基于SVM的固化土无侧限抗压强度模型

为实现较少试验次数下固化土无侧限抗压强度(qu)的准确预测, 提出了基于支持向量机(SVM)的固化土qu的预测模型. 以固化剂各组分掺入比、龄期、初始含水量、固化剂掺量等因素为输入量, 固化土的qu作为输出量, 以径向基为核函数, 采用网格搜索法和交叉验证法进行参数优化, 建立了基于SVM的固化土qu的预测模型. 算例分析表明: 该模型适用于任意条件下固化土qu的精确预测, 且在较小试验成本下实现与响应面法相当的预测精度.     

Infrared thermographic evaluation of large composite grid parts subjected to axial loading

Many composite parts, such as laminated panels and grid-like shells, operate under high mechanical loading. Evaluation of their structural integrity is crucial to ensure the long-lasting operation of critical components. Since testing a structure under full or “proof” load might be dangerous for personnel, it would be preferable to use a remote, rapid inspection technique. This paper describes a practical application of IR thermography to the inspection of large composite parts used in the aerospace industry. This work has used just one cycle of increasing load from zero load to failure, and this was done for both for tensile and compressive loads. It is shown that, during the formation of micro-defects in polymeric composites, about 40 % of the total dissipated energy is expended for material heating, while about 60 % is related to material damage accompanied by an increase in the defect concentration. Non-uniform composite deformation causes temperature anomalies, whose amplitude may reach 1.5–2.5 °C at a load of about 50–60 % of the limit load.     

Influence of metal electrodes on c‐axis orientation of AlN thin films deposited by DC magnetron sputtering

Nanocrystalline aluminum nitride (AlN) thin films were deposited on two types of metallic seed layers on silicon substrates, (111) textured Pt and (110) Mo, by reactive DC magnetron sputtering at low temperature (200 °C). Both textured films of Pt and Mo promote nucleation, thereby improving the crystallinity and epitaxial growth condition for AlN thin films. The deposited films were examined by X‐ray diffraction, scanning electron microscopy and atomic force microscopy techniques. The results indicated that the preferred orientation of crystallites greatly depends upon the kinetic energy of the sputtered species (target power) and seed layers used. Furthermore, AlN thin films with c‐axis perpendicular to the substrate grew on both types of metal electrodes at all power levels larger than 100 W. By comparing the structural properties and compressive stresses at perfect c‐axis orientation conditions, it is evident that AlN films deposited on (110) oriented Mo substrates exhibited superior properties as compared with Pt/Ti seed layers. Furthermore, less values of compressive stresses (?3 GPa) as compared with Pt/Ti substrates (?7.08 GPa) make Mo preferentially better candidate to be employed in the field of suspended Micro/Nano ‐ electromechanical systems (MEMS/NEMS) for piezoelectric devices. Copyright © 2017 John Wiley & Sons, Ltd.     

钢筋混凝土轴心受压构件的非线性稳定性

采用我国混凝土规范GB50010-2002规定的混凝土应力一应变关系,考虑混凝土强度、构件长细比及混凝土徐变,从构件的非线性理论出发对钢筋混凝土轴心受压构件的承载力进行了研究,给出了混凝土构件临界状态时的构件边缘应变和纵向弯曲系数的计算公式。研究表明,徐变对轴心受压构件的承载力有很大影响。当不考虑混凝土徐变时,按本文公...     

软土地区人工冻土无侧限瞬时抗压强度的试验研究

冻结法施工在上海隧道建设中(如隧道旁通道、地下泵房等的设计与施工)得到广泛应用,也曾引发过严重的地质灾害(如上海地铁4号线外滩段的地质灾害)。因此安全、经济、合理地将冻结法用于上海软土地区隧道建设中已经成为上海工程建设中的一个重要的研究课题。本文以上海复兴东路越江隧道旁通道冻结法施工中遇到的第⑥层粉质粘土及第⑦层粉细砂为研究对象,针对设计冻结壁重要强度参数无侧限瞬时抗压强度,进行了室内试验研究,揭示了两种土的冻结强度随温度的变化关系,同时研究了粉细砂的冻结强度随含水率的变化规律。     

TNT炸药动静态变温三轴压缩力学性能的试验研究

介绍了一种高能材料动静态变温三轴压缩试验装置，在熔点以下温度，通过对国产单质炸药ＴＮＴ在中等应变速率（２－４／ｓ）及准静态（３×１０－３／ｓ）条件下三轴压缩力学性能的测试，得出ＴＮＴ的杨氏模量Ｅ、泊松比ν和屈服极限Ｙ，以及当加载速率和温度改变时这些参数的变化规律。并提出三轴应力状态下屈服极限的一种确定方法。该三轴压缩试验装置以及三轴压缩应力状态下力学参数的测试、分析、处理系统为研究高能材料力学性能提供了一套完整的技术和手段。     

Elastoplastic Axisymmetric Stress-Strain State of Laminated Shells Made of Isotropic and Transversely Isotropic Materials with Different Moduli

A method is developed for analysis of the elastoplastic stress-strain state of laminated shells of revolution under axisymmetric loading. The shells are made of isotropic and transversally isotropic materials with different moduli. The method is based on the Kirchhoff-Love hypotheses for the whole laminate, the theory of deformation along paths of small curvature (for isotropic materials), and the theory of elasticity with different tensile and compressive moduli (transversely isotropic materials). The problem is solved by the method of successive approximations. Numerical examples are given __________ Translated from Prikladnaya Mekhanika, Vol. 41, No. 8, pp. 88–96, August 2005.     

Effect of a Nanoclay on the Mechanical,Thermal and Flame Retardant Properties of Rigid Polyurethane Foam

Water blown rigid polyurethane foams (PUF) with organoclay/organically modified nanoclay (ONC) were prepared and their properties such as density, mechanical, morphological, insulation, thermal and flame retardant properties were studied. In this investigation, the ONC content was varied from 1 to 10 parts per hundred of polyol (php) by weight. It was observed that the compressive strength of ONC filled PUF increased up to 3 php of ONC loading and then it decreased. Wide angle X-ray diffraction and transmission electron microscopy studies indicated the exfoliated dispersion of ONC in PUF. The thermal conductivity of ONC filled PUF decreases up to 5 php and then increases. The glass transition temperature (Tg) of PUF decreases on loading of ONC. The TGA analysis shows that there is slight increase in degradation temperature with increase in ONC loading. The flame retardant properties (LOI and flame spread rate) are improved slightly on addition (3 php) of ONC filled PUF.     

Experimental Evaluation of Undersampling Schemes for Electron Tomography of Nanoparticles

One of the emerging challenges in the field of 3D characterization of nanoparticles by electron tomography is to avoid degradation and deformation of the samples during the acquisition of a tilt series. In order to reduce the required electron dose, various undersampling approaches have been proposed. These methods include lowering the number of 2D projection images, reducing the probe current during the acquisition, and scanning a smaller number of pixels in the 2D images. A comparison is made between these approaches based on tilt series acquired for a gold nanoparticle.     

HTPB复合底排药压缩屈服应力模型研究

目前广泛应用于底排增程技术的 HTPB 复合底排药 (composite base bleed grain,CBBG) 是一种颗粒填充含能材料,战场环境中将承受冲击、温度等载荷作用. 为研究 HTPB CBBG 冲击压缩力学性能,进行了不同温度 (233$\sim$323 K) 和应变率 (1100$\sim$7900 s$^{-1}$) 下的分离式霍普金森压杆实验. 实验结果表明,各工况下,应力应变曲线均呈现屈服-$\!$-应变硬化特征,HTPB CBBG 保持高韧性. 提高应变率和降低温度均导致相同应变下的应力幅值上升,但温度较应变率对HTPB CBBG 冲击压缩力学性能的影响更为显著. 基于所研究温度范围高于 HTPB CBBG 玻璃化转变温度,通过将水平、垂直移位因子与温度的关系表示为 WLF 方程的形式,将时温等效原理引入协同模型,并计及内应力的应变率增强效应,提出了一种新的屈服应力模型.选取参考温度,利用水平、垂直移位因子-$\!$-温度曲线和屈服应力主曲线拟合模型参数.模型预测值与实验数据对比结果表明:该模型可准确表征 233$\sim$323 K 时 HTPB CBBG 屈服应力的双线性应变率相关性,明确了较低和较高应变率时,应变率效应分别主要由内应力和驱动力贡献.