An ethylcarbazole based phosphine oxide derivative as a host for deep blue phosphorescent organic light-emitting diode

Deep blue phosphorescent organic light-emitting diodes (PHOLEDs) were developed using a 9-ethylcarbazole based phosphine oxide material (EPO1). A high triplet energy of 3.01 eV was obtained from the EPO1 host material and efficient energy transfer from the host to the deep blue emitting phosphorescent dopant was observed. A high quantum efficiency of 7.9% with a color coordinate of (0.15, 0.17) was achieved in the deep blue PHOLED using the EPO1 host material.     

氮化镓基蓝光发光二极管伽马辐照的1/f噪声表征

通过电离辐照对氮化镓基蓝光发光二极管器件有源区光/暗电流产生机制的研究, 建立了电离辐照减小发光二极管有效输出功率电学模型.通过电离辐照对氮化镓基蓝光发光 二极管器件有源区1/f噪声影响机制的研究, 建立了电离辐照增大发光二极管1/f噪声的相关性模型.在I < 1 μA 的小注入区,空间电荷区的复合电流随辐照剂量的增加而增加. 同时, 随着电离辐照产生缺陷的增加, 1/f噪声幅度增大. 在 I> 1 mA 的大注入条件下, 由于串联电阻的影响占主导地位,表面复合速率和电流随辐照剂量的增加而增加.同时, 随着电离辐照产生缺陷的增加, 1/f噪声幅度增大.根据辐照前后电流电压试验结果噪声测试结论, 证实了实验结论与理论推导结果的一致性. 在1 μA < I < 5×10^-5 A 的中值电流情况下, 由于高能载流子散射相关的迁移率涨落与辐照新增缺陷引起的载流子数涨落竞争机制, 随着辐照剂量增大, 1/f噪声在频域变化没有明显规律. 但是, 通过1/f噪声时域多尺度熵复杂度分析方法, 得出随着辐照剂量增大, 1/f噪声时域多尺度熵复杂度的结果. 最终证实1/f噪声幅度可以敏感地反映小注入和大注入情况下氮化镓基蓝光发光二极管电离辐照的可靠性. 噪声幅值越大, 则说明辐照感应N_it越高, 暗电流相关的复合电流越大, 光电流相关的扩散电流比例减少, 使得器件发光效率、光输出功率等性能参数下降, 继而影响器件可靠性, 造成失效率显著增大. 1/f噪声时域多尺度熵复杂度可以敏感地反映中值电流情况下氮 化镓基蓝光发光二极管的电离辐照可靠性.多尺度熵复杂度越大, 则说明辐照感应越多, 复合电流越大,器件可靠性越差.本文结论提供了一种基于 1/f噪声的氮化镓基蓝光发光二极管电离辐照可靠性表征方法. 关键词： f噪声')" href="#">1/f噪声 电离辐照 氮化镓基蓝光发光二极管     

Electronic and thermoelectric properties of a single pyrene molecule

We propose a system containing a single pyrene molecule sandwiched between two metallic electrodes. The transport properties of the single pyrene molecule with four configurations are investigated using a steady-state theoretical model. We calculate the transmission probability and the electric current for the structure (1, 8), the structure (1, 7), the structure (1, 5) and the structure (1, 4). By applying a gate voltage on the pyrene molecule, we calculate the thermoelectric properties. The thermoelectric and electron transport properties can be controlled by quantum interference, the contact geometry and the gate voltage. The asymmetric behavior and the splitting of resonances in the transmission spectrum occur due to applying a gate voltage on the pyrene molecule. As a result, the structures (1, 5) and (1, 7) have a maximum value of the figure of merit reaching to 0.8 at the Fermi level. According to the results, the structures (1, 5) and (1, 7) can be act as promising thermoelectric applications in molecular electronics.     

Synthesis and characterization of PPV-based light-emitting copolymer with alkylsilylphenyloxy pendant group for light-emitting diode applications

A novel light-emitting copolymer with high brightness and luminance efficiency was synthesized using the Gilch polymerization method, and its electro-optical properties were investigated. A polymer light-emitting diode (PLED) was fabricated in ITO/PEDOT/light-emitting copolymer/Ca/Al configuration. The turn-on voltage of the PLED was about 5.0 V with maximum brightness and luminance efficiency up to 1420 cd/m² at 16.2 V and 0.5 cd/A at 6.8 V, respectively.     

Pure blue and white light electroluminescence in a multilayer organic light-emitting diode using a new blue emitter

We characterized the 6,12-bis{[N-（3,4-dimethylphenyl）-N-（2,4,5-trimethylphenyl）]amino} chrysene （BmPAC）, which has been proven to be a blue fluorescent emission with high EL efficiency. The blue fluorescent device exhibits good performance with an external quantum efficiency of 5.8% and current efficiency of 8.9 cd/A, respectively. Using BmPAC, we also demonstrate a hybrid phosphorescence/fluorescence white organic light-emitting device （WOLED） with high efficiency of 36.3 cd/A. In order to improve the relative intensity of blue light, we plus a blue light-emitting layer （BEML） in front of the orange light emitting layer （YEML） to take advantage of the excess singlet excitons. With the new emitting layer of BEML/YEML/BEML, we demonstrate the fluorescence/phosphorescence/fluorescence WOLED exhibits good performance with a current efficiency of 47 cd/A and an enhanced relative intensity of blue light.     

Synthesis, optical properties and crystal structures of carbazole end-capped phenylene ethynylene blue light-emitting materials

A class of highly fluorescent and stable carbazole end-capped phenylene ethynylene compounds have been synthesized and characterized. They show high extinction coefficients of absorption () and quantum yields of fluorescence (; Φ_F=0.52-0.73) in dichloromethane. The solid state absorptions and emissions are significantly red-shifted from the dilute solution ones (; ). Their photoluminescent properties and crystal structures have been investigated with the aim of providing a basis for elucidating the structure-physical property relationships. These data indicate their potential use as blue-emitting materials in organic light-emitting diodes (OLEDs).     

Synthesis and surface modification of hydrophobic magnetite to processible magnetite@silica-propylamine

Hydrophobic magnetite nanoparticles with a narrow size distribution were prepared by thermal decomposition of Fe(CO)₅ in octyl ether solution of oleic acid and by consecutive aeration. The nanoparticles were converted into magnetite core/silica shell (magnetite@silica) structured particles with hydrophilic and processible aminopropyl groups on their surfaces.     

Enhancing light extraction of GaN-based blue light-emitting diodes by a tuned nanopillar arrayEnhancing light extraction of GaN-based blue light-emitting diodes by a tuned nanopillar array

Surface patterning of p-GaN to improve the light extraction efficiency of GaN-based blue light-emitting diodes （LEDs） has been investigated. Periodic nanopillar arrays on p-GaN have been fabricated by polystyrene （PS） nanosphere lithog- raphy; the diameter of the nanopillars can be tuned to optimize the electrical and optical properties of the LEDs. The electroluminescence intensity of the nanopillar-patterned LEDs is better than that of conventional LEDs; the greatest en- hancement increased the intensity by a factor of 1.41 at a 20 mA injection current. The enhancements can be explained by a model of bilayer film on a GaN substrate. This method may serve as a practical approach to improve the efficiency of light extraction from LEDs.     

Integral characteristics of vibronic-spin-orbit interactions in a phosphorus-containing analogue of the fluorene molecule

The strengths (P ₀₀ ^s )² and F _VSO ² of the transitions from the triplet sublevels s = z, y, and x of the electronic state ³A″ of the phenyldibenzophosphole (DB(P-Ph)) molecule are calculated taking into account the intramolecular spin-orbit (SO) and joint vibronic-spin-orbit (VSO) interactions. The contributions to the vibronic transition strengths from the SO interactions in different structural elements of the molecule (the C atoms of the dibenzene framework, the P atom, and the Ph substituent) are determined. The effect of the nonplanar nuclear configuration of the DB(P-Ph) molecule on the values of F _VSO ^s is investigated. The radiative deactivation rate constants of the k _rad ^s triplet sublevels T ^s are estimated. It is found that the vibrations of the A′(B₁) symmetry in the fine-structure phosphorescence spectrum of DB(P-Ph) occur due to both the SO coupling exclusively in the P atom and the T ^x → S₀ transition (the x axis is perpendicular to the planar dibenzene framework of the molecule) with a high (preferential) population of this triplet sublevel.     

InGaN/GaN多量子阱蓝色发光二极管的实验与模拟分析

分别采用量子阱模型和量子点模型对蓝色InGaN/GaN多量子阱发光二极管电学和光学特性进行模拟,并和实验测量结果进行了比对,结果发现,量子点模型的引入,很好地解决了I-V和电致发光二方面的实验与理论模型间符合程度不好的问题.同时,在I-V曲线特性模拟中发现,在量子点理论模型的基础上,只有考虑到载流子的非平衡量子传输效应,才能得到和实验相接近的I-V曲线,揭示着在InGaN/GaN 多量子阱发光二极管电输运特性中,载流子的非 关键词： InGaN/GaN 发光二极管 数值模拟 量子点模型     

Enhancing light extraction of GaN-based blue light-emitting diodes by a tuned nanopillar array

Surface patterning of p-GaN to improve the light extraction efficiency of GaN-based blue light-emitting diodes(LEDs) has been investigated. Periodic nanopillar arrays on p-GaN have been fabricated by polystyrene(PS) nanosphere lithography; the diameter of the nanopillars can be tuned to optimize the electrical and optical properties of the LEDs. The electroluminescence intensity of the nanopillar-patterned LEDs is better than that of conventional LEDs; the greatest enhancement increased the intensity by a factor of 1.41 at a 20 mA injection current. The enhancements can be explained by a model of bilayer film on a GaN substrate. This method may serve as a practical approach to improve the efficiency of light extraction from LEDs.     

Synthesis and characterization of indium oxide-hematite magnetic ceramic solid solution

Indium oxide-doped hematite xIn₂O_3*(1-x)??-Fe₂O₃ (molar concentration x = 0.1?C0.7) solid solutions were synthesized using mechanochemical activation by ball milling. XRD patterns yield the dependence of lattice parameters and grain size as function of milling time. After 12 h of milling, the completion of In^3?+? substitution of Fe^3?+? in hematite lattice occurs for x = 0.1. For x = 0.3, 0.5 and 0.7, the substitutions between In^3?+? and Fe^3?+? into hematite and respectively, In₂O₃ lattices occur simultaneously. The lattice parameters of ??-Fe₂O₃ (a and c) and In₂O₃ (a) vary with milling time. For x = 0.1, Mössbauer spectra were fitted with one, two, or three sextets versus milling time, corresponding to gradual substitution of In^3?+? for Fe^3?+? in hematite lattice. For x = 0.3, Mössbauer spectra after milling were fitted with three sextets and two quadrupole-split doublets, representing In^3?+? substitution of Fe^3?+? in hematite lattice and Fe^3?+? substitution of In^3?+? in two different sites of In₂O₃ lattice. For x = 0.5 and 0.7, Mössbauer spectra fitting required two sextets and one quadrupole-split doublet, representing coexistence of In^3?+? substitution of Fe^3?+? in hematite lattice and Fe^3?+? substitution of In^3?+? in indium oxide lattice. The recoilless fraction studied versus milling time for each molar concentration exhibited low values, consistent with the occurrence of nanoparticles in the system. SEM/EDS measurements revealed that the mechanochemical activation by ball milling produced xIn₂O_3*(1-x)??-Fe₂O₃ solid solution system with a wide range of particle size distribution, from nanometer to micrometer, but with a uniform distribution of Fe, In, and O elements.     

Efficiency improvement of red organic light-emitting diodes using a blue phosphorescent exciton blocking layer

Quantum efficiency of red organic light-emitting diodes was improved using a blue phosphorescent emitting layer as an exciton blocking layer. Compared with 8.1% quantum efficiency of standard devices without an exciton blocking layer, high quantum efficiency of 14.1% was obtained using a blue phosphorescent emitting layer between the hole transport layer and the red emitting layer.     

Luminescence mechanisms of green and blue organic light-emitting devices utilizing hole-blocking layers

Optical and electrical measurements on green and blue organic light-emitting devices (OLEDs) with and without hole-blocking layers (HBLs) were performed, and the luminescence mechanisms of green and blue OLEDs utilizing HBLs were investigated by using energy band diagrams and carrier density distributions. The dependence of the electroluminescence efficiencies on the existence of HBLs was described on the basis of a luminescence mechanism. The density distributions of the electrons and the holes in OLEDs under applied electric fields were estimated from the energy band diagrams, taking into account the electronic parameters and the layer thicknesses. The luminescence efficiencies and the color chromaticities were significantly affected by the existence of the HBLs. These analyses can help improve understanding of the luminescence mechanisms at play in and the electroluminescence efficiencies of green and blue OLEDs with HBLs, and the present results provide important information on the optical properties for enhancing the efficiencies of OLEDs operating in the green and the blue regions of the spectra.     

Performance improvement of blue InGaN light-emitting diodes with a specially designed n-AIGaN hole blocking layer

Blue InGaN light-emitting diodes （LEDs） with a conventional electron blocking layer （EBL）, a common n-A1GaN hole blocking layer （HBL）, and an n-A1GaN HBL with gradual A1 composition are investigated numerically, which involves analyses of the carrier concentration in the active region, energy band diagram, electrostatic field, and internal quantum efficiency （IQE）. The results indicate that LEDs with an n-AIGaN HBL with gradual AI composition exhibit better hole injection efficiency, lower electron leakage, and a smaller electrostatic field in the active region than LEDs with a conven tional p-A1GaN EBL or a common n-A1GaN HBL. Meanwhile, the efficiency droop is alleviated when an n-A1GaN HBL with gradual A1 composition is used.     

Performance improvement of blue InGaN light-emitting diodes with a specially designed n-AlGaN hole blocking layer

Blue InGaN light-emitting diodes (LEDs) with a conventional electron blocking layer (EBL), a common n-AlGaN hole blocking layer (HBL), and an n-AlGaN HBL with gradual Al composition are investigated numerically, which involves analyses of the carrier concentration in the active region, energy band diagram, electrostatic field, and internal quantum efficiency (IQE). The results indicate that LEDs with an n-AlGaN HBL with gradual Al composition exhibit better hole injection efficiency, lower electron leakage, and a smaller electrostatic field in the active region than LEDs with a conventional p-AlGaN EBL or a common n-AlGaN HBL. Meanwhile, the efficiency droop is alleviated when an n-AlGaN HBL with gradual Al composition is used.     

Synthesis and characterization of ZnS:Cu,Al phosphor prepared by a chemical solution method

A novel and simple synthesis route for the production of ZnS:Cu,Al sub-micron phosphor powder is reported. Both the host and activator cations were co-precipitated from an ethanol medium by mixing with a diluted ammonium sulfide solution. The co-precipitated ZnS:Cu,Al was in cubic zinc blende structure after an intermediate-temperature furnace annealing. Strong photoluminescent and cathodoluminescent (CL) emission were observed, which was attributed to the 3d¹⁰-3d⁹4s¹ radiative transition at those copper sites. At an accelerating voltage of 1 kV, the CL intensity of the co-precipitated ZnS:Cu,Al sample was recorded 94% of the commercial reference phosphor with the same composition made by high temperature solid-state-reaction method. The particle size of the co-precipitated phosphor powders was found to be controllable simply through adjusting the reactant concentrations. The particle size of the annealed samples was measured by dynamic light scattering, which showed a mean particle diameter between 200 and 700 nm depending on the co-precipitation conditions.     

Threshold reduction in a cyclic photonic molecule laser composed of identical microdisks with whispering-gallery modes

Lasing modes in cyclic photonic molecules (CPMs) composed of several identical thin semiconductor microdisks in free space are studied in a linear approximation. Maxwell's equations with exact boundary conditions and the radiation condition at infinity are considered as a specific eigenvalue problem that enables one to find natural frequencies and threshold gains. It is demonstrated that careful tuning of the distance between the disks in CPMs is able to drastically reduce the lasing thresholds of the whispering-gallery modes having small azimuth indices.