增强型AlGaN/GaN高电子迁移率晶体管高温退火研究

深入研究了两种增强型AlGaN/GaN高电子迁移率晶体管(HEMT)高温退火前后的直流特性变化.槽栅增强型AlGaN/GaN HEMT在500 ℃ N₂中退火5 min后,阈值电压由0.12 V正向移动到0.57 V,器件Schottky反向栅漏电流减小一个数量级.F注入增强型AlGaN/GaN HEMT在 400 ℃ N₂中退火2 min后,器件阈值电压由0.23 V负向移动到-0.69 V,栅泄漏电流明显增大.槽栅增强型器件退火过程中Schottky有效势垒     

AlGaN/GaN高电子迁移率晶体管肖特基高温退火机理研究

在不同应力条件下,研究了AlGaN/GaN高电子迁移率晶体管高温退火前后的电流崩塌、栅泄漏电流以及击穿电压的变化.结果表明,AlGaN/GaN高电子迁移率晶体管通过肖特基高温退火以后,器件的特性得到很大的改善.利用电镜扫描(SEM)和X射线光电子能谱(XPS)对高温退火前、后的肖特基接触界面进行深入分析,发现器件经过高温退火后,Ni和AlGaN层之间介质的去除,并且AlGaN材料表面附近的陷阱减少,使得肖特基有效势垒提高,从而提高器件的电学特性. 关键词： AlGaN/GaN高电子迁移率晶体管 肖特基接触 界面陷阱     

AlGaN/GaN 高电子迁移率晶体管漏电流退化机理研究

本文首先制备了与AlGaN/GaN高电子迁移率晶体管 (HEMT) 结构与特性等效的AlGaN/GaN异质结肖特基二极管, 采用步进应力测试比较了不同栅压下器件漏电流的变化情况, 然后基于电流-电压和电容-电压测试验证了退化前后漏电流的传输机理, 并使用失效分析技术光发射显微镜 (EMMI) 观测器件表面的光发射, 研究了漏电流的时间依赖退化机理. 实验结果表明: 在栅压高于某临界值后, 器件漏电流随时间开始增加, 同时伴有较大的噪声. 将极化电场引入电流与电场的依赖关系后, 器件退化前后的 log(I_FT/E)与√E 都遵循良好的线性关系, 表明漏电流均由电子Frenkel-Poole (FP) 发射主导. 退化后 log(I_FT/E)与√E 曲线斜率的减小, 以及利用EMMI在栅边缘直接观察到了与缺陷存在对应关系的“热点”, 证明了漏电流退化的机理是: 高电场在AlGaN层中诱发了新的缺陷, 而缺陷密度的增加导致了FP发射电流I_FT的增加. 关键词： AlGaN/GaN 高电子迁移率晶体管 漏电流 退化机理     

开态应力下电压和电流对AlGaN/GaN高电子迁移率晶体管的退化作用研究

通过采集等功率的两种不同开态直流应力作用下AlGaN/GaN高电子迁移率晶体管(HEMTs)漏源电流输出特性、源区和漏区大信号寄生电阻、转移特性、阈值电压随应力时间的变化, 并使用光发射显微镜观察器件漏电流情况, 研究了开态应力下电压和电流对AlGaN/GaN高电子迁移率晶体管的退化作用. 结果表明, 低电压大电流应力下器件退化很少, 高电压大电流下器件退化较明显. 高电压是HEMTs退化的主要因素, 栅漏之间高电场引起的逆压电效应对参数的永久性退化起决定性作用. 除此之外, 器件表面损坏部位的显微图像表明低电压大电流下器件失效是由于局部电流密度过高, 出现热斑导致器件损伤引起的.     

用逆压电极化模型对AlGaN/GaN 高电子迁移率晶体管电流崩塌现象的研究

通过自洽求解一维Poisson-Schrdinger方程,模拟了AlGaN/GaN高电子迁移率晶体管在工作时等效外电场对AlGaN/GaN异质结沟道处二维电子气(2DEG)浓度的影响.分析了逆压电极化效应的作用,从正-逆压电极化现象出发,提出了逆压电极化模型.计算结果显示：逆压电极化明显影响2DEG性质,当Al组分x=0.3,AlGaN层厚度为20 nm时,不考虑逆压电极化,2DEG浓度为1.53×10¹³cm^-2;当等效外电压分别为10和15V 关键词： AlGaN/GaN高电子迁移率晶体管 Poisson-Schrdinger方程 逆压电极化模型 电流崩塌     

AlGaN/GaN高电子迁移率晶体管温度传感器特性

本文制作了基于无栅AlGaN/GaN高电子迁移率晶体管结构的温度传感器,并对其温度相关的电学特性进行了表征.实验测试了器件从50℃到400℃的变温电流-电压特性,研究了器件灵敏度随着器件沟道长宽比的变化,并研究了在300—500℃高温的空气和氮气中经过1 h恒温加热后器件的电学特性变化.理论与实验研究结果表明,随着器件沟道长宽比的增大,器件的灵敏度会随之上升;在固定电流0.01 A下,器件电压随温度变化的平均灵敏度为44.5 mV/℃.同时,稳定性实验显示器件具有较好的高温保持稳定性.     

AlGaAs/InGaAs/GaAs赝配高电子迁移晶体管的kink效应研究

利用二维器件模拟软件MEDICI对AlGaAs/InGaAs/GaAs赝配高电子迁移晶体管器(PHEMT)件进行了仿真，研究了PHEMT器件的掺杂浓度与电子浓度分布，PHEMT器件内部的电流走向及传输特性，重点研究了不同温度和不同势垒层浓度情况下PHEMT器件的kink效应.研究结果表明：kink效应主要与处于高层深能级中的陷阱俘获/反俘获过程有关，而不是只与碰撞电离有关. 关键词： 高电子迁移率晶体管 kink效应 二维电子气     

具有高开启/关断电流比的Al2O3/AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

采用原子层淀积(ALD)方法,制备了Al₂O₃为栅介质的高性能AlGaN/GaN金属氧化物半导体高电子迁移率晶体管(MOS-HEMT)。在栅压为-20 V时,MOS-HEMT的栅漏电比Schottky-gate HEMT的栅漏电低4个数量级以上。在栅压为+2 V时,Schottky-gate HEMT的栅漏电为191μA;在栅压为+20 V时,MOS-HEMT的栅漏电仅为23.6 nA,比同样尺寸的Schottky-gate HEMT的栅漏电低将近7个数量级。AlGaN/GaN MOS-HEMT的栅压摆幅达到了±20 V。在栅压V_gs=0 V时, MOS-HEMT的饱和电流密度达到了646 mA/mm,相比Schottky-gate HEMT的饱和电流密度(277 mA/mm)提高了133%。栅漏间距为10μm的AlGaN/GaN MOS-HEMT器件在栅压为+3 V时的最大饱和输出电流达到680 mA/mm,特征导通电阻为1.47 mΩ·cm²。Schottky-gate HEMT的开启与关断电流比仅为10⁵,MOS-HEMT的开启与关断电流比超过了10⁹,超出了Schottky-gate HEMT器件4个数量级,原因是栅漏电的降低提高了MOS-HEMT的开启与关断电流比。在V_gs=-14 V时,栅漏间距为10μm的AlGaN/GaN MOS-HEMT的关断击穿电压为640 V,关断泄露电流为27μA/mm。     

GaN高电子迁移率晶体管强电磁脉冲损伤效应与机理

提出了一种新型GaN异质结高电子迁移率晶体管在强电磁脉冲下的二维电热模型,模型引入材料固有的极化效应,高场下电子迁移率退化、载流子雪崩产生效应以及器件自热效应,分析了栅极注入强电磁脉冲情况下器件内部的瞬态响应,对其损伤机理和损伤阈值变化规律进行了研究.结果表明,器件内部温升速率呈现出"快速-缓慢-急剧"的趋势.当器件局部温度足够高时(2000 K),该位置热电子发射与温度升高形成正反馈,导致温度急剧升高直至烧毁.栅极靠近源端的柱面处是由于热积累最易发生熔融烧毁的部位,严重影响器件的特性和可靠性.随着脉宽的增加,损伤功率阈值迅速减小而损伤能量阈值逐渐增大.通过数据拟合得到脉宽τ与损伤功率阈值P和损伤能量阈值E的关系.     

加载功率与壳温对AlGaN/GaN高速电子迁移率晶体管器件热阻的影响

结温是制约器件性能和可靠性的关键因素, 通常利用热阻计算器件的工作结温. 然而, 器件的热阻并不是固定值, 它随器件的施加功率、温度环境等工作条件的改变而变化. 针对该问题, 本文以CREE公司生产的高速电子迁移率晶体管(HEMT)器件为研究对象, 利用红外热像测温法与Sentaurus TCAD模拟法相结合, 测量研究了AlGaN/GaN HEMT器件在不同加载功率以及管壳温度下热阻的变化规律. 研究发现: 当器件壳温由80 ℃升高至130 ℃时, 其热阻由5.9 ℃/W变化为6.8 ℃/W, 增大15%, 其热阻与结温呈正反馈效应; 当器件的加载功率从2.8 W增加至14 W时, 其热阻从5.3 ℃/W变化为6.5 ℃/W, 增大22%. 对其热阻变化机理的研究发现: 在不同的管壳温度以及不同的加载功率条件下, 由于材料导热系数的变化导致其热阻随温度与加载功率的变化而变化.     

Kink effect in AlGaN/GaN high electron mobility transistors by electrical stress

The kink effect is studied in an AlGaN/GaN high electron mobility transistor by measuring DC performance during fresh, short-term stress and recovery cycle with negligible degradation. Vdg plays an assistant role in detrapping electrons and short-term stress results in no creation of new category traps but an increase in number of active traps. A possible mechanism is proposed that electrical stress supplies traps with the electric field for activation and when device is under test field-assisted hot-electrons result in electrons detrapping from traps, thus deteriorating the kink effect. In addition, experiments show that the impact ionization is at a relatively low level, which is not the dominant mechanism compared with trapping effect. We analyse the complicated link between the kink effect and stress bias through groups of electrical stress states: Vds = 0-state, off-state, on-state (on-state with low voltage, high-power state, high field state). Finlly, a conclusion is drawn that electric field brings about more severe kink effect than hot electrons. With the assistance of electric field, hot electrons tend to be possible to modulate the charges in deep-level trap.     

Novel model of a AlGaN/GaN high electron mobility transistor based on an artificial neural network

In this paper we present a novel approach to modeling AlGaN/GaN high electron mobility transistor(HEMT) with an artificial neural network(ANN).The AlGaN/GaN HEMT device structure and its fabrication process are described.The circuit-based Neuro-space mapping(neuro-SM) technique is studied in detail.The EEHEMT model is implemented according to the measurement results of the designed device,which serves as a coarse model.An ANN is proposed to model AlGaN/GaN HEMT based on the coarse model.Its optimization is performed.The simulation results from the model are compared with the measurement results.It is shown that the simulation results obtained from the ANN model of AlGaN/GaN HEMT are more accurate than those obtained from the EEHEMT model.     

A novel enhancement mode AlGaN/GaN high electron mobility transistor with split floating gates

A novel enhancement-mode AlGaN/GaN high electron mobility transistor(HEMT) is proposed and studied.Specifically,several split floating gates(FGs) with negative charges are inserted to the conventional MIS structure.The simulation results revealed that the V_(th) decreases with the increase of polarization sheet charge density and the tunnel dielectric(between FGs and AlGaN) thickness,while it increases with the increase of FGs sheet charge density and blocking dielectric(between FGs and control gate) thickness.In the case of the same gate length,the V_(th) will left shift with decreasing FG length.More interestingly,the split FGs could significantly reduce the device failure probability in comparison with the single large area FG structure.     

Neutron irradiation effects on AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors (HEMTs) were exposed to 1 MeV neutron irradiation at a neutron fluence of 1 × 10¹⁵ cm^-2. The dc characteristics of the devices, such as the drain saturation current and the maximum transconductance, decreased after neutron irradiation. The gate leakage currents increased obviously after neutron irradiation. However, the rf characteristics, such as the cut-off frequency and the maximum frequency, were hardly affected by neutron irradiation. The AlGaN/GaN heterojunctions have been employed for the better understanding of the degradation mechanism. It is shown in the Hall measurements and capacitance-voltage tests that the mobility and concentration of two-dimensional electron gas (2DEG) decreased after neutron irradiation. There was no evidence of the full-width at half-maximum of X-ray diffraction (XRD) rocking curve changing after irradiation, so the dislocation was not influenced by neutron irradiation. It is concluded that the point defects induced in AlGaN and GaN by neutron irradiation are the dominant mechanisms responsible for performance degradations of AlGaN/GaN HEMT devices.     

Significant performance enhancement in AlGaN/GaN high electron mobility transistor by high-κ organic dielectric

The electrical properties of AlGaN/GaN high electron mobility transistor (HEMT) with and without high-κ organic dielectrics are investigated. The maximum drain current I_{D max} and the maximum transconductance g_{m max} of the organic dielectric/AlGaN/GaN structure can be enhanced by 74.5%, and 73.7% compared with those of the bare AlGaN/GaN HEMT, respectively. Both the threshold voltage V_T and g_{m max} of the dielectric/AlGaN/GaN HEMT are strongly dielectric-constant-dependent. Our results suggest that it is promising to significantly improve the performance of the AlGaN/GaN HEMT by introducing the high-κ organic dielectric.     

High temperature characteristics of AlGaN/GaN high electron mobility transistors

Direct current (DC) and pulsed measurements are performed to determine the degradation mechanisms of AlGaN/GaN high electron mobility transistors (HEMTs) under high temperature. The degradation of the DC characteristics is mainly attributed to the reduction in the density and the mobility of the two-dimensional electron gas (2DEG). The pulsed measurements indicate that the trap assisted tunneling is the dominant gate leakage mechanism in the temperature range of interest. The traps in the barrier layer become active as the temperature increases, which is conducive to the electron tunneling between the gate and the channel. The enhancement of the tunneling results in the weakening of the current collapse effects, as the electrons trapped by the barrier traps can escape more easily at the higher temperature.     

Electric field driven plasmon dispersion in AlGaN/GaN high electron mobility transistors

We present a theoretical study on the electric field driven plasmon dispersion of the two-dimensional electron gas(2DEG)in AlGaN/GaN high electron mobility transistors(HEMTs).By introducing a drifted Fermi–Dirac distribution,we calculate the transport properties of the 2DEG in the AlGaN/GaN interface by employing the balance-equation approach based on the Boltzmann equation.Then,the nonequilibrium Fermi–Dirac function is obtained by applying the calculated electron drift velocity and electron temperature.Under random phase approximation(RPA),the electric field driven plasmon dispersion is investigated.The calculated results indicate that the plasmon frequency is dominated by both the electric field and the angle between wavevector and electric field.Importantly,the plasmon frequency could be tuned by the applied source–drain bias voltage besides the gate voltage(change of the electron density).     

An improved EEHEMT model for kink effect on AlGaN/GaN HEMT

In this paper, a new current expression based on both the direct currect(DC) characteristics of the AlGaN/GaN high election mobility transistor(HEMT) and the hyperbolic tangent function tanh is proposed, by which we can describe the kink effect of the AlGaN/GaN HEMT well. Then, an improved EEHEMT model including the proposed current expression is presented. The simulated and measured results of I–V, S-parameter, and radio frequency(RF) large-signal characteristics are compared for a self-developed on-wafer AlGaN/GaN HEMT with ten gate fingers each being 0.4-μm long and 125-μm wide(Such an AlGaN/GaN HEMT is denoted as AlGaN/GaN HEMT(10 × 125 μm)). The improved large signal model simulates the I–V characteristic much more accurately than the original one, and its transconductance and RF characteristics are also in excellent agreement with the measured data.     

Influence of a drain field plate on the forward blocking characteristics of an AlGaN/GaN high electron mobility transistor

In this paper,the influence of a drain field plate(FP)on the forward blocking characteristics of an AlGaN/GaN high electron mobility transistor(HEMT)is investigated.The HEMT with only a gate FP is optimized,and breakdown voltage VBRis saturated at 1085 V for gate–drain spacing LGD≥8μm.On the basis of the HEMT with a gate FP,a drain FP is added with LGD=10μm.For the length of the drain FP LDF≤2μm,VBRis almost kept at 1085 V,showing no degradation.When LDFexceeds 2μm,VBRdecreases obviously as LDFincreases.Moreover,the larger the LDF,the larger the decrease of VBR.It is concluded that the distance between the gate edge and the drain FP edge should be larger than a certain value to prevent the drain FP from affecting the forward blocking voltage and the value should be equal to the LGDat which VBR begins to saturate in the first structure.The electric field and potential distribution are simulated and analyzed to account for the decrease of VBR.