用等厚干涉测定液体折射率

介绍一种采用等厚干涉原理测定液体折射率的简单可靠的方法。     

宽带膜厚实时监控过程中膜层折射率的确定方法

为了准确计算出镀膜过程中每层膜的折射率，介绍了实时监控过程中确定膜层折射率的2种方法：一种是由实测的透射比光谱直接反算出膜层的折射率；另一种是用最小二乘法的优化算法实时拟合折射率。试验结果表明：在线反算适合单点监控，所得折射率误差小于2%。然而在实际镀膜过程中,由于宽带内膜层参数误差较大,一般大于25%。为此，采用最小二乘法拟合，即在整个宽光谱范围内采集每个波长点的信息，所得结果误差很小，一般都在2％～5%之间,有时可达到10%,在很大程度上提高了实际镀膜时膜厚监控的精度。     

厚度对非极性聚合物薄膜驻极体电荷储存及电荷动态特性的影响

以Du Pont公司的商用Teflon FEP A型薄膜为例，通过热脉冲技术、等温表面电位衰减测量和开路热刺激放电电流谱分析等实验结果，讨论了经常温和高温电晕充电后样品厚度对薄膜驻极体的沉积电荷密度、薄膜驻极体的内电场、体电导率以及电荷储存稳定性的影响.通过热脉冲技术组合电导率温度曲线的测量，研究了在不同温度条件下样品厚度对沉积电荷层的平均电荷重心移动的影响.结果表明：在充电参数一定的条件下，随着膜厚的降低，储存电荷密度上升，但电荷稳定性有所下降.因此，合理地调控薄膜厚度，可以有效地优化驻极体的电荷储存能 关键词： 厚度 驻极体 电荷储存能力 电荷稳定性     

摄像型等厚干涉实验仪器的研究

介绍了“摄像型等厚干涉实验仪”的构造及等厚干涉实验新的测量方法。     

An approximate solution to the integral radiative transfer equation in an optically thick slab

We consider the problem of solving the integral form of the radiative transfer equation in an atmosphere with optical thickness τ₀?1. We propose two methods transforming this problem to a finite set of the independent problems of the same type set in an atmosphere with optical thickness much less then τ₀. The error estimates are derived. Copyright © 2007 John Wiley & Sons, Ltd.     

用^60Co放射源检测油垢厚度的初步实验研究

本文用石蜡模拟油垢，用^60Co放射源的1．25MeV平均能量的γ射线垂直入射，以一定的散射角和不同的探测立体角接收散射γ光子敫．发现散射γ计数与被测石蜡厚度之间存在不同的线性关系．结果发现，放射源与探测器之间屏蔽的好坏和合理的探测距离对提高线性度有很大关系．本实验测得最佳线性相关系数平方值为0．9981，平均测量精度为1．26mm．这对研究散射法检测油垢厚度和选择合适的探测距离提供了实验基础．     

Atomistic phenomena in dense fluid shock waves

The shock structure problem is one of the classical problems of fluid mechanics and at least for non-reacting dilute gases it has been considered essentially solved. Here we present a few recent findings, to show that this is not the case. There are still new physical effects to be discovered provided that the numerical technique is general enough to not rule them out a priori. While the results have been obtained for dense fluids, some of the effects might also be observable for shocks in dilute gases.     

Phase Measurement Algorithm in Wavelength Scanned Fizeau Interferometer

Wavelength scanned interferometry allows the simultaneous measurement of top surface shape and optical thickness variation of a transparent object consisting of several parallel surfaces. Interference signals from these surfaces can be separated in frequency space, and their phases are detected by discrete Fourier analysis. However, these signal frequencies are shifted from the detection frequency by the refractive index dispersion of the object and a nonlinearity of the wavelength scanning. The Fourier analysis is sensitive to the detuning of the signal frequency and suffers from the multiple-beam interference noise. Conventional error-compensating algorithms cannot be applied to an object consisting of more than three reflecting surfaces. We derive a new 2N-1 sample error-compensating algorithm, which allows the phase detection of any order of harmonic frequency among the interference signals. The new algorithm suppresses the effect of signal frequency detuning as well as the multiple-beam interference noise and can be applied to the measurement of complex objects consisting of more than three reflecting surfaces.     

ICF靶丸中液氢层厚度的确定

 利用靶丸内部的质量守恒，提出了计算惯性约束聚变靶丸内液氢层厚度的函数关系式，从而得到了求解惯性约束聚变靶丸内液氢层厚度的一般模型，并在此基础上对影响液氢层厚度的各类因素如温度、充气密度等进行了讨论。该模型的分析方法同样适用于惯性约束聚变中的燃料气体氘、氚或者氘氚混合物。     

An evolutionary method for optimization of plate buckling resistance

Optimization of plate buckling resistance is very complicated, because the in-plane stress resultants in the prebuckled state of a plate are functions of thickness distribution. This paper discusses the problem of finding the optimum thickness distribution of isotropic plate structures, with a given volume and layout, that would maximise the buckling load. A simple numerical method using the finite-element analysis is presented to obtain the optimum thickness distribution. Optimum designs of compression-loaded rectangular plates with different boundary conditions and plate aspect ratios are obtained by using the proposed method. Optimum designs from earlier studies and the methods of buckling analysis used to attain these results are discussed and compared with the designs from the proposed method. This paper also examines the reliability of the optimality criterion generally used for plate buckling optimization, which is based on the uniform strain energy density.