Performance improvement of MEH-PPV:PCBM solar cells using bathocuproine and bathophenanthroline as the buffer layers

In this work, bathocuproine (BCP) and bathophenanthroline (Bphen), commonly used in small-molecule organic solar cells (OSCs), are adopted as the buffer layers to improve the performance of the polymer solar cells (PSCs) based on poly(2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene) (MEH-PPV): [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) bulk heterojunction. By inserting BCP or Bphen between the active layer and the top cathode, all the performance parameters are dramatically improved. The power conversion efficiency is increased by about 70% and 120% with 5-nm BCP and 12-nm Bphen layers, respectively, when compared with that of the devices without any buffer layer. The performance enhancement is attributed to BCP or Bphen (i) increasing the optical field, and hence the absorption in the active layer, (ii) effectively blocking the excitons generated in MEH-PPV from quenching at organic/aluminum (Al) interface due to the large band-gap of BCP or Bphen, which results in a significant reduction in series resistance (Rs), and (iii) preventing damage to the active layer during the metal deposition. Compared with the traditional device using LiF as the buffer layer, the BCP-based devices show a comparable efficiency, while the Bphen-based devices show a much larger efficiency. This is due to the higher electron mobility in Bphen than that in BCP, which facilitates the electron transport and extraction through the buffer layer to the cathode.     

柱壳和锥壳结构自由振动特征的数值计算与校验

为了评估柱壳和锥壳结构自由振动特征数值计算的精度,分析不同边界条件、环肋、纵肋以及流体载荷对自由振动特征的影响,计算并校验了典型壳体结构在空气中、浸没以及浸没并充满水情况下的自由振动特征。结果表明,空气中干模态分析在2 kHz内、单面及双面接触水情况下的流固耦合湿模态分析在500 Hz内的计算精度能够控制在10%以内。壳体流固耦合自由振动分析时可以采用实体单元离散也可以采用壳单元离散的方法,前者精度略高,能够有效保证求解收敛的频带范围更宽,但工作量更大。径长比大于0.2时,浸没于水中的自由振动分析可以转换为内部填充水时的自由振动分析,转换时应保证两者流固耦合湿表面积相等,如半浸水和半充满水,能够有效减小计算量;环肋和流体载荷对壳体自由振动特征的影响明显,环肋使柱壳同阶自振频率增加,流体载荷使柱壳同阶自振频率减小且影响幅度更大,两者均会使得柱壳模态振型呈现错序排列;流固耦合效应对无肋柱壳和环肋柱壳自振频率的影响效果相当;柱壳内外有水相对于单面接触水而言,同阶自振频率进一步减小,模态振型基本不变;流体载荷对环肋锥壳的自振频率和模态振型的影响幅度较对环肋柱壳小。      

Alpha Decay of the Neutron-deficient Isotopes 215,216U

The most neutron-deficient isotopes 215;216U were produced in the complete-fusion reaction 180W(40Ar, 4-5n)215,216U. Evaporation residues recoiled from the target were separated in-flight from the primary beam by the gas-filled recoil separator SHANS and subsequently identified on the basis of correlated -decay chains. Two -decaying states were identified in 216U, one for the ground state and the other for the isomeric state with 8+(h9=2f7=2) configuration. The -decay properties for 215;216U and the systematics of 8+ isomeric state in N =124,126 isotones were investigated.     

聚苯胺与还原石墨烯复合材料的微波吸收性能

采用化学氧化法制备聚苯胺与还原石墨烯复合材料。复合材料的结构、晶型和电磁参数分别通过X射线衍射仪及HP8722ES型矢量网络分析仪进行表征、测试与分析。结果表明,同聚苯胺相比,聚苯胺与还原石墨烯复合材料的介电损耗明显增加。而且在复合材料中,石墨烯的含量越大,材料的微波吸收性能越好,在频率波段（9.5~13.4GHz）反射损耗均小于-10 dB,并在频率为11.2 GHz时达到最大反射损耗-29.69 dB。聚苯胺与还原石墨烯的复合使得材料的载流子迁移率变大,吸波特性得到改善。     

一种新型平板彩色显示器件的制备和光谱分析

以MEH-PPV(聚[2-甲氧基-5-(2′-乙基己氧基-对苯乙烯)])和Alq₃作为发光层, 成功制备出ITO/SiO₂/MEH-PPV/SiO₂/Al结构和ITO/SiO₂/Alq₃ /SiO₂/Al结构的固态阴极射线器件。通过分析SSCL光谱,认为这些高速电子激发有机材料后形成Frenkel激子。当器件两个电极之间加的电压比较低时,有机薄膜层的场强也比较低,这些激子被解离的概率很小,从而产生的是激子发光的长波发射;当器件两个电极之间加的电压比较高时,有机薄膜层的场强很高, 在有机层形成的激子大部分被解离, 解离后的电子直接跃迁至LUMO(lowest unoccupancied molecular orbit),这些电子弛豫后从LUMO能级到HOMO(highest occupancied molecular orbit )能级直接辐射跃迁, 接着重新复合发光,从而产生短波发射。制作的固态阴极射线器件可以实现全色发光, 提高发光效率和加强蓝光发射。作者可以预期所研制出的这种SSCL器件必将引发平板显示领域一场新的革命性变革。     

喷水推进器推力的CFD计算方法研究

简要介绍获取喷水推进器推力的理论、试验及数值计算(CFD)方法,重点研究采用动量流量法和壁面积分法计算喷水推进器推力的CFD方法。采用多块网格技术,用六面体结构化网格和四面体非结构化网格相结合的混合网格离散计算区域,采用稳态多参考系方法求解RANS方程,对喷水推进器进水流道、叶轮、导叶体和喷口所组成的整个流场进行数值计算。计算中采用了k-ε湍流模型和标准壁面函数,对用动量流量法计算推力方法中所需的假想流管分界面和进口面的求取做了分析,将两种方法计算的推力与厂商提供的推力特性曲线进行了对比。结果表明,采用CFD计算和分析方法来研究喷水推进系统推力性能是可行、可信的。     

某调距导管桨系泊工况水力性能和流激直发声预报

采用经验证的计算流体力学方法,对某艏辅推调距导管桨设计螺距和系泊工况螺距的水动力性能进行了有效预报,并对系泊工况装船桨流激噪声进行了分析。系泊工况下,由于导管桨的抽吸作用在导管外壁近壁面区域存在与导管内部流动方向相反的逆向流动,且导管桨尾流场速度梯度分布不均匀、流动紊乱,此时桨叶与导管的推力之比约为1.2∶1。系泊工况船+桨的瞬态流场脉动信息表明,导管桨各部件噪声源强度均表现出从1倍到4倍叶频依次下降的规律,最强幅值集中在桨叶导边和导管内壁;在远场声源级频谱曲线中轴向测点线谱较高峰值位置体现出导管桨进流流场的流动特性。对比分析该艏辅推整体和各部件宽带声源级指向性,可知旋转部件(桨叶、桨榖)对总噪声级的贡献较大,静止部件是径向测点噪声的主要贡献源。     

火焰原子吸收光谱法测定不同产地大蒜中11种金属元素的含量

为进一步利用和开发大蒜资源,采用V（硝酸）＋V（高氯酸）=4＋1常压微沸条件下消化,用火焰原子吸收法测定不同产地大蒜中的金属元素Na、Ca、Mg、Mn、Cu、K、Zn、Fe、Cr、Cd和Pb的含量。研究了不同元素的仪器最佳工作条件,并做了准确度和精密度的考察。结果表明,大蒜中Na、Ca、Mg、Mn、Cu、K、Zn、Fe、Cr、Cd和Ph的含量分别为236．49、1598．21、612.44, 6.27, 15.48, 12 172.41, 126.88, 64.46, 1.67, 1.75, 2.02; 172.84, 1 243.38, 610.05, 5.32, 13.60, 11689.65, 120. 07, 78.91, 1.75, 2. 04, 1.97; 136. 90, 1467.93, 574. 16, 6. 27,16.90, 12 263.45, 146.34, 116.20, 1.82, 2.17, 2.25 μg·g^-1。加标回收率为96．60％～105．80％,相对标准偏差（n=9）为：0．24％～4．81％,测定方法简单易行,方便快捷。     

Improved performance of P3HT：PCBM solar cells by both anode modification and short-wavelength energy utilization using Tb（aca）3phen

The performance of P3HT:PCBM solar cells was improved by anode modification using spin-coated Tb(aca)3phen ultrathin films. The modification of the Tb(aca)3phen ultrathin film between the indium tin oxide(ITO) anode and the PEDOT:PSS layer resulted in a maximum power conversion efficiency(PCE) of 2.99% compared to 2.66% for the reference device, which was due to the increase in the short-circuit current density(Jsc). The PCE improvement could be attributed to the short-wavelength energy utilization and the optimized morphology of the active layers. Tb(aca)3phen with its strong down-conversion luminescence properties is suitable for the P3HT:PCBM blend active layer, and the absorption region of the ternary blend films is extended into the near ultraviolet region. Furthermore, the crystallization and the surface morphology of P3HT:PCBM films were improved with the Tb(aca)3phen ultrathin film. The ultraviolent–visible absorption spectra,atomic force microscope(AFM), and X-ray diffraction(XRD) of the films were investigated. Both anode modification and short-wavelength energy utilization using Tb(aca)3phen in P3HT:PCBM solar cells led to about a 12% PCE increase.     

掺杂二氧化钛纳米管对有机电致发光性能的影响

在聚合物电致发光器件中，通过在不同功能层中掺杂二氧化钛纳米管来改善器件的性能.由于二氧化钛纳米管具有p型传导特性，可以显著增大空穴传输层中载流子的迁移率.由于二氧化钛纳米管在发光层中可以增大发光材料分子的刚性，从而减少无辐射跃迁.当把二氧化钛纳米管掺杂到空穴缓冲层中时，由于其与有机分子的强相互作用，一方面降低了空穴的传导性，同时也减少了界面淬灭发光的缺陷态的产生. 关键词： 二氧化钛纳米管 聚合物电致发光 掺杂