New Electrochemical Sensor of Prolonged Application for Metformin Determination Based on Hydrated Ruthenium Dioxide‐Carbon Black‐Nafion Modified Glassy Carbon Electrode

Metformin (MET) is an antidiabetic drug most commonly used in treatment of diabetes mellitus type 2 (T2D). Adsorptive stripping voltammetric method using carbon black – hydrated ruthenium dioxide – Nafion modified glassy carbon electrode (CB‐RuO₂‐Nafion GC electrode) have been developed for metformin determination in pharmaceutical formulations. By using ruthenium dioxide, electrode's lifespan was extended to at least 3 weeks (change of metrological parameters estimated as 3–4 %) what is an excellent result concerning other solutions previously described in the literature. Moreover the fabrication of the sensor is simple and fast. Deposition step was carried out at the potential 0 mV for 15 s. The best results were obtained in 0.05 M acetate buffer (pH 4.6). Important aspect was fixed MET : Cu(II) ratio equal to 1 : 8, otherwise linear dependence between register current and MET concentration could not be obtained. In addition, a significant improvement in the parameters of the calibration curve was obtained. Limit of detection was equal to 0.7 μM. Developed method was successfully applied in analysis of 2 pharmaceuticals products and in wastewater and river water. Accuracy of the method was estimated using recoveries, which were in the range 101–110 %. In order to adapt developed system into hydrodynamic conditions, amperometry in hydrodynamic transport conditions and flow injection analysis (FIA) measurements have been conducted. Conducted FIA measurements prove that developed method has potential for application in automized flow systems without frequent calibration.     

Fabrication of an Electrochemical L‐Cysteine Sensor Based on Graphene Nanosheets Decorated Manganese Oxide Nanocomposite Modified Glassy Carbon Electrode

The graphene nanosheets/manganese oxide nanoparticles modified glassy carbon electrode (GC/GNSs/MnOx) was simply prepared by casting a thin film of GNSs on the GC electrode surface, followed by performing electrodeposition of MnOx at applied constant potential. The GC/GNSs/MnOx modified electrode shows high catalytic activity toward oxidation of L ‐cysteine. Hydrodynamic amperometry determination of L ‐cysteine gave linear responses over a concentration range up to 120 µM with a detection limit of 75 nM and sensitivity of 27 nA µM^?1. The GC/GNSs/MnOx electrode appears to be a highly efficient platform for the development of sensitive, stable and reproducible L ‐cysteine electrochemical sensors.     

Electrochemical Detection of Steroid Hormones Using a Nickel‐Modified Glassy Carbon Electrode

This paper demonstrates the development of an analytical method for detecting steroid hormones by coupling HPLC to electrochemical detection, using a nickel‐modified glassy carbon electrode. The method was evaluated in terms of sensitivity, linear dynamic range, limit of detection, and response stability. The developed method exhibited good figures of merit for the steroid hormones studied with no evidence of electrode fouling. As an example, the limit of detection (S/N=3) for E3 was 0.10 µM and the response precision (n=5) was 0.6 %. The application of the method for the analysis of a real river water sample is demonstrated.     

Low Potential Detection of NADH at Titanium‐Containing MCM‐41 Modified Glassy Carbon Electrode

Titanium‐containing MCM‐41 (Ti‐MCM‐41) modified glassy carbon electrode (GCE) can exhibit an excellent electrocatalytic activity towards the oxidation of β‐Nicotinamide adenine dinucleotide (NADH). A dramatic decrease in the over‐voltage of NADH oxidation reaction is observed at 0.28 V (vs. SCE). The modified electrode is found to be stable and reproducible. The electrode shows a linear response for a wide range of 10–1200 μM NADH and the detection limit is 8.0 μM. Ti‐MCM‐41 mesoporous molecular sieves provide an efficient matrix for development of NADH biosensors and the prepared electrode not only can be used to detect the concentration of NADH in biochemical reaction, but also as the potential matrix of the construction of dehydrogenases biosensor.     

Electrochemical Detection of Alloxan on Reduced Graphene Oxide Modified Glassy Carbon Electrode

Alloxan is a toxic reagent that strongly induces the diabetes by destroying insulin‐producing β‐cells in the pancreas of living organisms. The reduction product of alloxan is dialuric acid, which is responsible for the intracellular generation of ROS to enhance the stress in living cells to cause kidney disease or diabetic nephropathy. Herein, we studied for the first time the electrochemical properties of alloxan on reduced graphene oxide modified glassy carbon electrode (rGO/GCE) in 0.1 M phosphate buffer solution (PBS) at pH 7. The obtained results were compared with graphene oxide modified GCE (GO/GCE) and bare GCE surfaces. The modified rGO/GCE showed well defined redox couple with 10 fold increase in both reduction as well as oxidation peak current for alloxan than that of GO/GCE and bare GCE. Differential pulse voltammetry (DPV) technique shows the linear increase in both oxidation and reduction peak current of alloxan in the range of 30 μM to 3 mM with LOD of 1.2 μM. An amperometric signal of alloxan is also increases with respect to each addition of 50 μM of alloxan on rGO/GCE at constant potential of ?0.05 V. The linear range of alloxan is observed between 50 μM to 750 μM (S/N=3). This kind of rGO/GCE surface is more suitable platform or sensor matrix for estimating unknown concentration of alloxan molecule in the real biological systems.     

纳米金修饰玻碳电极测定邻苯二酚

采用恒电位沉积方法将HAuCl4直接还原成纳米金并修饰于玻碳电极表面,制备了对邻苯二酚具有电催化氧化作用的纳米金修饰电极。邻苯二酚在该修饰电极上发生一可逆的氧化还原反应。在磷酸盐缓冲溶液(pH 7.5)中,当邻苯二酚的浓度为3.0×10-3mol.L-1时,与裸玻碳电极相比,其Epa负位移了170 mV,Epc正位移了50 mV,ΔE下降为60 mV,且峰电流显著增大,氧化峰电流与邻苯二酚浓度在5.0×10-6~4.2×10-3mol.L-1范围内呈线性关系,相关系数为0.997 6,检出限(3σ)为5.0×10-7mol.L-1。在浓度为5.0×10-4mol.L-1测得RSD(n=10)为2.9%,回收率在98.0%~101.0%之间。     

多巴胺在聚亚甲基蓝/石墨烯修饰电极上的电化学行为研究

利用电聚合方法在石墨烯修饰的玻碳电极表面制备了聚亚甲基蓝/石墨烯修饰电极(PMB/GH/GCE)。采用循环伏安法(CV)和差分脉冲伏安法(DPV)研究了多巴胺(DA)和抗坏血酸(AA)在该修饰电极上的电化学行为。在pH 6.9的磷酸盐缓冲溶液中,DA和AA分别在0.208 V和-0.108 V处产生灵敏的氧化峰,与其在聚亚甲基蓝和石墨烯单层修饰电极上的电化学行为相比,两者的峰电流明显增加,峰电位差达316 mV。研究表明,电聚合方法使亚甲基蓝牢固地非共价修饰到石墨烯上,并产生协同增效作用,较好地提高了电极的灵敏度和分子识别性能,有利于在大量AA存在下实现对DA的选择性测定。在1.00×10-3mol/L AA的存在下,DA的差分脉冲伏安法峰电流与其浓度在1.00×10-7～5.00×10-3mol/L范围内呈良好的线性关系,检出限达1.00×10-8mol/L。将该方法用于盐酸多巴胺注射液的测定,结果满意。     

Electrochemical Determination of the p53 Tumor Suppressor Gene Using a Gold Nanoparticle-Graphene Nanocomposite Modified Glassy Carbon Electrode

A novel sensitive and simple electrochemical DNA sensor is reported for the determination of p53 tumor suppressor gene. A gold nanoparticle/graphene nanocomposite-modified glassy carbon electrode was prepared and methylene blue was used as the hybridization redox indicator. Scanning electron microscopic and electrochemical characterization demonstrated that the gold nanoparticles and graphene were present on the electrode. The resulting sensor provided suitable electrochemical response to the p53 tumor suppressor gene with a linear dynamic range from 0.1 to 1000?nM. The limit of detection was 0.012?nM. The sensor was able to differentiate a complete complementary DNA sequence, single-base mismatched DNA sequence, and a three-base mismatched DNA sequence. The precision of the device was satisfactory, with a relative standard deviation of 4.1% for 11 measurements. The combination of gold nanoparticles and a graphene nanocomposite provided enhanced capabilities for the determination of DNA for clinical applications.     

Fabrication of Glucose Biosensor Based on Encapsulation of Glucose‐Oxidase on Sol‐Gel Composite at the Surface of Glassy Carbon Electrode Modified with Carbon Nanotubes and Celestine Blue

A simple procedure was developed to prepare a glassy carbon electrode modified with multi walled carbon nanotubes (MWCNTs) and Celestin blue. Cyclic voltammograms of the modified electrode show stable and a well defined redox couple with surface confined characteristic at wide pH range (2–12). The formal potential of redox couple (E′) shifts linearly toward the negative direction with increasing solution pH. The surface coverage of Celestine blue immobilized on CNTs glassy carbon electrode was approximately 1.95×10^?10 mol cm^?2. The charge transfer coefficient (α) and heterogeneous electron transfer rate constants (k_s) for GC/MWCNTs/Celestine blue were 0.43 and 1.26 s^?1, respectively. The modified electrode show strong catalytic effect for reduction of hydrogen peroxide and oxygen at reduced overpotential. The glucose biosensor was fabricated by covering a thin film of sol‐gel composite containing glucose oxides (GOx) on the surface of Celestine blue /MWCNTs modified GC electrode. The biosensor can be used successfully for selective detection of glucose based on the decreasing of cathodic peak current of oxygen. The detection limit, sensitivity and liner calibration rang were 0.3 μM, 18.3 μA/mM and 10 μM–6.0 mM, respectively. The accuracy of the biosensor for glucose detection was evaluated by detection of glucose in a serum sample, using standard addition protocol. In addition biosensor can reach 90% of steady currents in about 3.0 sec and interference effect of the electroactive existing species (ascorbic acid–uric acid and acetaminophen) was eliminated. Furthermore, the apparent Michaelis–Menten constant 2.4 mM, of GOx on the nano composite exhibits excellent bioelectrocatalytic activity of immobilized enzyme toward glucose oxidation. Excellent electrochemical reversibility of redox couple, high stability, technically simple and possibility of preparation at short period of time are of great advantages of this procedure for modification of glucose biosensor.     

聚溴酚蓝修饰玻碳电极的制备及电化学性质

在含溴酚蓝的磷酸缓冲溶液中,应用循环伏安法于经预处理的玻碳电极上形成聚合物薄膜.结果表明,在-1. 0V~+1. 8V(vs.Ag/AgCl)扫描电位之间形成的薄膜具有较高的电活性和稳定性.该电极对抗坏血酸电化学氧化有催化作用,既使抗坏血酸的氧化电位负移了 270mV,又增大了其氧化峰电流.催化峰电流与抗坏血酸浓度在 2. 5~250μg/mL范围内呈良好的线性关系.     

色氨酸在普鲁士蓝修饰玻碳电极上的电化学行为研究

采用电沉积法制备了普鲁士蓝修饰玻碳电极(PB/GCE),使用循环伏安法(CV)研究了色氨酸(Trp)在修饰电极上的电化学特性,并建立了一种电化学检测色氨酸的新方法。实验结果表明,在优化实验条件下,色氨酸在8.0×10-6～5.0×10-4mol·L-1浓度范围内与峰电流呈良好线性关系,线性回归方程为Ip(μA)=5.8954c(μmol·L-1)-32.91,相关系数r=0.9999(n=8),方法检出限(S/N=3)为3.5×10-7mol·L-1。将该修饰电极用于色氨酸样品的测定,结果满意。初步的反应机理探讨表明,色氨酸在普鲁士蓝电极上的反应可能是以两步进行的两电子氧化过程。     

基于溶胶-凝胶普鲁士蓝膜修饰玻碳电极电催化氧化测定水果中抗坏血酸

制备了一种溶胶-凝胶普鲁士蓝膜修饰玻碳电极,研究了抗坏血酸在该电极上的电催化氧化作用,建立了测定抗坏血酸的方法。在磷酸缓冲溶液(pH 5.0)中,在2.5×10-5-3.2×10-3mol.L-1范围内,抗坏血酸的浓度与氧化峰电流呈线性关系,相关系数为0.999 5,检出限为7×10-6mol.L-1。该修饰电极具有制备简单、灵敏度高、响应速度快、稳定性和重现性好等特点。方法已用于水果中抗坏血酸的测定,所得结果与药典法测得结果一致。     

Electrochemical Behavior and Amperometric Detection of 4‐Chlorophenol on Nano‐Au Thin Films Modified Glassy Carbon Electrode

An amperometric sensor based on nano‐Au thin films was fabricated, by means of which a fast response to 4‐chlorophenol (4‐CP) can be achieved in the range of mM concentrations. The nanostructured Au thin film was prepared on glassy carbon electrodes by a template‐free, double‐potential step electrodeposition technique. Its structural feature can be controlled well by adjusting the deposition time. The amperometric detection of 4‐CP was performed at +0.85 V with a linear detection range from 0.2 to 4.8 mM and a detection limit of 0.11 mM (S/N=3). Besides, the effect of concentrations on the electrochemical behavior of 4‐CP on the Au thin film was investigated by linear sweep voltammetry, differential pulse voltammetry and electrochemical impedance spectroscopy.     

Highly Sensitive Electrochemical Hydrogen Peroxide Sensor Based on Iron Oxide‐Reduced Graphene Oxide‐Chitosan Modified with DNA‐Celestine Blue

The present study describes a novel and very sensitive electrochemical assay for determination of hydrogen peroxide (H₂O₂) based on synergistic effects of reduced graphene oxide‐ magnetic iron oxide nanocomposite (rGO‐Fe₃O₄) and celestine blue (CB) for electrochemical reduction of H₂O₂. rGO‐Fe₃O₄ nanocomposite was synthesized and characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X‐ray diffraction (XRD), electrochemical impedance spectroscopy and cyclic voltammetry. Chitosan (Chit) was used for immobilization of amino‐terminated single‐stranded DNA (ss‐DNA) molecules via a glutaraldehyde (GA) to the surface of rGO‐Fe₃O₄. The MTT (3‐(4,5‐Dim ethylt hiazol‐2‐yl)‐2,5‐diphenylt etrazolium bromide) results confirmed the biocompatibility of nanocomposite. Experimental parameters affecting the ss‐DNA molecules immobilization were optimized. Finally, by accumulation of the CB on the surface of the rGO‐Fe₃O₄‐Chit/ssDNA, very sensitive amperometric H₂O₂ sensor was fabricated. The electrocatalytic activity of the rGO‐Fe₃O₄‐Chit/DNA‐CB electrode toward H₂O₂ reduction was found to be very efficient, yielding very low detection limit (DL) of 42 nM and a sensitivity of 8.51 μA/μM. Result shows that complex matrices of the human serum samples did not interfere with the fabricated sensor. The developed sensor provided significant advantages in terms of low detection limit, high stability and good reproducibility for detection of H₂O₂ in comparison with recently reported electrochemical H₂O₂ sensors.     

A Novel Electrochemical Method for the Analysis of Hydrogen Peroxide with the Use of a Glassy Carbon Electrode Modified by a Prussian Blue/Copper‐Gold Bimetallic Nanoparticles Hybrid Film

A novel Prussian blue/copper‐gold bimetallic nanoparticles hybrid film modified electrode was prepared by electrochemical deposition on a glassy carbon electrode (PB/Cu‐AuNPs/GCE). Morphology and electrochemistry of this electrode were studied by UV‐vis spectroscopy, scanning electron microscopy, X‐ray diffraction, cyclic voltammetry and electrochemical impedance spectroscopy. The sensor showed significantly better electrocatalytic activity for the reduction of hydrogen peroxide in comparison with the single PB/GCE and PB/AuNPs/GCE. This was attributed to the synergistic effect of PB and Cu‐Au bimetallic nanoparticles. Also, the sensor demonstrated an overall high level of performance for the analysis of H₂O₂ in the concentration range from 0.002 to 0.84 mM.     

Electrochemical Detection of 2‐Naphthol at a Glassy Carbon Electrode Modified with Tosflex Film

In this study, a Tosflex (a perfluoro‐anion‐exchange membrane) modified glassy carbon electrode has been used to detect 2‐naphthalenol (2‐naphthol) in aqueous solutions in order to demonstrate the electroanalytical application of Tosflex. 2‐naphthol polymerizes upon electrochemical oxidation at a glassy carbon electrode; however, the current related to this oxidation is too small for analytical purpose at low concentration level. A Tosflex polymer modified glassy carbon electrode (TFGCE) was found of having capability to improve the detection limit because 2‐naphthol molecules deprotonated in basic solutions to form 2‐naphtholate anions that were accumulated to TFGCE by the anion‐exchange characteristic of Tosflex. The accumulated 2‐naphtholate anions were determined with the following differential pulse voltammetry. With 3 minutes accumulation at +0.05 V, the dependence of oxidation current versus concentration was linear from 8×10^?7 M to 1×10^?5 M with a regression coefficient of 0.999 and a detection limit of 2×10^?7 M. Unlike many other anion‐exchange polymer modified electrodes, the TFGCE is stable at highly basic condition.     

乙酰胆碱酯酶/Nafion/普鲁士蓝修饰玻碳电极的制备及其在有机农药检测中的应用

制备了乙酰胆碱酯酶/Nafion/普鲁士蓝修饰的玻碳电极,测试了该修饰电极检测有机农药西维因(carbaryl)和敌百虫(trichlorfon)的性能指标。 利用原子力显微镜和电化学技术研究了电极的构造及其对于有机农药检测性能指标的影响。 结果表明,乙酰胆碱酯酶均匀地分散到Nafion/普鲁士蓝修饰的玻碳电极上。 在最优的实验条件下,构筑的修饰电极检测西维因和敌百虫的线性范围分别为0.01~0.5 μmol/L及2.0~10.0 μmol/L和0.02~1.0 μmol/L及2.0~8.0 μmol/L,检出限分别为5.0和10.0 nmol/L。 并对模拟的实际样品进行了检测,发现该方法有较高的检测灵敏度、较好的重复性和抗干扰性。     

硫堇衍生化自组装膜修饰金电极的电化学性质及其对抗坏血酸的电催化氧化

将硫堇共价键合到自组装在金电极表面的半胱胺单分子层上,制成了衍生化自组装单分子膜修饰电极,并用电化学方法研究了它的电化学性质.循环伏安图显示其在pH＝7.7的磷酸盐缓冲液中,于－0.45～＋0.50V(vs.SCE)范围内有2对氧化还原峰.峰电位分别为E_pa¹＝214mV。E_pc¹＝82mV,E_pa2＝－75mV,E_pc2＝－160mV(vs.SCE).pH在5.0～9.0范围内,峰1有2个质子参与反应,峰2有1个质子参与反应.它的表面电子转移速率常数k_s＝0.02S^－1.此膜对抗坏血酸的氧化有催化作用,其氧化过电位较在裸金电极上降低了约250mV.催化电流与抗坏血酸的浓度在1.0×10^-6～4.0×10^-3mol/L范围内呈良好的线性关系.抗坏血酸催化氧化的异相速率常数为2.68×10^-3cm/s.     

Zinc Oxide Nanoparticle‐modified Glassy Carbon Electrode as a Highly Sensitive Electrochemical Sensor for the Detection of Caffeine

Zinc oxide nanoparticles (ZnO NPs ) were prepared by a simple, convenient, and cost‐effective wet chemical method using the biopolymer starch. The prepared ZnO NPs were characterized by X‐ray diffraction (XRD ), scanning electron microscopy (SEM ), energy‐dispersive X‐ray (EDX ), Fourier transform infrared (FT‐IR ), and UV ‐visible spectroscopic techniques. The average crystallite size calculated from XRD data using the Debye–Scherer equation was found to be 15 nm. The electrochemical behavior of caffeine (CAF ) was studied using a glassy carbon electrode (GCE ) modified with zinc oxide nanoparticles by cyclic voltammetry (CV ) and differential pulse voltammetry (DPV ). Compared to unmodified GCE , ZnO NPs‐ modified GCE (ZnO NPs MGCE ) exhibited excellent electrocatalytic activity towards CAF oxidation, which was evident from the increase in the peak current and decrease in the peak potential. Electrochemical impedance study suggested that the charge‐transfer capacity of GCE was significantly enhanced by ZnO NPs . The linear response of the peak current on the concentrations of CAF was in the range 2–100 μM . The detection limit was found to be 0.038 μM. The proposed sensor was successfully employed for the determination of CAF in commercial beverage samples.     

Polymer/Iron Oxide Nanoparticle Modified Glassy Carbon Electrodes for the Enhanced Detection of Epinephrine

Novel electrochemical sensors for epinephrine (EP) based on a glassy carbon electrode (GCE) modified with a redox polymer film and iron (III) oxide nanoparticles (Fe₂O₃NP) have been developed. Two redox polymers‐poly(brilliant cresyl blue) (PBCB) and poly(Nile blue) (PNB), and two different architectures‐polymer/Fe₂O₃/GCE and Fe₂O₃/polymer/GCE were investigated. The electrochemical oxidation of epinephrine at the modified electrodes was performed by differential pulse voltammetry (DPV), in pH 7 electrolyte, and the analytical parameters were determined. The results show enhanced performance, more sensitive responses and lower detection limits at the modified electrodes, compared to other electrochemical epinephrine sensors reported in the literature. The best voltammetric response with the lowest detection limit was obtained for the determination of epinephrine at PBCB/Fe₂O₃/GCE. The novel sensors are reusable, with good reproducibility and stability, and were successfully applied to the determination of epinephrine in commercial injectable adrenaline samples.