氯柱硼镁石在氯化镁水溶液中相转化平衡液相的红外光谱分析

采用差示FTIR光谱技术,研究了氯柱硼镁石在30℃下浓度为0.5,12和18％MgCl_2水溶液中溶解及相转化平衡饱和水溶液中硼氧配阴离子的FTIR光谱。给出了溶液中硼氧配阴离子的FTIR光谱振动频率的归属,515cm~(-1)为单和二硼氧配阴离子特征峰,630cm~(-1)为三硼氧配阴离子特征峰,550cm~(-1)为四硼氧配阴离子特征峰。对饱和水溶液中硼氧配阴离子的存在形式及其相互作用以及与相转化析出固相的关系进行了讨论。     

Characterization of ceramic PVD thin films on AZ31 magnesium alloys

Ceramic thin films have been widely used to protect the metal substrate as coatings in the past years. In order to improve the poor corrosion resistance of AZ31 magnesium alloy, the study in this paper used the electron beam evaporation method to prepare ceramic PVD films on its surface with TiO₂ and Al₂O₃ as donors, respectively. Atomic force microscopy (AFM), scanning electron microscope (SEM), energy dispersive X-ray spectrometer (EDS), Auger electron spectroscopy (AES) and X-ray diffraction (XRD) were used to investigate the surface morphology, composition and microstructure of the thin films. Both films deposited on AZ31 took on compact top surface morphologies and grew as amorphous structures on substrate. AES test not only showed that films compositions deviated the standard stoichiometric ratios, but also found that element Mg diffused into films and existed as magnesium oxide in the TiO_x film as well as the AlO_x film. In the electrochemical corrosion test, the AlO_x coating on AZ31 exhibited the largest electrochemical impedance in a 3.5% NaCl solution. But it did not show better corrosion resistance than others for the poorer adhesion. Even if its thickness was small, the TiO_x coating on AZ31 exhibited the best corrosion resistance in this study. According to the observation and analysis, the damage of these films on AZ31 in aggressive solutions was mainly due to the existence of pores, microcracks, vacancies and poor adhesion between coating and substrate.     

MgBr2·OEt2 mediated protection of alcohols with hexamethyldisilazane: An efficient catalytic route for the preparation of silyl ethers under solvent-free conditions

Various types of alcohols and phenols were rapidly protected by hexamethyldisilazane in good to excellent yields at room temperature in the presence of catalytic amount of magnesium bromide ethyl etherate under solvent-free conditions. Good to excellent chemoselectivity was demonstrated for competitive protection of primary hydroxyls in the presence of secondary and tertiary alcohols. Highly selective protection of phenols in the presence of aromatic amines was also demonstrated successfully.     

Darstellung und Kristallstruktur von TICu[CuO2]

Investigations on Electronically Conducting Oxide Systems. XVI. Solid Solutions and Conductivity in the System MgTi₂O₅? Ti₃O₅ Solid solution formation is reported for the system Mg_1–xTi_2–x^IVTi_2x^IIIO₅. With increasing x there is at room temperature a transition from the orthorhombic pseudobrookite structure to the monoclinic low-temperature modification of Ti₃O₅. The X-ray diffraction pattern results are supported by DSC measurements, electrical and magnetic investigations. The tendency of Ti? Ti pair formation in the low-temperature Ti₃O₅ structure is accompanied by a drop of the activation energy for electrical conductivity and a decreasing susceptibility at high Ti^III concentrations.     

Preparation of solutions of amidomagnesium chlorides in poly(ethylene oxide) and their characterization by conductivity measurements

Polymer electrolyte systems were prepared for the first time by dissolution of amidomagnesium chlorides in poly(ethylene oxide), (PEO). For the preparation, solutions of (hexamethyldisilylamido)magnesium chloride, (dimethylpyrrolyl)magnesium chloride, (diisopropylamido)magnesium chloride, piperidinomagnesium chloride and morpholinomagnesium chloride were chosen. The composition of these polymer electrolyte systems corresponds to the general formula R₂NMgCl·P(EO)_n·THF. Most work has been done with the system (hexamethyldisilylamido)magnesium chloride in PEO, (Me₃Si)₂NMgCl·P(EO)_n·THF, with n= 3, 4, 5, or 7. The electrolytes have a soft rubber-like consistency. At 30 °C, electrical conductivities of 10⁻⁶–10⁻⁵ S/cm were found. The conductivities were measured in the temperature range 20–60 °C. Within this temperature range a linear dependence of the logarithms of the conductivity on the inverse temperature was found and activation energies for the conducting process of 30–60 kJ/mol were calculated. Using those polymer electrolytes with a high content of the amidomagnesium compound, a reversible magnesium deposition takes place by cathodic reduction at potentials below −1.9 V vs. a Ag/AgCl reference electrode. These polymer electrolytes were found to be stable against oxidation up to about −0.3 V vs. Ag/AgCl. Electronic Publication     

Potentiometric measurements of the first hydrolysis quotient of magnesium(II) to 250°C and 5 molal ionic strength (NaCl)

The first molal hydrolysis quotient, Q_1.1, of Mg²⁺ was measured potentiometrically from 1 to 250°C at ionic strengths of 0.11, 0.31, 1.01, and 5.0 mol-kg^-1 in an aqueous NaCl medium using a hydrogen-electrode, concentration cell. Only hydrolysis of the first four percent of the magnesium in solution could be followed before precipitation of brucite, Mg(OH)₂(cr), occurred. The log Q_1.1 values were fitted as a function of temperature and ionic strength using four adjustable parameters. The resulting constants are compared with the limited existing low temperature data. At infinite dilution and 25°C the following quantities are reported: logK _1.1 = -11.68±0.05, †H_so = 70.1±1.2 kJ-mol^-1, †S^o = 11±4 J-K^-1-mol^-1, and †C _p ^o = 0 J-K^-1-mor^-1. At each ionic strength, including the values extrapolated to infinite dilution, the heat capacity change for the hydrolysis reaction was zero,i.e., logQ _1.1 was found to be a linear function of the reciprocal temperature in Kelvin, at least over the measured range of l-250°C. The hydrolysis constants at infinite dilution were modeled to 550°C and two kbar pressure with a function incorporating solvent density using published results obtained at these extreme conditions.     

Structural and physical properties of Mg3−xZnxSb2 (x=0-1.34)

The Mg_3−xZn_xSb₂ phases with x=0-1.34 were prepared by direct reactions of the elements in tantalum tubes. According to the X-ray single crystal and powder diffraction, the Mg_3−xZn_xSb₂ phases crystallize in the same P3¯m1 space group as the parent Mg₃Sb₂ phase. The Mg_3−xZn_xSb₂ structure is different from the other substituted structures of Mg₃Sb₂, such as (Ca, Sr, Ba) Mg₂Sb₂ or Mg_5.23Sm_0.77Sb₄, in a way that in Mg_3−xZn_xSb₂ the Mg atoms on the tetrahedral sites are replaced, while in the other structures Mg on the octahedral sites is replaced. Thermoelectric performance for the two members of the series, Mg₃Sb₂ and Mg_2.36Zn_0.64Sb₂, was evaluated from low to room temperatures through resistivity, Seebeck coefficient and thermal conductivity measurements. In contrast to Mg₃Sb₂ which is a semiconductor, Mg_2.36Zn_0.64Sb₂ is metallic and exhibits an 18-times larger dimensionless figure-of-merit, ZT, at room temperature. However, thermoelectric performance of Mg_2.36Zn_0.64Sb₂ is still poor and it is mostly due to its large electrical resistivity.     

Access to the structures of fluoromagnesium compounds: synthesis and structural characterization of the β-diketiminato magnesium fluoride [{CH(CMeNAr)2}Mg(μ-F)(THF)]2·toluene

β-Diketiminato magnesium fluoride [{CH(CMeNAr)₂}Mg(μ-F)(THF)]₂·toluene (Ar=2,6-i-Pr₂C₆H₃, 2·toluene) was synthesized. The molecular structure of 2 revealed for the first time, the double fluoro bridge feature between the two magnesium atoms with a typical MgF bond length (average 1.95 Å).     

Novel synthesis of 4-halo-3-hydroxy-2-pyrone: one pot rearrangement-cyclization reaction by magnesium halide

Treatment of acetonide protected 4,5-dihydroxy-2-chloroglycidic ester or its rearrangement product, the acetonide protected 4,5-dihydroxy-3-chloro-2-oxo ester, with magnesium halides gave 4-halo-3-hydroxy-2-pyrone in excellent to reasonable yields in one pot. The mechanism of this novel one pot rearrangement-cyclization reaction is also proposed.     

A comparison between the SBR vulcanizates reinforced by magnesium methacrylate added directly or prepared in situ

The styrene-butadiene rubber (SBR) cured by dicumyl peroxide was reinforced by magnesium methacrylate [Mg(MAA)₂], which was added into SBR directly or prepared in situ in SBR through the neutralization of magnesium oxide (MgO) and methacrylic acid (MAA). The experimental results show that the SBR vulcanizates reinforced by Mg(MAA)₂ prepared in situ have better mechanical properties than those reinforced by Mg(MAA)₂ added directly. The SBR vulcanizates with Mg(MAA)₂ prepared in situ are semi-transparent, but those with Mg(MAA)₂ added directly are opaque. The Fourier transform infrared analysis shows that the polymerization conversion of Mg(MAA)₂ in the SBR vulcanizates with Mg(MAA)₂ prepared in situ is much higher than that in the SBR vulcanizates with Mg(MAA)₂ added directly. The scan probe microscopy photographs show that the particles in the SBR vulcanizates with Mg(MAA)₂ prepared in situ are much finer and disperse more evenly than that in the SBR vulcanizates with Mg(MAA)₂ added directly.