煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Can a Procedure for the Growth of Single-layer Graphene on Copper be used in Different Chemical Vapor Deposition Reactors?

In the last decade, catalytic chemical vapor deposition (CVD) has been intensively explored for the growth of single-layer graphene (SLG). Despite the scattering of guidelines and procedures, variables such as the surface texture/chemistry of catalyst metal foils, carbon feedstock, and growth process parameters have been well-scrutinized. Still, questions remain on how best to standardize the growth procedure. The possible correlation of procedures between different CVD setups is an example. Here, two thermal CVD reactors were explored to grow graphene on Cu foil. The design of these setups was entirely distinct, one being a “showerhead” cold-wall type, whereas the other represented the popular “tubular” hot-wall type. Upon standardizing the Cu foil surface, it was possible to develop a procedure for cm²-scale SLG growth that differed only by the carrier gas flow rate used in the two reactors.     

Facile non‐lithographic route to highly aligned silica nanopatterns using unidirectionally aligned polystyrene‐block‐polydimethylsiloxane films

Thin films (monolayer and bilayer) of cylinder forming polystyrene‐block‐polydimethylsiloxane (PS‐b‐PDMS) were shear aligned by the swelling and deswelling of a crosslinked PDMS pad that was physically adhered to the film during solvent vapor annealing. The nanostructures formed by self‐assembly were exposed to ultraviolet‐ozone to partially oxidize the PDMS, followed by calcination in air at 500 °C. In this process, the PS segments were fully decomposed, while the PDMS yielded silica nanostructures. The highly aligned PDMS cylinders were thus deposited as silica nanolines on the silicon substrate. Using a bilayer film, the center‐to‐center distance of these features were effectively halved from 38 to 19 nm. Similarly, by sequential shear‐alignment of two distinct layers, a rhombic array of silica nanolines was fabricated. This methodology provides a facile route to fabricating complex topographically patterned nanostructures. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1058–1064     

GaN氢化物气相外延生长系统的设计与制作

根据GaN氢化物气相外延生长(HVPE)的原理,设计制作了双温区卧式HVPE系统．根据实际生长中出现的问题和CaN样品的测试情况,对系统进行了逐步的调试和改进．     

Roles of SiH4 and SiF4 in growth and structural changes of poly-Si films

The structural properties of polycrystalline silicon films, prepared by plasma enhanced chemical vapor deposition system, with different flow rates of SiH₄/SiF₄ mixtures at 300 °C were investigated. This study indicates that the low hydrogen coverage on the growing surface, under optimum fluorine radicals, will be leaded to an improvement of crystallized area as compared with case of high hydrogen coverage surface. Moreover, the studies of the role of SiH₄ and SiF₄ radicals show that the SiH₄ radicals are important in the nucleation and growth of grains. However, SiF₄ radicals are effective in the structural change of grain boundaries regions and by this way, in the present system, establish the growth of grains under the dominant 〈1 1 0〉 direction. The stress investigation indicates that addition of high flow rate of SiF₄ in amorphous film, results in the nearly stress free films. Finally, we found that the changes in g-value reflect the changes in the intrinsic compressive and tensile stress in the both polycrystalline and amorphous silicon films.     

Electrical properties and Schottky diodes using N-N′diphenyl-1-4phenylenediamine

Thin films of, N-N′diphenyl 1-4phenylene-diamineane are prepared using vacuum sublimation technique. The electrical conductivity from room temperature down to 127 K is studied. It is found that the conduction of charge carriers obeys T^−1/2 dependence on temperature. The average hopping distance, hopping energy, density of states and their variation due to post-deposition heat treatment are studied. Schottky diodes are fabricated with gold as ohmic contact and aluminium as Schottky contact. From the observed current voltage characteristics the saturation current density, diode ideality factor and the barrier height are determined. Their variation with air annealing is also investigated.     

Magnetic properties of oxygenated carbon nitride films from RF-discharge in an acetylene, nitrogen, and oxygen mixture environments

Properties of oxygenated carbon nitride films have attracted the attention of physics researchers due to their magnetic and physical properties, as well as for their usefulness in the industry. The free radicals were investigated using electron paramagnetic resonance applied in the study of spin concentration due to the different mechanism of preparation of carbon nitride films by RF-discharge with different kinds of plasma. Unpaired spin concentrations, in the order of 10²⁰ per cm³, were measured and their time recombination dependency was important in those films. The films were grown by plasma enhanced chemical vapor deposition using mixtures of hydrocarbons, N₂ and O₂ in different proportions.     

Cosmic dust and our origins

The small solid particles in the space between the stars provide the surfaces for the production of many simple and complex molecules. Processes involving the effects of ultraviolet irradiation of the thin (hundredth micron) mantles are shown to produce a wide range of molecules and ions also seen in comets. Some of the more complex ones inferred from laboratory experiments are expected to play an important role in the origin of life. An outline of the chemical evolution of interstellar dust as observed and as studied in the laboratory is presented. Observations of comets are shown to provide substantial evidence for their being fluffy aggregates of interstellar dust as it was in the protosolar nebula, i.e. the interstellar cloud which collapsed to form the solar system. The theory that comets may have brought the progenitors of life to the earth is summarized.     

Laser induced copper electroless plating on polyimide with Q-switch Nd:YAG laser

The results of laser induced deposition of copper on polyimide substrate from copper electrolyte solution are reported. Unlike most work reported in the literatures where CW Ar⁺ lasers were used, a second harmonic (532 nm wavelength) Q-switch Nd:YAG laser was used for our experiments. The deposition process was conducted by laser-catalyzing of the polyimide surface and subsequent photothermal-accelerated reduction of copper-complex ions in an alkaline reducing environment. The characteristics of the deposited copper line were investigated in terms of laser beam scanning speed, and the number of scans. The surface morphology and chemical composition of the deposited copper were analyzed using field emission scanning electron microscope (FESEM) and energy dispersive spectrometer (EDX). The optimum processing conditions have been identified. The copper deposit was found to adhere well to the substrate.     

不同入射角度下强流脉冲电子束能量沉积剖面和束流传输系数模拟计算

 强流脉冲电子束在材料中的能量沉积剖面、能量沉积系数和束流传输系数受其入射角的影响很大，理论计算了0.5~2.0MeV的电子束以不同的入射角在Al材料中的能量沉积剖面和能量沉积系数，并且还计算了0.4~1.4MeV电子束以不同入射角穿透不同厚度C靶的束流传输系数。计算结果表明，随着入射角的增大，靶材表面层单位质量中沉积的能量增大，电子在靶材料中穿透深度减小，能量沉积系数减小，相应的束流传输系数也减小；能量为0.5~2.0MeV的电子束当入射角在60°~70°时在材料表面层单位质量中沉积的能量较大。