栅AlGaN/GaN高电子迁移率晶体管结构的温度传感器,并对其温度相关的电学特性进行了表征.实验测试了器件从50℃到400℃的变温电流-电压特性,研究了器件灵敏度随着器件沟道长宽比的变化,并研究了在300—500℃高温的空气和氮气中经过1 h恒温加热后器件的电学特性变化.理论与实验研究结果表明,随着器件沟道长宽比的增大,器件的灵敏度会随之上升;在固定电流0.01 A下,器件电压随温度变化的平均灵敏度为44.5 mV/℃.同时,稳定性实验显示器件具有较好的高温保持稳定性.     

AlGaN/AlN/GaN结构中二维电子气的输运特性

对使用金属有机物汽相沉积法生长的AlGaN/AlN/GaN结构进行的变温霍尔测量，测量结果指出在AlN/GaN界面处有二维电子气存在且迁移率和浓度在2K时分别达到了1.4×10⁴cm²·V^-1·s^-1和9.3×10¹²cm^-2，且在200K到2K范围内二维电子气的浓度基本不变，变磁场霍尔测量发现只有一种载流子(电子)参与导电.在2K温度下，观察到量子霍尔效应，Shubnikov-de Haas (SdH) 振荡在磁场约为3T时出现，证明了此结构呈现了典型的二维电子气行为.通过实验数据对二维电子气散射过程的半定量分析，推出量子散射时间为0.23ps，比以往报道的AlGaN/GaN结构中的散射时间长，说明引入AlN层可以有效减小合金散射，进一步的推断分析发现低温下以小角度散射占主导地位.     

半导体量子器件物理讲座 第二讲 高电子迁移率晶体管（HEMT）

文章从异质界面的三角势阱中二维电子气的形成入手,计算了二维电子气的量子化能级及其面电子密度,对HEMT器件材料结构参数的优化、器件的电荷控制模型I－V特性作了分析。     

生物分子膜门电极AlGaN/GaN高电子迁移率晶体管(HEMT)生物传感器研究

设计并制作了结构尺寸为毫米量级的AlGaN/GaN高电子迁移率晶体管(HEMT)生物传感器,采用数值分析的方法分析了器件传感区域长度与宽度比值及待测物调控二维电子气(2DEG)距离与感测信号之间的关系,给出了结构尺寸为毫米量级的AlGaN/GaN HEMT生物传感器的设计依据,以不同浓度的前列腺特异性抗原(PSA)为待测物,对制作的AlGaN/GaN HEMT生物传感器进行了初步测量,测试结果表明,在50 mV的电压下,毫米量级的AlGaN/GaN HEMT生物传感器的对PSA的探测极限低于0.1 pg/ml.实验表明毫米量级的AlGaN/GaN HEMT生物传感器具有灵敏度高,易于集成等优点,具备良好的应用前景.     

高温AlN插入层对AlGaN/GaN异质结材料和HEMTs器件电学特性的影响

研究了在GaN缓冲层中插入40 nm厚高温AlN层的GaN外延层和AlGaN/GaN异质结材料, AlN插入层可以增加GaN层的面内压应力并提高AlGaN/GaN高电子迁移率晶体管（HEMTs）的电学特性. 在精确测量布拉格衍射角的基础上定量计算了压应力的大小. 增加的压应力一方面通过增强GaN层的压电极化电场, 提高了AlGaN/GaN异质结二维电子气（2DEG）面密度, 另一方面使AlGaN势垒层对2DEG面密度产生的两方面影响相互抵消. 同时, 这种AlN插入层的采用降低了GaN与AlGaN层之间的 关键词： 高温AlN插入层 AlGaN/GaN异质结 二维电子气 应力     

3 MeV质子辐照对AlGaN/GaN高电子迁移率晶体管的影响

研究了AlGaN/GaN 高电子迁移率晶体管(HEMT)的质子辐照效应. 在3 MeV质子辐照下, 当辐照剂量达到1× 10¹⁵ protons/cm²时, 漏极饱和电流下降了20%, 最大跨导降低了5%. 随着剂量增加, 阈值电压向正向漂移, 栅泄露电流增加. 在相同辐照剂量下, 1.8 MeV质子辐照要比3 MeV质子辐照退化严重. 从SRIM软件仿真中得到不同能量质子在AlGaN/GaN异质结中的辐射损伤区, 以及在一定深度形成的空位密度. 结合变频C-V测试结果进行分析, 表明了质子辐照引入空位缺陷可能是AlGaN/GaN HEMT器件电学特性退化的主要原因.     

使用AlN/GaN超晶格势垒层生长高Al组分AlGaN/GaN HEMT结构

在蓝宝石衬底上生长了以AlN/GaN超晶格准AlGaN合金作为势垒的HEMT结构材料,并与传统AlGaN合金势垒样品进行了对比.在高Al组分(≥40%)情况下,超晶格势垒样品的表面形貌明显改进,电学性能特别是2DEG面电子浓度也有所改进.对超晶格势垒生长参数进行了初步优化,使得HEMT结构薄层电阻进一步降低,最后获得了251 Ω/□的薄层电阻. 关键词： AlGaN/GaN 结构 AlN/GaN超晶格 二维电子气 高电子迁移率晶体管     

The physical process analysis of the capacitance-voltage characteristics of AlGaN/AlN/GaN high electron mobility transistors

This paper deduces the expression of the Schottky contact capacitance of AlGaN/AlN/GaN high electron mobility transistors (HEMTs), which will help to understand the electron depleting process. Some material parameters related with capacitance-voltage profiling are given in the expression. Detailed analysis of the forward-biased capacitance has been carried on. The gate capacitance of undoped AlGaN/AlN/GaN HEMT will fall under forward bias. If a rising profile is obviously observed, the donor-like impurity or trap is possibly introduced in the barrier.     

High temperature characteristics of AlGaN/GaN high electron mobility transistors

Direct current (DC) and pulsed measurements are performed to determine the degradation mechanisms of AlGaN/GaN high electron mobility transistors (HEMTs) under high temperature. The degradation of the DC characteristics is mainly attributed to the reduction in the density and the mobility of the two-dimensional electron gas (2DEG). The pulsed measurements indicate that the trap assisted tunneling is the dominant gate leakage mechanism in the temperature range of interest. The traps in the barrier layer become active as the temperature increases, which is conducive to the electron tunneling between the gate and the channel. The enhancement of the tunneling results in the weakening of the current collapse effects, as the electrons trapped by the barrier traps can escape more easily at the higher temperature.     

High-field-induced electron detrapping in An AlGaN/GaN high electron mobility transistor

A step stress test is carried out to study the reliability characteristics of an AlGaN/GaN high electron mobility transistor(HEMT).An anomalous critical drain-to-gate voltage with a negative temperature coefficient is observed in the stress sequence,beyond which the HEMT device starts to recover from degradation induced by early lower voltage stress.While the performance degradation featuring the drain current slump stems from electron trapping in the surface or bulk states during low-to-medium bias stress,the recovery is attributed to high field induced electron detrapping.The carrier detrapping mechanism could be helpful for lessening the trapping-related performance degradation of a GaN-based HEMT.     

Fluorine-plasma treated AlGaN/GaN high electronic mobility transistors under off-state overdrive stress

Influences of off-state overdrive stress on the fluorine-plasma treated AlGaN/GaN high-electronic mobility transistors (HEMTs) are experimentally investigated. It is observed that the reverse leakage current between the gate and source decreases after the off-state stress, whereas the current between the gate and drain increases. By analyzing those changes of the reverse currents based on the Frenkel-Poole model, we realize that the ionization of fluorine ions occurs during the off-state stress. Furthermore, threshold voltage degradation is also observed after the off-state stress, but the degradations of AlGaN/GaN HEMTs treated with different F-plasma RF powers are different. By comparing the differences between those devices, we find that the F-ions incorporated in the GaN buffer layer play an important role in averting degradation. Lastly, suggestions to obtain a more stable fluorine-plasma treated AlGaN/GaN HEMT are put forwarded.     

Neutron irradiation effects on AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) were exposed to 1 MeV neutron irradiation at a neutron fluence of 1 × 10¹⁵ cm^-2. The dc characteristics of the devices, such as the drain saturation current and the maximum transconductance, decreased after neutron irradiation. The gate leakage currents increased obviously after neutron irradiation. However, the rf characteristics, such as the cut-off frequency and the maximum frequency, were hardly affected by neutron irradiation. The AlGaN/GaN heterojunctions have been employed for the better understanding of the degradation mechanism. It is shown in the Hall measurements and capacitance-voltage tests that the mobility and concentration of two-dimensional electron gas (2DEG) decreased after neutron irradiation. There was no evidence of the full-width at half-maximum of X-ray diffraction (XRD) rocking curve changing after irradiation, so the dislocation was not influenced by neutron irradiation. It is concluded that the point defects induced in AlGaN and GaN by neutron irradiation are the dominant mechanisms responsible for performance degradations of AlGaN/GaN HEMT devices.     

Direct-current and radio-frequency characteristics of passivated AlGaN/GaN/Si high electron mobility transistors

AlGaN/GaN/Si HEMTs grown by molecular beam epitaxy have been investigated using spectroscopy capacitance, direct and pulse current–voltage and small-signal microwave measurements. Passivation of the HEMT devices by SiO₂/SiN with NH₃ and N₂O pretreatments is made in order to reduce the trapping effects. As has been found from DLTS data, some of electron traps are eliminated after passivation. This has led to an improvement in the drain current. To describe the electron transport, we have developed a charge-control model by including the deep traps observed from DLTS experiments. The thermal and trapping effects have been, on the other hand, studied from a comparison between direct-current and pulsed conditions. As a result, a gate-lag and a drain-lag were revealed indicating the presence of deep lying centers in the gate-drain spacing. Finally, small-signal microwave results have shown that the radio-frequency parameters of the AlGaN/GaN/Si transistors are improved by SiO₂/SiN passivation and more increasingly with N₂O pretreatment.     

The degradation mechanism of an AlGaN/GaN high electron mobility transistor under step-stress

Step-stress experiments are performed in this paper to investigate the degradation mechanism of an AlGaN/GaN high electron mobility transistor(HEMT).It is found that the stress current shows a recoverable decrease during each voltage step and there is a critical voltage beyond which the stress current starts to increase sharply in our experiments.We postulate that defects may be randomly induced within the AlGaN barrier by the high electric field during each voltage step.But once the critical voltage is reached,the trap concentration will increase sharply due to the inverse piezoelectric effect.A leakage path may be introduced by excessive defect,and this may result in the permanent degradation of the AlGaN/GaN HEMT.