二级6—8型大腔体装置的高压发生效率机理研究

利用自行设计与集成的二级6—8型大腔体静高压装置,研究了影响八面体压腔高压发生效率的主要因素及机理,并提出了一种八面体压腔密封的简化力学模型.针对于10/4（八面体传压介质边长为10 mm,二级WC立方体增压块截角边长为4 mm）组装的实验结果发现：预密封边尺寸会显著影响八面体压腔的压力产生效率;在腔体压力为12 GPa左右时,高压发生效率随八面体MgO传压介质初始密度的增加而提高;在15 GPa以上时,影响压力产生效率的主要因素是WC增压立方块本身的强度以及加压过程中所形成密封边的尺寸及材料. 关键词： 6—8型大腔体静高压装置 压力产生效率     

基于铰链式六面顶压机的二级6-8型大腔体静高压装置

报道了一种新型二级6-8型大腔体静高压装置.该装置是以国产DS6×800T铰链式六面顶压机为构架,在其六面体压腔中直接放入二级6-8模(球分割)增压装置以产生10GPa以上的压力,还实验了不同规格的预密封边和不同密度的叶蜡石对压力产生效率的影响,在室温下用BiⅠ-Ⅱ(2.55GPa),Ⅲ-Ⅴ(7.7GPa)和SnⅠ-Ⅱ(9.4GPa)在高压下的相变对14／8(8面体传压介质边长／8面体压腔边长)规格压腔进行了压力标定.实验结果表明,该系统可以在加载压力(油压)约为3×10⁶N(～42 关键词： 铰链式六面顶压机 6-8型球分割大腔体静高压装置 压力标定     

Theoretical description of thermomechanical effects in high pressure apparatus

Abstract

Numerical calculations are used to study stress-strain state of high pressure apparatus components in compression, heating, cooling and unloading with regard to large elastoplastic deformations, high pressures and temperatures, anisotropy of materials and contact interaction. Regularities of HPA components deformation in the processes under consideration are studied.     

大腔体静高压技术的发展及应用

大腔体静高压技术在现代工业和高压科学研究中具有基础性的重要意义,已被广泛应用于工业和科研领域,如超硬材料的合成、凝聚态物质在高温高压极端条件下的行为与物性研究等。经过逾半个世纪的不懈努力,以国产铰链式六面顶压机为代表的大腔体静高压技术与设备取得了长足的发展和丰硕的成果,改变了长期以来我国大腔体静高压技术落后于国外的局面。文章以四川大学高压科学与技术实验室为例,对我国大腔体静高压技术及装置从起步研制到世界领先的发展历程和技术特点进行了介绍。同时,基于典型大腔体静高压技术、装置及主要应用,展望了我国相关领域的发展前景。     

High-temperature calibration of a multi-anvil high pressure apparatus

Fusion and solidification of Al and Ag samples, as well as Fe₉₃–Al₃–C₄, Fe₅₆–Co₃₇–Al₃–C₄, and Fe_57.5–Co₃₈–Al₁–Pb_0.5–C₃ alloys (in wt%), have been investigated at 6.3?GPa. Heater power jumps due to heat consumption and release on metal fusion and solidification, respectively, were used to calibrate the thermal electromotive force of the thermocouple against the melting points (mp) for Ag and Al. Thus, obtained corrections are +100°C (for sample periphery) and +65°C (center) within the 1070–1320°C range. For small samples positioned randomly in the low-gradient zone of a high pressure cell, the corrections should be +80°C and +84°C at the temperatures 1070°C and 1320°C, respectively. The temperature contrast recorded in the low-gradient cell zone gives an error about ±17°C. The method has been applied to identify the mp of the systems, which is especially important for temperature-gradient growth of large type IIa synthetic diamonds.     

Hybrid-toroidal anvil: a replacement for the conventional WC anvil used for the large volume cubic high pressure apparatus

We propose a design and operation of a hybrid-toroidal anvil used for the large volume cubic high pressure apparatus (LV-CHPA), such that it is possible to obtain a higher sintered quality, less weight and cost of tungsten carbide (WC) anvil than the conventional anvil. We use the finite element simulations to show the distributions of the stress on the surface and in the bulk of the WC anvils, and conclude that, for a given load on the hybrid-toroidal anvil, the volume of the compressed press medium has increased by 4.88%, and the rate of the transmitted pressure has increased by 6.72% compared with the conventional anvil. Furthermore, the advantages of the hybrid-toroidal anvil are that the movement of anvils increases by 37.14% and the growth rate of the fatigue crack decreases by 40%. This has been proved by the high pressure experiments. This work gives an approach to optimize the WC anvils used for the LV-CHPA and presents a simple method to achieve the higher sample pressure and the larger sample volume.     

滑块式六含八超高压实验装置及其压力温度标定

报道了一种新型六含八超高压实验装置.三柱式的机体框架与滑块式上三下三模具同为三次对称结构,在力学上较为合理.该装置加压时具有自动校准位置能力,同步性和重复性好.模具推动八块硬质合金压砧在叶腊石八面体中产生高压.分别采用Bi丝和ZnTe晶体的压致相变点255,77,96,12 GPa,对截角边长8 mm压砧和125 mm边长叶腊石块组合的实验体系进行了室温下的压力标定,结果表明压力可达12 GPa以上.在10 GPa压力下,用WRe3-WRe25热电偶将温度标定到1560 ℃,并结合铁碳二元相图和钢 关键词： 压力标定 温度标定 六含八多压砧模具 高压装置     

Finite element analysis and experiment on high pressure apparatus with split cylinder

Ultra-high pressure belt-type die was designed with a large sample volume prism cavity and a split cylinder which was divided into eight segments to eliminate circumferential stress. The cylinder of this type die has no cambered surface on inner wall, and the inner hole is a hexagonal prism-type cavity. The divided bodies squeeze with each other, providing the massive support and lateral support effect of the cylinder. Simulation results indicate that the split cylinder with the prism cavity possesses much smaller stress and more uniform stress distribution. The split cylinder with the prism cavity has been shown to bear larger compressive stresses in radial, circumferential and axial directions due to its structure, and tungsten carbide is most effective in pure compression so this type cylinder could bear higher pressure. Experimental results prove that the high pressure apparatus with a prism-type cavity could bear higher pressure. The apparatus with a prism cavity could bear 52.2% more pressure than the belt-type die.     

一种以压力一维均匀分布为特征的长条形对顶压砧

针对圆形端面平面对顶压砧装置中压力梯度大的问题, 本文设计了一种长条形端面的平面对顶压砧, 相应的封垫也改为长条形. 原理分析表明: 这种压砧可在沿长条形中心线的狭长区域内产生均匀分布的高压力. 本文采用长20 mm宽5 mm长条形端面的硬质合金压砧配合叶腊石封垫进行压力标定, 实验结果显示: 这种装置可产生10 GPa以上的高压, 在长条形中心线上至少12 mm长度范围内的不同位置上产生的压力基本一致, 在2.55 GPa压力时测量偏差小于2.0%, 在7.7 GPa时测量偏差小于3.6%. 这种特点很有利于对细长样品进行精确的高压物性测量.     

High pressure and high temperature generation using small-sized cubic-type multi-anvil apparatus

High pressure and high temperature conditions of 4 GPa and 500°C were generated using a small-sized cubic-type multi-anvil apparatus, which was originally developed for high pressure and low temperature experiments. The drop in pressure was negligible as the temperature was increased from room temperature to 300°C at 4.5 GPa under conditions where the press was clamped. Two-dimensional X-ray diffraction images were successfully obtained from a pure aluminum specimen at 4 GPa and 500°C in the angle-dispersive mode.     

Pressure generation to 50 GPa in Kawai-type multianvil apparatus using newly developed tungsten carbide anvils

A pressure generation test for Kawai-type multianvil apparatus (KMA) has been made using second-stage anvils of a newly developed ultra-hard tungsten carbide composite. Superb performance of the new anvil with significantly less plastic deformation was confirmed as compared to those commonly used for the KMA experiments. A maximum pressure of ～48?GPa was achieved using the new anvils with a truncation edge length (TEL) of 1.5?mm, based on in situ X-ray diffraction measurements. Further optimization of materials and sizes of the pressure medium/gasket should lead to pressures even higher than 50?GPa in KMA using this novel tungsten carbide composite, which may also be used for expansion of the pressure ranges in other types of high pressure apparatus operated in large volume press.     

A combination of a Drickamer anvil apparatus and monochromatic X‐rays for stress and strain measurements under high pressure

A modified Drickamer anvil apparatus has been developed to combine with monochromatic synchrotron radiation for high‐pressure X‐ray diffraction and radiography in the GSECARS bending‐magnet station, 13‐BM‐D, at the Advanced Photon Source, Argonne, USA. Using this experimental set‐up, deformation experiments can be carried out at pressures in excess of 30 GPa at high temperatures. Differential stresses and total axial strains of polycrystalline platinum and Mg₂SiO₄ ringwoodite have been measured up to 32 GPa at room temperature using tungsten carbide anvils. The total axial strain of the platinum increases with pressure and reaches about 55% at the highest pressure. A test run using a composite sintered diamond anvil system was performed. The use of X‐ray‐tranparent anvils enables the entire Debye rings to be observed up to 10° 2θ. With high‐energy photons (65–70 keV), this allows a coverage in Q (= 2π sinθ/λ) to about 3 Å^?1, thus making it possible to evaluate hydrostatic pressure and differential stress in crystalline minerals using diffraction. This, coupled with the ability to determine axial strain, allows deformation studies to be performed to pressures above 30 GPa.     

Large single crystal diamond grown in FeNiMnCo-S-C system under high pressure and high temperature conditions

Large diamonds have successfully been synthesized from FeNiMnCo-S-C system at temperatures of 1255-1393 ℃and pressures of 5.3-5.5 GPa.Because of the presence of sulfur additive,the morphology and color of the large diamond crystals change obviously.The content and shape of inclusions change with increasing sulfur additive.It is found that the pressure and temperature conditions required for the synthesis decrease to some extent with the increase of S additive,which results in left down of the V-shape region.The Raman spectra show that the introduction of additive sulfur reduces the quality of the large diamond crystals.The x-ray photoelectron spectroscopy(XPS) spectra show the presence of S in the diamonds.Furthermore,the electrical properties of the large diamond crystals are tested by a four-point probe and the Hall effect method.When sulfur in the cell of diamond is up to 4.0 wt.%,the resistance of the diamond is 9.628×10~5 Ω·cm.It is shown that the large single crystal samples are n type semiconductors.This work is helpful for the further research and application of sulfur-doped semiconductor large diamond.     

Pressure calibration in high pressure EXAFS experiments

Abstract

To avoid glitches due to Bragg reflection we use boron carbide anvils for our high pressure EXAFS experiments. Since boron carbide precludes the ruby fluorescence pressure calibration we use the EXAFS of selected materials to measure the reduction with pressure of the nearest neighbor distance and infer the pressure from an isothermal equation of state. The requirements for a good pressure calibrant and the difficulties in EXAFS data analysis are discussed. Cu, NaBr and RbCl have successfully been tested as pressure calibrants.     

利用围压提高二级大腔体静高压装置压力极限的初步实验探索

采用基于国产铰链式六面顶压机二级6-8型大腔体静高压装置中的10/4(即八面体传压介质边长为10mm,二级WC-Co硬质合金立方块截角边长为4mm)组装,选择不同的围压材料和传压硬质合金台棱、圆片,在室温下用ZnTe的高压相变对压腔进行了压力标定。实验结果表明,叶蜡石是较合适的围压材料;但由于传压台棱、圆片自身强度的限制,及一级压腔形成的围压值较低等原因,致使实验没有达到预期的末级压砧围压增强效果。通过结合两种压腔的力学简化模型分析得知,围压材料与二级增压装置的预密封边共同形成了二级压腔的密封边,该大面积密封边消耗了系统的大部分加载力,因此在围压实验中没有观测到二级6-8型大腔体静高压装置压力极限的提高。     

A high pressure,high temperature study of 1,1-diamino-2,2-dinitro ethylene

We report a synchrotron energy-dispersive X-ray diffraction study of the novel high explosive 1,1-diamino-2,2-dinitroethylene at high pressures and high temperatures. Pressure was generated using a Paris–Edinburgh cell to employ larger sample volumes. High temperatures were created using a resistive graphite cylinder surrounding the sample. The PT phase diagram was explored in the 3.3 GPa pressure range and in the ～ 400°C temperature range. We believe that the sample commenced in the α-phase and then ended up in an amorphous phase when the temperature increased beyond 280°C near 2 GPa, which we believe to be the γ-phase. Further pressure and temperature cycling suggests that the sample transformed reversibly into and out of the amorphous phase near the phase line.     

A study on the electrical property of HgSe under high pressure

Using a microcircuit fabricated on a diamond anvil cell, we have measured in-situ conductivity of HgSe under high pressures, and investigated the temperature dependence of conductivity under several different pressures. The result shows that HgSe has a pressure-induced transition sequence from a semimetal to a semiconductor to a metal, similar to that in HgTe. Several discontinuous changes in conductivity are observed at around 1.5, 17, 29 and 49GPa, corresponding to the phase transitions from zinc-blende to cinnabar to rocksalt to orthorhombic to an unknown structure, respectively. In comparison with HgTe, it is speculated that the unknown structure may be a distorted CsCl structure. For the cinnabar-HgSe, the energy gap as a function of pressure is obtained according to the temperature dependence of conductivity. The plot of the temperature dependence of conductivity indicates that the unknown structure of HgSe has an electrical property of a conductor.     

Hardness of materials at high temperature and high pressure

The intrinsic character of the correlation between hardness and thermodynamic properties of solids has been established. The proposed thermodynamic model of hardness allows one to easily estimate hardness and bulk moduli of known or even hypothetical solids from the data on Gibbs energy of atomization of the elements or on the enthalpy at the melting point. The correctness of this approach is illustrated by an example of the recently synthesized superhard diamond-like BC₅ and orthorhombic modification of boron, γ-B₂₈. The pressure and/or temperature dependences of hardness were calculated for a number of hard and superhard phases, i.e. diamond, cBN, B₆O, B₄C, SiC, Al₂O₃, β-B₂O₃ and β-rh boron. Excellent agreement between experimental and calculated values is observed for temperature dependences of Vickers and Knoop hardness. In addition, the model predicts that some materials can become harder than diamond at pressures in the megabar range.     

High pressure generation in the Kawai-type multianvil apparatus equipped with sintered diamond anvils

ABSTRACT

Generation of high pressure is a key to the investigation of the interior of the Earth. The Kawai-type multianvil apparatus (KMA) has been widely used in the fields of Earth science and material science. In conventional KMA, tungsten carbide (WC) has been used as the second stage anvil material. However, attainable pressure is limited to ～70?GPa even if newly developed WC is used. Recently, on the other hand, second stage anvils of sintered diamond that is much harder than WC have enabled us to extend the pressure range of KMA up to 120?GPa, corresponding to the pressure of the D” layer in the Earth’s mantle. It is evident that our development of pressure generation facilitates the investigation of the structure and dynamics of the deep mantle of the Earth.     

A tof neutron diffraction system for high pressure and low temperature

Abstract

Time-of-flight method of neutron diffraction is applied for materials under high pressure and low temperature. Extra-scattering from the pressure cell is reduced by geometrical design and by shielding with boron-plastics. Temperature is controled by adjusting the supply of liquid nitrogen: Successive transformations with pressure are observed in heavy ice.