Bathocuproine/Ag复合电极对于聚合物光伏器件效率和稳定性的影响

采用Bathocuproine/Ag (BCP/Ag)复合电极代替Ca/Al复合电极, 制备PTB7:PC71BM 作为光敏层的聚合物光伏器件, 并通过改变BCP薄膜厚度来研究BCP/Ag复合电极对于器件光电转换器和稳定性的影响. 研究发现: 在光敏层和金属电极之间插入BCP修饰层后, 器件性能得到了显著的改善, 在BCP厚度为5 nm时, 器件的效率达到了6.82%, 且略高于Ca/Al复合电极的器件效率; 相比于采用Ca/Al复合电极的器件, BCP/Ag复合电极增大了器件的短路电流和外量子效率, 使器件效率得到提高; 同时器件的稳定性得到了显著的改善, BCP/Ag 复合电极器件的衰减速率几乎和未插入BCP的器件衰减速率相同, 相对于Ca/Al复合电极器件大幅提高.     

Solvent-vapour treatment induced performance enhancement of amplified spontaneous emission based on poly[2-methoxy-5-(2’-ethyl-hexyloxy)-1,4-phenylene vinylene]

In this work,performance enhancements of amplified spontaneous emission(ASE) from poly[2-methoxy-5-(2éthyl-hexyloxy)-1,4-phenylene vinylene](MEH-PPV) have been achieved via solvent vapour treatment.Correlations between the morphology of the film and the optical performance of polymer-based ASE are investigated.The active layers are characterised by atomic force microscopy and optical absorption.The results show that the solvent-vapour treatment can induce the MEH-PPV self-organisation into an ordered structure with a smooth surface,leading to enhanced optical gain.Thus the solvent-vapour treatment is a good method for improving the optical properties of the MEH-PPV.     

多环类苝四甲酸二酐插入层对ZnO纳米棒和聚合物复合太阳电池性能的影响

以ZnO纳米棒和聚[2-甲氧基-5-(2-乙基-己氧基)-1,4-苯撑乙烯撑](MEH-PPV)的复合体系作为光敏层制备了太阳电池.为了增大电池的光吸收,在ZnO纳米棒与MEH-PPV之间插入了有机n型小分子多环类苝四甲酸二酐(PTCDA),制备了不同厚度的PTCDA、结构为ITO/ZnO纳米棒/PTCDA/MEH-PPV/Au的太阳电池.实验发现,插入PTCDA后,电池在可见光区的吸收增强,光生激子数量增大,光电流密度增大.当蒸镀的PTCDA厚度为40 nm时,薄膜的粗糙度适中,表面形貌较为平滑,器件性 关键词： 有机太阳电池 ZnO纳米棒 聚合物     

Effect of solvents on the performance and morphology of polymer photovoltaic devices

In the polymer photovoltaic devices (PVDs), the performance of devices was strongly influenced by region-regularity, number average molecular weight and casting solvents of polymers. In this work, we fabricated p–n bulk-hetero-junction PVDs based on poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C₆₀-butyric acid methyl ester (PCBM) using various solvents such as chloroform (CF), chlorobenzene (CB), dichlorobenzene (DCB), and mixed solvent (CF/CB, CF/DCB). Thin film of active layer with P3HT/PCBM was prepared by spin coating and thermal annealing at 150 °C with fixed thickness about 110 nm by adjusting solution concentration. The crystalline morphology and layered phase for the active layer were studied by atomic force microscopy and X-ray diffraction, respectively. We investigated the performance of solar cells according to different morphology and crystallinity of active layer by various solvent and mixed solvent.     

Effects of acetone-soaking treatment on the performance of polymer solar cells based on P3HT/PCBM bulk heterojunction

The improvement of the acetone-soaking treatment to the performance of polymer solar cells based on the P3HT/PCBM bulk heterojunction is reported. Undergoing acetone-soaking, the PCBM does not distribute uniformly in the vertical direction, a PCBM enrichment layer forms on the top of the active layer, which is beneficial to the collec- tion of the carriers and blocking the inverting diffusion carriers. X-ray photoelectron spectroscopy （XPS） analysis reveals that the PCBM weight ratio on the top of the active layer increases by 20% after the acetone-soaking treatment. Due to the nonuniform distribution of PCBM, the short-circuit current density, the open-circuit voltage, and the fill factor are enhanced significantly. Finally, the power conversion efficiency of the acetone-soaking device increases by 31% compared with the control device.     

新型高效聚合物/富勒烯有机光伏电池研究进展

有机聚合物/富勒烯本体异质结光伏电池以其不断提高的能量转换效率受到了研究人员的广泛关注, 近年来成为光伏电池研究领域的热点之一. 本文主要通过对聚合物/富勒烯太阳能电池的内部机理,包括光吸收、激子扩散和解离以及自由载流子输运和提取等关键科学问题, 从器件材料和结构优化、形貌控制和界面修饰等不同侧面介绍了提高聚合物/富勒烯太阳能电池性能的方法, 讨论了各种器件的结构和能量转换效率, 对于进一步开展这方面的研究工作指明了方向, 最后对其未来的发展前景做出了展望.     

铁电半导体耦合光伏器件的历史与最新进展

本文介绍了新型铁电-半导体耦合光伏器件的发展历史和现状, 阐述了所观察到的非经典行为, 即开路电压在直流偏置电场控制下的迟滞的现象. 将之与含有光诱导偶极子场的有机光伏器件和量子点电池、压电光电子器件、铁电光伏器件、钙钛矿电池等进行比较, 发现偶极子极化电场在多种光伏器件中均存在, 甚至可能起到主导作用. 因此, 提出了偶极子场半导体器件的概念, 期望从更广义的范围涵盖结场型器件和非结场型偶极子器件, 为促进光伏发电领域更多的创新提供思路.     

基于光学与光—电转换模型对聚合物电池功能层厚度与性能相关性分析

本文基于Forouhi-Bloomer 模型得到了这种功能层的光学常数.根据菲涅耳系数矩阵法计算了这种器件内的光电场分布,并计算了不同厚度的聚合物功能层的光子吸收数.同时,通过Onsager-Braun理论,分析了在无外加电场下聚合物功能层厚度对激子分离概率的影响.理论分析和实验结果证明:在特定的薄膜制备工艺下,器件结构为ITO/PEDOT/ P3HT:PC₆₀BM /LiF/Al时,聚合物功能层厚度在100 nm左右时,可以使器件的光子吸收数最大化,同时避免了激子分离概率的降低. 关键词： 光学常数 激子 聚合物太阳能电池     

多温度阶梯退火对有机聚合物太阳能电池器件性能的影响

以聚3-己氧基噻吩(P3HT)作为给体,富勒烯衍生物(ICBA)作为受体,制备了体异质结结构的聚合物太阳能电池,研究不同热退火条件对器件的光伏输出特性及稳定性的影响.研究发现,采用多温度、阶梯退火比单一温度退火能使器件的光伏输出性能明显提高,与此同时器件的寿命显著延长,可以在未封装的环境下保持器件性能的稳定,减缓器件的衰退.     

Effect of sorbitol doping in PEDOT:PSS on the electrical performance of organic photovoltaic devices

Organic photovoltaic cells have important advantages, such as low cost and mechanical flexibility. The conducting polymer poly(3,4 ethylenedioxy-thiophene):poly(styrene sulfonate) (PEDOT:PSS) has been widely used as an interfacial layer or a polymer electrode in polymer electronic devices, such as photovoltaic devices and light-emitting diodes. In this report, we discuss the direct current (DC) conductivity of PEDOT:PSS films containing various weight ratios of sorbitol dopant. The work function is shown to steadily decrease with increasing dopant content. With different dopant contents, illuminated current–voltage photovoltaic characteristics were observed. Ultraviolet photoelectron spectroscopy (UPS) analysis revealed that the work function of the PEDOT:PSS was affected by its sorbitol content. The morphologies of the doped PEDOT:PSS films were characterized by atomic force microscopy (AFM). For the device fabrication, we made organic photovoltaic cells by a spin-coating process and Al deposition by thermal evaporation. The sorbitol dopant is able to improve the efficiency of the device.     

制膜工艺对聚合物太阳电池性能影响的研究

用渡越时间法（TOF）分别测试了采用旋涂和滴涂方法制备的poly［2-methoxy-5-（2′-ethylhexyloxy）-1,4- phenylenevinylene］（MEH-PPV）薄膜的空穴迁移率,用原子力显微镜对这两种方法制备的薄膜表面形貌进行了研究.结果表明使用滴涂法有利于聚合物形成有序薄膜结构,能有效提高空穴迁移率.用滴涂法制备的基于MEH-PPV：phenyl C61- butyric acid methyl ester（PCBM）共混薄膜的太阳电池,对比用旋涂法制备的太阳电池,其能量 关键词： 太阳电池 聚合物 迁移率     

Improving performance of polymer solar cell by adjusting crystallinity and nanoscale phase separation

In this paper, we report a high-performance P3HT/PCBM bulk-heterojunction solar cell with a power conversion efficiency of 4.85% fabricated by adjusting polymer crystallinity and nanoscale phase separation using an ultrasonic irradiation mixing approach of the polymer. The results of grazing incidence X-ray diffraction, UV/Vis spectroscopic, and atomic force microscopic measurements of the P3HT/PCBM blend films reveal that the P3HT/PCBM film fabricated by ultrasonic irradiation mixing P3HT and PCBM solutions for 10 min has higher degree of crystallinity, higher absorption efficiency, and better phase separation, which altogether account for the higher charge transport properties and photovoltaic cell performance.     

磁场对聚合物光电池中电流的影响

制备了结构为 ITO/PEDOT:PSS/P3HT:PCBM/Ca/Al的聚合物光电池器件,并在不同偏压下,分别测量了器件的光电流和暗电流随外加磁场的变化. 发现随外加磁场增加,光电流增强,暗电流减弱. 从聚合物光电池中光电流和暗电流的产生机制出发,对该现象进行了解释,认为外加磁场可以有效改变单重态极化子对和三重态极化子对之间的相对比例,进而使自由载流子浓度增加. 光生自由载流子浓度增加是光生电流增强的原因,而自由载流子与三重态激子的相互作用导致了暗电流减弱. 开路电压附近,光电流随磁场增加而增强可以近似 关键词： 聚合物光电池 磁场效应 光生电流 极化子对     

Solvent-vapour treatment induced performance enhancement of amplified spontaneous emission based on poly[2-methoxy-5-（2＇-ethyl-hexyloxy）-l, 4-phenylene vinylene]

In this work, performance enhancements of amplified spontaneous emission （ASE） from poly[2-methoxy-5-（2＇- ethyl-hexyloxy）-l,4-phenylene vinylene] （MEH-PPV） have been achieved via solvent vapour treatment. Correlations between the morphology of the film and the optical performance of polymer-based ASE are investigated. The active layers are characterised by atomic force microscopy and optical absorption. The results show that the solvent-vapour treatment can induce the MEH-PPV self-organisation into an ordered structure with a smooth surface, leading to enhanced optical gain. Thus the solvent-vapour treatment is a good method for improving the optical properties of the MEH-PPV.     

Improving the performance of polymer solar cells by adjusting the crystallinity and nanoscale phase separation

In this paper, we report a high-performance P3HT/PCBM bulk-heterojunction solar cell with a power conversion efficiency of 4.85% fabricated by adjusting the polymer crystallinity and nanoscale phase separation using an ultrasonic irradiation mixing approach for the polymer. The grazing incidence X-ray diffraction, UV/Vis spectroscopic, and atomic force microscopic measurement results for the P3HT/PCBM blend films reveal that the P3HT/PCBM film fabricated by ultrasonic irradiation mixing of the P3HT and PCBM solutions for 10 min has a higher degree of crystallinity, a higher absorption efficiency, and better phase separation, which together account for the higher charge transport properties and photovoltaic cell performance.     

不同比例的MEH-PPV与PCBM共混体系光电池性能研究

以MEH-PPV(poly(2-methoxy-5-(2^/-ethylhexoxy)-1,4-phenylene vinylene)为电子给体材料(donor,D), PCBM(1-(3-methoxycarbonyl)-propyl-1-1-phenyl-(6,6)C₆₁)为电子受体材料(acceptor,A),制成了不同比例的共混体系太阳电池.从不同比例的D/A材料共混体系的原子力图、光荧光谱、器件的单电荷传输的暗导J-V图、太阳电池的光敏图及器件双电荷传输的光、暗导J-V图方面,详细分析了不同比例的D/A材料对器件性能影响.得出了当D/A材料比例为1∶4时,器件中活性层能形成良好的互穿网络,光生激子能有效地分离,被分离的电荷能有效地传输,太阳电池的性能最好.其光电池在100mW/cm²强度光照下,其开路电压V_oc为0.8V,短路电流密度J_sc为3.47mA/cm²,填充因子FF为55.9%,能量转换效率η为1.55%. 关键词： 太阳能电池 聚合物 性能     

N-type amorphous silicon-based bilayers for cost-effective thin-film silicon photovoltaic devices

We investigate the improvement of p–i–n type thin-film silicon (Si) solar cells by employing a hydrogenated n-type amorphous Si (n-a-Si:H)-based bilayer. The initial conversion efficiency (η) of a-Si:H single-junction solar cells is improved from 9.2 to 10.0%. The developed n-a-Si:H-based bilayer is also suitable for a-Si:H/hydgrogenated microcrystalline Si (μc-Si:H) double-junction solar cells, and thus initial η is improved from 10.4 to 10.8%. With a further optimization, initial η of 11.3% and stabilized η of 10.1% are achieved. Since the n-a-Si:H-based bilayer is easily formed using a conventional process, it can be a promising option for cost-effective mass production of large-area thin-film Si solar modules.     

Improved performance of polymer solar cells by using inorganic,organic, and doped cathode buffer layers

The interface between the active layer and the electrode is one of the most critical factors that could affect the device performance of polymer solar cells. In this work, based on the typical poly(3-hexylthiophene):[6,6]-phenyl C61-butyric acid methyl ester(P3HT:PCBM) polymer solar cell, we studied the effect of the cathode buffer layer(CBL) between the top metal electrode and the active layer on the device performance. Several inorganic and organic materials commonly used as the electron injection layer in an organic light-emitting diode(OLED) were employed as the CBL in the P3HT:PCBM polymer solar cells. Our results demonstrate that the inorganic and organic materials like Cs_2CO_3, bathophenanthroline(Bphen), and 8-hydroxyquinolatolithium(Liq) can be used as CBL to efficiently improve the device performance of the P3HT:PCBM polymer solar cells. The P3HT:PCBM devices employed various CBLs possess power conversion efficiencies(PCEs) of 3.0%–3.3%, which are ca. 50% improved compared to that of the device without CBL. Furthermore, by using the doped organic materials Bphen:Cs_2CO_3 and Bphen:Liq as the CBL, the PCE of the P3HT:PCBM device will be further improved to 3.5%, which is ca. 70% higher than that of the device without a CBL and ca. 10% increased compared with that of the devices with a neat inorganic or organic CBL.     

MoO3/Ag/AI/ZnO intermediate layer for inverted tandem polymer solar cells

We report an MoO3/Ag/Al/ZnO intermediate layer connecting two identical bulk heterojunction subcells with a poly（3-hexylthiophene） and [6,6]-phenyl-C61-butyric acid methyl ester （P3HT and PCBM） active layer for inverted tan- dem polymer solar cells. The highly transparent intermediate layer with an optimized thickness realizes an Ohmic contact between the two subcells for effective charge extraction and recombination. A maximum power conversion efficiency of 3.76% is obtained for the tandem cell under 100 mW/cm2 illumination, which is larger than that of a single cell （3.15%）. The open-circuit voltage of the tandem cell （1.18 V） approaches double that of the single cell （0.61 V）.     

MoO_3/Ag/Al/ZnO intermediate layer for inverted tandem polymer solar cells

We report an MoO3/Ag/Al/ZnO intermediate layer connecting two identical bulk heterojunction subcells with a poly(3-hexylthiophene) and [6,6]-phenyl-C61-butyric acid methyl ester(P3HT and PCBM) active layer for inverted tandem polymer solar cells. The highly transparent intermediate layer with an optimized thickness realizes an Ohmic contact between the two subcells for effective charge extraction and recombination. A maximum power conversion efficiency of 3.76% is obtained for the tandem cell under 100 mW/cm2 illumination, which is larger than that of a single cell(3.15%).The open-circuit voltage of the tandem cell(1.18 V) approaches double that of the single cell(0.61 V).