Inviscid,laminar and turbulent opposed flows

This paper attempts to reproduce numerically previous experimental findings with opposed flows and extends their range to quantify the effects of upstream pipes and nozzles with inviscid, laminar and turbulent flows. The choice of conservation equations, boundary conditions, algorithms for their solution, the degree of grid dependence, numerical diffusion and the validity of numerical approximations are justified with supporting calculations where necessary. The results of all calculations on the stagnation plane show maximum strain rates close to the annular exit from the nozzles and pipes for lower separations and it can be expected that corresponding reacting flows will tend to extinguish in this region with the extinction moving towards the axis. With laminar flows, the maximum strain rate increased with Reynolds number and the maximum values were generally greater than with inviscid flows and smaller than with turbulent flows. With large separations, the strain rates varied less and this explains some results with reacting flows where the extinction appeared to begin on the axis. The turbulent‐flow calculations allowed comparison of three common variants of a two‐equation first‐moment closure. They provided reasonable and useful indications of strain rates but none correctly represented the rms of velocity fluctuations on the axis and close to the stagnation plane. As expected, those designed to deal with this problem produced results in better agreement with experiment but were still imperfect. Copyright © 2004 John Wiley & Sons, Ltd.     

Effects of timber skidding on chemical characteristics of herbaceous cover, forest floor and topsoil on skidroad in an oak (Quercus petrea L.) forest

This paper examines the effects of timber harvesting by skidding on some soil properties (sand, silt, clay, pH, organic carbon, bulk density and compaction), herbaceous cover (unit mass) and forest floor (unit weight) properties. Also N (%), P, K, Na, Ca, Mg, Fe, Zn, Cu and Mn (ppm) were determined in all herbaceous cover, forest floor and two soil depth (0–5 cm and 5–10 cm) on skidroad of an oak (Quercus petrea L.) stand in Istanbul Belgrad Forest – Turkey. In this study, obtained results are; the forest floor and the herbaceous cover amount on the skidroad have been found considerably lower than undisturbed area. There were some crucial changes in the characteristics of the soil which has been investigated down to 10 cm depth. Soil bulk density was found quite high in the samples taken from the skidroad subject to compaction compared to the ones on the undisturbed area. Nevertheless, no important difference had been detected between the skidroad and the undisturbed area at both soil depths in terms of organic carbon contents. Moreover, the soil acidity (pH) values showed noteworthy differences in the analysis of soil samples taken from both soil depths on the skidroad and on the undisturbed area. Fe and Cu contents of herbaceous samples on skidroad were significantly higher than undisturbed area. Forest floor on skidroad had significantly higher K content, and significantly lower Zn, Mn and N content compared to undisturbed area. P, Fe, Zn and Mn contents were found significantly lower in 0–5 cm soil depth on skidroad than undisturbed area. In 5–10 cm soil depth, concentrations of N, P, Fe, Zn and Mn were significantly lower, while Mg and Cu contents were significantly higher than undisturbed area. Results indicate that long-term harvest using skidding techniques on these sites had adversely affected soil cation concentrations, physical soil conditions and mass of herbaceous cover and forest floor.     

Pore Modification in Porous Ceramic Membranes With Sol-Gel Process and Determination of Gas Permeability and Selectivity

Summary: The aim of the study was to investigate the variation in total surface area, porosity, pore size, Knudsen and surface diffusion coefficients, gas permeability and selectivity before and after the application of sol-gel process to porous ceramic membrane in order to determine the effect of pore modification. In this study, three different sol-gel process were applied to the ceramic support separately; one was the silica sol-gel process which was applied to increase porosity, others were silica-sol dip coating and silica-sol processing methods which were applied to decrease pore size. As a result of this, total surface area, pore size and porosity of ceramic support and membranes were determined by using BET instrument. In addition to this, Knudsen and surface diffusion coefficients were also calculated. After then, ceramic support and membranes were exposed to gas permeation experiments by using the CO₂ gas with different flow rates. Gas permeability and selectivity of those membranes were measured according to the data obtained. Thus, pore surface area, porosity, pore size and Knudsen diffusion coefficient of membrane treated with silica sol-gel process increased while total surface area was decreasing. Therefore, permeability of ceramic support and membrane treated with silica sol-gel process increased, and selectivity decreased with increasing the gas flow rate. Also, surface area, porosity, pore size, permeability, selectivity, Knudsen and surface diffusion coefficients of membranes treated with silica-sol dip coating and silica-sol processing methods were determined. As a result of this, porosity, pore size, Knudsen and surface diffusion coefficients decreased, total surface area increased in both methods. However, viscous flow and Knudsen flow permeability were detected as a consequence of gas permeability test and Knudsen flow was found to be a dominant transport mechanism in addition to surface diffusive flow owing to the small pore diameter in both methods. It was observed that silica-sol processing method had lower pore diameter and higher surface diffusion coefficient than silica-sol dip coating method.     

Synthesis,Characterization, and AC Conductivity of Polyaniline/Selenium Composites

This study reports structural and thermal properties and temperature-dependent alternating current (AC) conductivity of polyaniline/selenium (PANI/Se) composites in emeraldine salt form prepared by a chemical polymerization method. Fourier transform infrared spectroscopy showed that the doping process significantly affected the N-H bond in PANI chain. The free energy change, which was calculated from the Langmuir adsorption isotherm, showed that Se was electrostatically adsorbed on PANI molecules. From the scanning electron microscopy images it was determined that morphological changes caused by the doping process on PANI surface could affect conductivity. Thermal analysis, which was performed with differential scanning calorimetry, showed that the addition of Se increased the degradation temperature of PANI. Depending on the doping level, significant increase was observed in the AC conductivity of PANI, approximately 11, 13, and 17 times for 300, 350, and 400 K temperatures respectively.     

Novel Nanocomposites of Polypyrrole Doped with Fullerene C60

This paper reports on the structural, thermal, and dielectric properties of polypyrrole/fullerene C₆₀ nanocomposites synthesized by a interfacial polymerization method. Fourier transform infrared (FT-IR) and ultraviolet-visible (UV-vis) analyses clearly indicated the existence of interactions between polypyrrole (PPy) and the fullerene C₆₀ nanoparticles. Thermal analyses indicated that the extrapolated onset degradation temperature (T_deg) of PPy increased with increasing doping level. Scanning electron microscopy (SEM) images showed that the fullerene C₆₀ changed the morphology of PPy. Dielectric analyses showed a temperature dependent dielectric relaxation behavior. The relaxation time of the nanocomposites with high doping levels tended to increase with increasing temperature. This behavior of the polypyrrole/fullerene C₆₀ nanocomposites indicated that they could be used as a high temperature ultrasonic transducer.     

Dielectrophoretic characterization and separation of monocytes and macrophages using 3D carbon‐electrodes

Monocyte heterogeneity and its prevalence are revealed as indicator of several human diseases ranking from cardiovascular diseases to rheumatoid arthritis, chronic kidney diseases, autoimmune multiple sclerosis, and stroke injuries. When monocytes and macrophages are characterized and isolated with preserved genetic, phenotypic and functional properties, they can be used as label‐free biomarkers for precise diagnostics and treatment of various diseases. Here, the dielectrophoretic responses of the monocytes and macrophages were examined. We present 3D carbon‐electrode dielectrophoresis (carbon‐DEP) as a separation tool for U937 monocytes and U937 monocyte‐differentiated macrophages. The carbon‐electrodes advanced the usability and throughput of DEP separation, presented wider electrochemical stability. Using the 3D carbon‐DEP chip, we first identified the selective positive and negative DEP responses and specific crossover frequencies of monocytes and macrophages as their signatures for separation. The crossover frequency of monocytes and macrophages was 17 and 30 kHz, respectively. Next, we separated monocyte and macrophage subpopulations using their specific dielectrophoretic responses. Afterward, we used a fluorescence‐activated cell sorter to confirm our results. Finally, we enriched 70% of monocyte cells from the mixed cell population, in other words, concentration of monocyte cells to macrophage cells was five times increased, using the 30‐kHz, 10‐Vpp electric field and 1 μL/min flow rate.     

Synthesis,characterization, aggregation and thermal properties of a novel polymeric metal-free phthalocyanine and its metal complexes

A novel polymeric metal-free phthalocyanine (M = 2H) and its metal complexes (M = Zn, Cu, Co and Ni) were prepared by the tetramerization reaction of 3,6,9-Tris(p-tolylsulfonyl)-1,11-bis(3,4-dicyanophenoxy)-3,6,9-triazaundecane 5 with the appropriate materials. The electrical conductivities of the metal-free phthalocyanine and the metal complexes, measured in air, were found to be ∼10⁻⁶–10⁻⁵ S m⁻¹. The aggregation property of the zinc complex 7 was investigated with Ni²⁺, Cu²⁺, Co²⁺, Pb²⁺, Cd²⁺ and Ag⁺ cations. Thermal analysis of the polymers were done by differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) at a heating rate of 10 °C min⁻¹ under a nitrogen atmosphere. All the novel compounds were characterized by using elemental analysis, UV–Vis, FT–IR, NMR and MS spectral data and DSC, DTA/TG techniques.