Facile and Mild Synthesis and Characterization of Some New Diazo Dyes on the Basis of Schiff Bases in the Presence of Nanocrystalline Magnesium Oxide as a Base Catalyst under Solvent‐free Conditions

In this research, some new diazo dyes including Schiff base have been synthesized by the condensation reaction between ethylenediamine and derivatives of salicylaldehyde containing diazo functional groups in the presence of nanocrystalline magnesium oxide as a solid base catalyst under solvent‐free conditions. Nanocrystalline magnesium oxide has been characterized by XRD, BJH and TEM techniques. The corresponding products have been obtained in excellent yields and high purity. All of the obtained diazo‐Schiff bases are highly colored and can be applicable as useful diazo dyes and characterized by spectroscopy data.     

Elongated hexagonal ZnO micro-fence optical resonator

A highly symmetric ZnO micro-fence is prepared to form an optical resonator, which a symmetric array consisting of six elongated hexagonal microcolumns. It is found that the luminescence emission could be enhanced at the edge of ZnO micro-fence and the wavelength dependent light intensity could be influenced by its geometry. The optical characterization along with theoretical calculations and computer simulation analysis suggest that the Fabry-Perot and Cross-whispering gallery modes are generated in ZnO micro-fence. The individual ZnO micro-fence can regarded as an optical resonator structure. Furthermore, it is proposed that the source concentration around the substrate during the growth is a crucial factor for forming such a micro-fence.     

Geometric dynamic recrystallization of austenitic stainless steel through linear plane-strain machining

ABSTRACT

Type 316L austenitic stainless steel was severely plastically deformed at room temperature using linear plane-strain machining in a single pass that imparted shear strains up to 2.2 at strain rates up to 2?×?10³ s^?1. The resulting microstructures exhibited significant grain size refinement and improved mechanical strength where geometric dynamic recrystallization was identified as the primary microstructural recrystallization mechanism active at high strain rates. This mechanism is rarely observed in low to medium stacking fault energy materials. The critical stress required for twin initiation is raised by the combined effects of refined grain size and the increase in stacking fault energy due to the adiabatic heating of the chip, thus permitting geometric dynamic recrystallization. The suppression of martensite formation was observed and is correlated to the significant adiabatic heating and mechanical stabilisation of the austenitic stainless steel. A gradient of the amount of strain induced martensite formed from the surface towards the interior of the chip. As the strain rate is increased from 4?×?10² s^?1–2?×?10³ s^?1, a grain morphology change was observed from a population of grains with a high fraction of irregular shaped grains to one dominated by elongated grain shapes with a microstructure characterised by an enhanced density of intragranular sub-cell structure, serrated grain boundaries, and no observable twins. As strain rates were increased, the combination of reduction in strain induced martensite and non-uniform intragranular strain led to grain softening where a Hall-Petch relationship was observed with a negative strengthening coefficient of ?0.08?MPa m^1/2.     

ZIF‐8‐Nanocrystalline Zirconosilicate Integrated Porous Material for the Activation and Utilization of CO2 in Insertion Reactions

The conversion of CO₂ to useful chemicals, especially to atom economical products, is the best approach to utilize an excess of CO₂ present in the atmosphere. In this study, a metal‐organic framework (ZIF‐8) is integrated with nanocrystalline zirconosilicate zeolite to develop an integrated porous catalyst for CO₂ insertion reactions. The catalyst exhibits excellent activity for the CO₂ insertion reaction of epoxide to produce cyclic carbonate in neat condition without the addition of any co‐catalyst. The catalyst is stable and recyclable during the cyclic carbonate synthesis. Further, the catalyst also exhibits very good activity in another CO₂ insertion reaction to produce quinazoline‐2,4(1H, 3H)‐dione.     

Synthesis and characterization of thermoluminescent Li2B4O7 nanophosphor

Lithium borate (Li₂B₄O₇) is a low Z_eff, tissue equivalent material that is commonly used for medical dosimetry using the thermoluminescence (TL) technique. Nanocrystals of lithium borate were synthesized by the combustion method for the first time in the laboratory. TL characteristics of the synthesized material were studied and compared with those of commercially available microcrystalline Li₂B₄O₇. The optimum pre-irradiation annealing condition was found to be 300 °C for 10 min and that of post-irradiation annealing was 300 °C for 30 min. The synthesized Li₂B₄O₇ nanophosphor has very poor sensitivity for low doses of gamma up to 10¹ Gy whereas from 10¹ to 4.5×10² Gy this phosphor exhibits a linear response and then from 4.5×10² to 10³ Gy it shows supralinearity. Thermoluminescence properties of Li₂B₄O₇ nanophosphor doped with Cu has also been investigated in this paper. It shows low fading and a linear response over a wide range of gamma radiation from 1×10² to 5×10³ Gy. Therefore the synthesized lithium borate nanophosphor doped with Cu may be used for high dose measurements of gamma radiations.     

Electrodeposition of nanocrystalline Zn-Ni alloy from alkaline glycinate bath containing saccharin as additive

Nanocrystalline Zn-Ni (crystallite sizes 13-68 nm) alloy coatings were produced from an alkaline glycinate bath containing saccharin as additive. X-ray diffraction (XRD) was used to determine the phase composition and average crystallite size of nanocrystalline Zn-Ni alloy coatings. The average grain size of a deposit was also studied by transmission electron microscopy (TEM). The effects of saccharin concentration and current density on the crystallite size and surface roughness of the coatings were studied. Crystallite size and average surface roughness were diminished as a result of increasing saccharin concentration. Scanning electron microscopy (SEM) examination showed that coatings had a colony-like morphology and the colony size was increased with increasing current density. Microhardness testing was carried out in order to determine the degree of dependence of this mechanical property on the crystallite size. It was found that microhardness did not depend on crystallite size (Hall-Petch).     

Novel fabrication of net-like and flake-like Fe doped TiO2 thin films

New morphologies of net-like and flake-like TiO₂ thin films with different concentrations of Fe dopant were successfully fabricated by micro-arc oxidation (MAO) process of Ti plates and a subsequent chemical treatment of the as-prepared MAO-TiO₂ thin films. It was found that Fe ions can be easily introduced into the MAO-TiO₂ samples with the increase concentration of K₄(FeCN)₆·3H₂O precursor, and the amount of Fe determined the morphologies of TiO₂ thin films after chemical treatment; net-like morphology was observed with low Fe dopant, while it transformed to a flake-like one when Fe exceeds 1.7 at.%. UV-vis spectroscopy test showed that the absorption edge of the Fe ions doped TiO₂ thin films with new morphologies has an obvious red shift.     

Modulation of residual stress in diamond like carbon films with incorporation of nanocrystalline gold

Residual stress modulation in the diamond-like carbon coatings with incorporation of gold nanoparticles was studied critically. The films were deposited on glass and Si (1 0 0) substrates by using capacitatively coupled plasma chemical vapor deposition. Stresses in the films were determined from the broadening of the optical absorption tail and were found to decrease from 2.3 GPa to 0.48 GPa with increasing gold content (2-7 at.% Au) in the DLC matrix. Gold incorporation also made the films harder than the corresponding DLC coatings. Modulation of stress with nanocrystalline gold content in the DLC matrix was related to the relative amount of sp²/sp³ content in the DLC films.     

Sensing of LPG with nanostructured zinc oxide thin films grown by spray pyrolysis technique

Nanostructured zinc oxide thin films were prepared by spray pyrolysis technique using Zn(NO₃)₂·6H₂O as the precursor solution. The resulting films were investigated by X-ray diffraction and scanning electron microscopy to know crystal structure, size of crystallites and surface morphology. The films have been found to be polycrystalline zinc oxide, possessing hexagonal wurtzite crystal structure and nanocrystallite with grain size of approximately 30-35 nm. The LPG sensing performance of the films has been investigated at various concentrations of LPG in air at operating temperatures varying from 225 to 400 °C. At 325 °C the maximum responses of 46.3% and 48.9% have been observed, respectively, for concentrations of 0.8 and 1 vol% of LPG in air (1 vol% of LPG in air corresponds to 50% LEL of LPG in air). The recovery time has been found to be less than the response time for all concentrations of LPG. A possible reaction mechanism of LPG sensing has been proposed.     

Effect of substitution of K ions on the structural and electrical properties of nanocrystalline MgAl2O4 spinel oxide

Potassium substituted nanosized magnesium aluminates having a nominal composition Mg_1−xK_xAl₂O₄ where x=0.0, 0.25, 0.5, 0.75, 1.0 have been synthesized by the chemical co-precipitation method. The samples have been characterized by means of X-ray diffraction (XRD), scanning electron microscope (SEM), and dc electrical resistivity measurements. The XRD results reveal that the samples are spinel single phase cubic close packed crystalline materials. The calculated crystallite size ranges between 6 and 8 nm. The behaviour of the lattice constant seems to deviate from the Vegard's law. While X-ray density clearly increases, the bulk density and consequently, the percentage porosity do not exhibit a significant change on increasing the K⁺ content. The SEM micrographs suggest homogeneous distribution of the nanocrystallites in the samples. The dc electrical resistivity exhibits a typical semiconducting behaviour. Substitution of a Mg²⁺ ion by a K⁺ ion provides an extra hole to the system, which forms small polaron. Thermally activated hopping of these small polarons is believed to be the conduction mechanism in the Mg_1−xK_xAl₂O₄. The activation energy of hopping of small polarons has been calculated and found K⁺ ions content dependent.