Interface and defects engineering for multilayer laser coatings

High-reflective multilayer laser coatings are widely used in advanced optical systems from high power laser facilities to high precision metrology systems. However, the real interface quality and defects will significantly affect absorption/scattering losses and laser induced damage thresholds of multilayer coatings. With the recent advances in the control of coating design and deposition processes, these coating properties can be significantly improved when properly engineered the interface and defects. This paper reviews the recent progress in the physics of laser damage, optical losses and environmental stability involved in multilayer reflective coatings for high power nanosecond near-infrared lasers. We first provide an overview of the layer growth mechanisms, ways to control the microstructures and reduce layer roughness, as well as the nature of defects which are critical to the optical loss and laser induced damage. Then an overview of interface engineering based on the design of coating structure and the regulation of deposition materials reveals their ability to improve the laser induced damage threshold, reduce the backscattering, and realize the desirable properties of environmental stability and exceptional multifunctionality. Moreover, we describe the recent progress in the laser damage and scattering mechanism of nodule defects and give the approaches to suppress the defect-induced damage and scattering of the multilayer laser coatings. Finally, the present challenges and limitations of high-performance multilayer laser coatings are highlighted, along with the comments on likely trends in future.     

Strain induced strengthening of soft thermoplastic polyurethanes under cyclic deformation

We investigate the cyclic mechanical behavior in uniaxial tension of three different commercial thermoplastic polyurethane elastomers (TPU) often considered as a sustainable replacement for common filled elastomers. All TPU have similar hard segment contents and linear moduli but sensibly different large strain properties as shown by X-ray analysis. Despite these differences, we found a stiffening effect after conditioning in step cyclic loading which greatly differs from the common softening (also referred as Mullins effect) observed in chemically crosslinked filled rubbers. We propose that this self-reinforcement is related to the fragmentation of hard domains, naturally present in TPU, in smaller but more numerous sub-units that may act as new physical crosslinking points. The proposed stiffening mechanism is not dissimilar to the strain-induced crystallization observed in stretched natural rubber, but it presents a persistent nature. In particular, it may cause a local reinforcement where an inhomogeneous strain field is present, as is the case of a crack propagating in cyclic fatigue, providing a potential explanation for the well-known toughness and wear resistance of TPU.     

Scaling properties of fracture surfaces on glass strengthened by ionic exchange

In this work the results of the statistical topometric analysis of fracture surfaces of soda-lime-silica glass with and without ionic exchange treatment are reported. In this case, the mechanism of substitution is K⁺-Na⁺. atomic force microscopy (AFM) was employed to record the topometric data from the fracture surface. The roughness exponent (ζ) and the correlation length (ξ) were calculated by the variable bandwidth method. The analysis for both glasses (subjected and non-subjected to ionic exchange) for ζ shows a value ∼0.8, this value agrees well with that reported in the literature for rapid crack propagation in a variety of materials. The correlation length shows different values for each condition. These results, along with those of microhardness indentations suggest that the self-affine correlation length is influenced by the complex interactions of the stress field of microcracks with that resulting from the collective behavior of the point defects introduced by the strengthening mechanism of ionic exchange.     

单甲基原位改性SiO2疏水减反膜的制备与性能研究

 在碱性条件下通过TEOS和MTES的共水解缩聚反应制备了单甲基原位改性的SiO₂溶胶，并使用提拉法在K9玻璃基片上镀制了疏水减反膜。通过透射电镜（TEM）考察了镀膜溶胶的微结构，分别使用红外光谱（FTIR）分析了薄膜的组分，用原子力显微镜（AFM）观察了薄膜的表面形貌和起伏状况，用紫外可见光谱（UV-vis）考察了薄膜的减反射性能，用接触角仪测量了薄膜对水的接触角。并使用“R-on-1”的方式测量了薄膜在Nd:YAG激光（1 064 nm，1 ns）作用下的损伤阈值。结果表明，通过共水解缩聚反应可以把甲基引入镀膜溶胶簇团中，改善了溶胶簇团的网络结构，使薄膜得到相当好的疏水性能和更好的抗激光损伤性能，同时薄膜能保持较好的减反射性能。     

离子交换富集-导数火焰原子吸收法测定自来水中Cu,Fe和Zn

本文研究了用 2 0 1× 7阳离子交换树脂对自来水中的微量元素进行交换富集 ,采用微量脉冲进样 导数火焰原子吸收法测定富集后溶液中的Cu ,Fe和Zn ,该方法灵敏度分别为 0 2 9,0 5 9和 0 0 6 μg·L- 1 ,精密度分别为 4 2 8% ,1 95 %和 2 2 8% ,检测限分别为 1 2 8,5 85和 0 6 8μg·L- 1 ,回收率分别为 91 13% ,10 1 34%和99 84 % ,本方法大大减少了需样量 ,简便快速 ,灵敏度高。     

Laser-induced damage of Ta2O5/SiO2 narrow-band interference filters under different 1064 nm Nd:YAG laser modes

The laser-induced damage (LID) behavior of narrow-band interference filters was investigated with a Nd:YAG laser at 1064 nm under single-pulse mode and free-running mode. The absorption measurement of such coatings was performed with surface thermal lensing (STL) technique. The damage morphologies under the two different laser modes were also studied in detail. It was found that all the filters exhibited a pass-band-center-dependent absorption and laser-induced damage threshold (LIDT) behavior, but the damage morphologies were diverse. The explanation was given with the analysis of the electric field distribution and the operational behavior of the irradiation laser.     

A theoretical study of the ion pair SN2 reaction between lithium isocyanates with methyl fluoride with inversion and retention mechanism

This paper is devoted to a detailed theoretical study of an ion pair S_N2 reaction LiNCO+CH₃F in the gas phase and in solution at the level of MP2(full)/6-31+G**//HF/6-31+G**. Two possible reaction mechanisms, inversion and retention, are discussed. There are eight possible reaction pathways. The inversion mechanism is more favorable no matter in the gas phase or in solution based on analyses of the transition structures. Methyl isocyanate should form preferentially in the gas phase and more stable methyl cyanate is the main product in solution. The retardation of the reaction in solvents was attributed to the difference in solvation in the separated reactants and in the transition state.     

激光诱导间质肿瘤热疗的数值模拟和实验研究

本文在考虑生物组织物性动态变化的情况下建立了激光诱导间质肿瘤热疗(LITT)的物理数学模型,采用MonteCarlo方法数值模拟了LITT中激光能量在生物组织内的传输过程,基于Pennes生物传热方程和Arrhenius方程数值求解了组织内的温度分布和热损伤体积的变化,分析了热物性及血液灌注率的动态变化对LITT过程的影响,并与相应的离体实验结果进行了对比。数值模拟结果表明,组织的热物性及血液灌注率的动态变化对于热损伤体积的变化具有重要的影响。因此在激光诱导间质肿瘤热疗的数值模拟中应该考虑热物性及血液灌注率的动态变化以期为临床治疗方案的制定提供更为准确的依据。     

ns脉冲激光对K9玻璃的破坏实验

 采用高速PIN光电探测器和高带宽的数字存储示波器，实时检测透射光脉冲和散射光脉冲的变化特征，并将之用作材料破坏的光学判据，测量得到K9玻璃在1.06μm纳秒脉冲激光作用下的能量损伤阈值约18mJ，相应的能量密度阈值为1.0kJ/cm²。通过分析透射光脉冲和散射光脉冲的特征，给出了材料的破坏时刻，并推断出K9玻璃所能承受的极限光强为10¹⁵W/m²。研究了能量透过率与泵浦能量的关系，并初步探讨了透明材料的破坏机理。结果表明：在多纵模激光的作用下，透明光学材料破坏是电离击穿与自聚焦效应综合作用的结果。     

Adaptive remeshing for ductile fracture prediction in metal formingRemaillage adaptatif pour la prévision de la rupture ductile en mise en forme

The analysis of mechanical structures using the Finite Element Method in the framework of large elastoplastic strain, needs frequent remeshing of the deformed domain during computation. Indeed, the remeshing is due to the large geometrical distortion of finite elements and the adaptation to the physical behavior of the solution. This paper gives the necessary steps to remesh a mechanical structure during large elastoplastic deformations with damage. An important part of this process is constituted by geometrical and physical error estimates. The proposed method is integrated in a computational environment using the ABAQUS/Explicit solver and the BL2D-V2 adaptive mesher. To cite this article: H. Borouchaki et al., C. R. Mecanique 330 (2002) 709–716.