Interface and defects engineering for multilayer laser coatings

High-reflective multilayer laser coatings are widely used in advanced optical systems from high power laser facilities to high precision metrology systems. However, the real interface quality and defects will significantly affect absorption/scattering losses and laser induced damage thresholds of multilayer coatings. With the recent advances in the control of coating design and deposition processes, these coating properties can be significantly improved when properly engineered the interface and defects. This paper reviews the recent progress in the physics of laser damage, optical losses and environmental stability involved in multilayer reflective coatings for high power nanosecond near-infrared lasers. We first provide an overview of the layer growth mechanisms, ways to control the microstructures and reduce layer roughness, as well as the nature of defects which are critical to the optical loss and laser induced damage. Then an overview of interface engineering based on the design of coating structure and the regulation of deposition materials reveals their ability to improve the laser induced damage threshold, reduce the backscattering, and realize the desirable properties of environmental stability and exceptional multifunctionality. Moreover, we describe the recent progress in the laser damage and scattering mechanism of nodule defects and give the approaches to suppress the defect-induced damage and scattering of the multilayer laser coatings. Finally, the present challenges and limitations of high-performance multilayer laser coatings are highlighted, along with the comments on likely trends in future.     

Defects related emission and nanosecond optical power limiting in CuS quantum dots

We report optical and nonlinear optical properties of CuS quantum dots and nanoparticles prepared through a nontoxic, green, one-pot synthesis method. The presence of surface states and defects in the quantum dots are evident from the luminescent behavior and enhanced nonlinear optical properties measured using the open aperture Z-scan, employing 5 ns laser pulses at 532 nm. The quantum dots exhibit large effective third order nonlinear optical coefficients with a relatively lower optical limiting threshold of 2.3 J cm⁻², and the optical nonlinearity arises largely from absorption saturation and excited state absorption. Results suggest that these materials are potential candidates for designing efficient optical limiters with applications in laser safety devices.     

Curvature investigation in tapered fibers and its application to sensing and mode conversion

Non-adiabatic tapered fibers are basic photonic components used in a wide range of applications. Here we investigate a way to increase their utility through the controllable bending of one of their tapered sections. The experiments carried out explain, for the first time, the mechanics of this approach showing how these tapers can be used to build more sensitive sensors. Their use as highly efficient mode converters is also discussed.     

TBOR-shaped electro-optic modulator with dual output based on double-layer graphene

We proposed an electro-optic modulator with two-bus one-ring (TBOR) structure to improve the extinction ratio and reduce insert loss. It has a dual output compared with one-bus one-ring structure. In addition, double-layer graphene makes it possible for the modulation in the visible to mid-infrared wavelength range. It shows that this new electro-optic modulator can present two switching states well with low insertion loss, high absorption and high extinction ratio. At $\lambda =1550\text{ nm}$, when the switching states are based on the chemical potential, ${\mu }_{\mathrm{c}}=0.38\text{ eV}$ and ${\mu }_{\mathrm{c}}=0.4\text{ eV}$, the insertion losses of both output ports are less than 2 dB, the absorption of the output port coupled via a micro-ring reaches 45 dB and the extinction ratio reaches 14 dB. When the refractive index of the dielectric material is 4.2, the applied voltage will be less than 1.2 V, thus can be used in low-voltage CMOS technology.     

Crosslinked poly(ethylene oxide) containing siloxanes fabricated through thiol‐ene photochemistry

Homogenous amphiphilic crosslinked polymer films comprising of poly(ethylene oxide) and polysiloxane were synthesized utilizing thiol‐ene “ click ” photochemistry. A systematic variation in polymer composition was Carried out to obtain high quality films with varied amount of siloxane and poly(ethylene oxide). These films showed improved gas separation performance with high gas permeabilities with good CO₂/N₂ selectivity. Furthermore, the resulting films were also tested for its biocompatibility, as a carrier media which allow human adult mesenchymal stem cells to retain their capacity for osteoblastic differentiation after transplantation. The obtained crosslinked films were characterized using differential scanning calorimetry, dynamic mechanical analysis, thermogravimetric analysis, FTIR, Raman‐IR , and small angle X‐ray scattering. The synthesis ease and commercial availability of the starting materials suggests that these new crosslinked polymer networks could find applications in wide range of applications. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1548–1557     

油-气-水三相流超声传感器持气率测量*

为探索油-气-水三相流持气率测量难题,该文开展了脉冲透射式超声传感器持气率测量动态实验研究。首先,利用超声传感器与光纤传感器组合,测取了油-气-水三相流中段塞流、混状流、泡状流的响应信号;其次,提取了超声脉冲信号的最大值序列来反映不同流型时超声传感器响应特性,同时,借助双头光纤传感器与相关测速法,计算得到了流体中气泡弦长序列;最后,结合流型与泡径信息,利用超声传感器测量了不同流型下持气率,并分析了不同流型持气率预测的误差来源,为其他油-气-水三相流持气率测量传感器设计提供了借鉴。     

Influence of solvent on solution processed Cu2ZnSnS4 nanocrystals and annealing induced changes in the optical,structural properties of CZTS film

The well-known quaternary Cu₂ZnSnS₄ (CZTS) chalcogenide thin films are playing an important role in modern technology. The CZTS nanocrystal were successfully prepared by solution method using water, ethylene glycol and ethylenediamine as different solvent. The pure phase material was used for thin film coating by thermal evaporation method. The prepared CZTS thin films were characterized by XRD, Raman spectroscopy, FESEM, XPS and FT-IR spectroscopy. The XRD and Raman spectroscopy analysis revealed the formation of polycrystalline CZTS thin film with tetragonal crystal structure after annealing at 450 ^°C. The oxidation state of the annealed film was studied by XPS. A direct band gap about 1.36 eV was estimated for the film from FT-IR studies, which is nearly close to the optimum value of band gap energy of CZTS materials for best solar cell efficiency. The CZTS annealed thin films are more suitable for using as a p-type absorber layer in a low-cost solar cell.     

Controlled synthesis of ZnO nanoparticles from a Zn(II) coordination polymer: Structural characterization,optical properties and photocatalytic activity

A zinc coordination polymer derived from pyridine-2,6-dicarboxylate (PDC), {[Zn₂(PDC)₂]}_n, was successfully prepared via conventional, sonication and microwave-irradiation methods. The composition and characteristics of the obtained coordination polymers (CPs) were investigated by elemental analysis, TGA/DTA, X-ray diffraction and spectroscopic techniques. The so obtained CPs were heat-treated in the air at 600 °C for 2 h to produce ZnO of nanosized particles (NPs). It is of interest to note that the synthesis approach of the precursor greatly affects both the nanoparticle size and the structure of the resulting ZnO NPs. Moreover, the smallest particle size was associated with the sample derived from the ultrasonically prepared precursor. TEM analysis revealed that all samples have sphere-like morphologies. Structural analysis of the prepared ZnO samples was conducted and compared using Rietveld analysis of their PXRD patterns. Optical band gap calculations based on analysis of the UV–vis spectra of ZnO samples using Tauc's power law were achieved. The highest band gap of 3.63 eV was observed for ZnO sample obtained from the ultrasonically prepared precursor. Furthermore, the photocatalytic activity of ZnO NPs for the removal of Eosin Y color was monitored. The highest removal efficiency was recorded for ZnO originated from the ultrasonically synthesized precursor. Enhancement of removal efficiency that reached 98% was attained in only a period of 8 min. Its recycling test showed that it can be reused without structural changes over four cycling experiments.     

Preparation and Characterization of Activated Carbon from Microwave and Conventional Heated Almond Shells Using Phosphoric Acid Activation

Activated carbon production from almond shells using phosphoric acid activation agent was achieved by applying both conventional heating and microwave heating in succession. The morphology and surface properties of activated carbon were studied using thermogravimetric and differential gravimetric analysis, Fourier-transform infrared spectroscopy, scanning electron microscopy, and Brunauer–Emmett–Teller analysis. A surface area of 1128 m²/g was achieved by optimizing the microwave power (500?W), microwave application time (15?minutes), conventional heating time (45?minutes), conventional heating temperature (500?°C), and the phosphoric acid:sample ratio (0.7:1). An adsorption capacity of methylene blue of 148?mg/g and an iodine value of 791?mg/g was obtained for the prepared activated carbon.     

非线性光纤方向耦合器孤子动力特性分析

利用变分方法,导出了双曲正割型光孤子在非线性光纤耦合器中传输时满足的动力学方程组,分析了该方程组的平衡点性态,讨论了光孤子的开关特性.指出参数|β|<2π.是能实现完全的开关操作的必要条件.