卟啉-二芳基乙烯分子的合成及其无损读取性能

二噻吩乙烯是一类性能优良的有机光致变色化合物,在信息储存领域具有广阔的应用前景,本文以2-甲基噻吩、苯甲醛和吡咯为原料,经过多步反应合成了1-(2-甲基-3-噻吩基)-2-{2-甲基-5-{4-[4-(10,15,20-三苯基-5-卟啉基)苯基]氨基羰基苯基}-3-噻吩基}环戊烯(DTE-TPP),其结构经核磁共振波谱仪(NMR)、质谱(MS)和傅里叶变换红外光谱仪(FTIR)表征确认,通过紫外-可见光谱研究了化合物的光致变色性能、抗疲劳性,并辅以荧光光谱探究了化合物的无损读取功能。结果表明,该化合物在254和660 nm的光照射下,发生可逆的光致变色反应,重复光照8次后其紫外-可见光谱与初始谱图相比无明显差异,显示出良好的抗疲劳性;当激发光为520 nm时,开、闭环异构体有较高的荧光对比度,有望实现数据的无损读取。     

静电陀螺仪MUM小角度读取的相关技术研究

讨论了同步解调法实现静电陀螺仪质量不平衡调制（MUM，Mass-Unbalanced Modulation）小角度读取的原理，分析了影响读取分辨率的各种因素，并对其实施方案中的相关技术进行了探讨。研究表明，尽管MUM读取方案非常适用于实心转子静电陀螺仪，但前提是将其小角度读取的分辨率提高到可与光电方法相比的水平（角秒级）。要实现这一目标，首先要保证转子和电极的机械特性达到一定要求；在此基础上，还要在支承系统的结构、转子位移测量电路设计等方面进行精心设计。     

A Resettable Keypad Lock with Visible Readout Based on Closed Bipolar Electrochemistry and Electrochromic Poly(3‐methylthiophene) Films

A closed bipolar electrode (BPE) system was developed with electrochromic poly(3‐methylthiophene) (PMT) films electropolymerized on the ITO/rGO electrode as one pole of BPE in the reporting reservoir and the bare ITO electrode as another pole of BPE in the analyte reservoir, in which rGO represents reduced graphene oxide. Under a suitable driving voltage (V_tot), the electrochemical reduction/oxidation of electroactive probes, such as H₂O₂/glutathione (Glu), in the analyte reservoir could induce the reversible color change of PMT films in the reporting reservoir between blue and red. Based on this, a keypad lock with H₂O₂, Glu, and V_tot=?3.0 V as the three inputs and the color change of PMT films as the visible output was established. This system was easily operated and did not need to synthesize the complex compounds or DNA molecules. The security system was easy to reset and could be used repeatedly.     

基于无基底焦平面阵列红外热像仪的理论模型分析

基于双材料微悬臂梁热变形原理的光学读出非制冷红外探测阵列经历了从有基底结构向无基底结构的发展过渡,无基底阵列的红外成像结果和有限元模型分析均表明无基底阵列不满足恒温基底条件.本文结合电学比拟的方法,提出了一种新的基于无基底焦平面阵列(focal plane Array,FPA)的热传递分析的理论模型.分析采用整体考虑的思路,避开了无基底FPA阵列各单元热传递互相影响所产生的复杂热分布分析,并考虑了框架对热量的吸收与传递.理论模型采用外边框与环境等温的边界条件,虽不及有限元方法对边界条件的处理灵活,但也已取 关键词： 光学读出 无基底 非制冷红外成像 焦平面阵列     

光机械式红外探测器中镜面弯曲对探测灵敏度的影响(英文)

光学读出式红外成像技术是近年来研究的热点,本文讨论了镜面弯曲对光学检测灵敏度的影响。由双材料微悬臂梁组成的非致冷焦平面阵列通过体刻蚀工艺加工而成,由于残余应力的影响,制成的焦平面阵列将会发生弯曲,应力导致的镜面弯曲将会降低光学探测灵敏度。本文通过傅立叶光学模拟了镜面弯曲对光学探测灵敏度的影响,并通过实验验证了该模型。实验和模拟结果表明,在镜面曲率为0 .1mm-1时,光学探测灵敏度将会降低到理想情况的40 %。最后我们用这个模型评价了通过表面修饰来提高光学性能的效果。     

An X-ray imaging device based on a GEM detector with delay-line readout

An X-ray imaging device based on a triple-GEM (Gas Electron Multiplier) detector, a fast delay-line circuit with 700 MHz cut-off frequency and two dimensional readout strips with 150 μm width on the top and 250 μm width on the bottom, is designed and tested. The localization information is derived from the propagation time of the induced signals on the readout strips. This device has a good spatial resolution of 150 μm and works stably at an intensity of 105 Hz/mm2 with 8 keV X-rays.     

Fabrication and characterization of ultra-low noise narrow and wide band Josephson parametric amplifiers

We have fabricated two types of lumped-element Josephson parameter amplifiers (JPAs) by using a multilayer micro-fabrication process involving wet etching of Al films. The first type is a narrow band JPA which shows typical gain above 14 dB in a bandwidth around 35 MHz. The second type is a wideband JPA which is coupled to an input 50 Ω transmission line via an impedance transformer that changes the impedance from about 15 Ω on the non-linear resonator side to 50 Ω on the input transmission line side. The wideband JPA could operate in a 200 MHz range with a gain higher than 14 dB. The amplifiers were used for superconducting qubit readout. The results showed that the signal to noise ratio and hence the readout fidelity were improved significantly.     

Design of the readout electronics for the DAMPE Silicon Tracker detector

The Silicon Tracker (STK) is one of the detectors of the DAMPE satellite used to measure the incidence direction of high energy cosmic rays. It consists of 6 X-Y double layers of silicon micro-strip detectors with 73728 readout channels. It is a great challenge to read out the channels and process the huge volume of data in the harsh environment of space. 1152 Application Specific Integrated Circuits (ASIC) and 384 ADCs are used to read out the detector channels. 192 Tracker Front-end Hybrid (TFH) modules and 8 identical Tracker Readout Board (TRB) modules are designed to control and digitalize the front signals. In this paper, the design of the readout electronics for the STK and its performance are presented in detail.     

A data transmission method for particle physics experiments based on Ethernet physical layer

Due to its advantages of universality, flexibility and high performance, fast Ethernet is widely used in readout system design for modern particle physics experiments. However, Ethernet is usually used together with the TCP/IP protocol stack, which makes it difficult to implement readout systems because designers have to use the operating system to process this protocol. Furthermore, TCP/IP degrades the transmission efficiency and real-time performance. To maximize the performance of Ethernet in physics experiment applications, a data readout method based on the physical layer(PHY) is proposed. In this method, TCP/IP is replaced with a customized and simple protocol, which makes it easier to implement. On each readout module, data from the front-end electronics is first fed into an FPGA for protocol processing and then sent out to a PHY chip controlled by this FPGA for transmission.This kind of data path is fully implemented by hardware. From the side of the data acquisition system(DAQ),however, the absence of a standard protocol causes problems for the network related applications. To solve this problem, in the operating system kernel space, data received by the network interface card is redirected from the traditional flow to a specified memory space by a customized program. This memory space can easily be accessed by applications in user space. For the purpose of verification, a prototype system has been designed and implemented.Preliminary test results show that this method can meet the requirements of data transmission from the readout module to the DAQ with an efficient and simple manner.     

Study of readout and cross-talks for multi-strip RPC with PSpice simulation

An electrical model for multi-strip resistive plate chamber (RPC) is presented, and a comparison between simulation results and test data is carried on. Based on the model, the influences of the RPC's design parameters on the readout are studied with PSpice simulation. Cross-talk (CT) phenomenon is observed and the relative amplitudes of the CT are studied for different design parameters.