Static bending of granular beam: exact discrete and nonlocal solutions

Meccanica - This study is an attempt towards a better understanding of the length scale effects on the bending response of the granular beams. To this aim, a unidimensional discrete granular chain...     

Electrochemical and chemical synthesis of nanostructure copoly(aniline-o-anisidine-o-toluidine) and study of its electrochemical behavior in organic sulfonic acid media

Terpolymerization of aniline, o-anisidine and o-toluidine was carried out by electrochemical and interfacial chemical polymerization. All homopolymers and terpolymer thin films have been synthesized through electropolymerization at room temperature in aqueous solutions containing 0.5 M of organic sulfonic acid, such as p-toluene sulfonic acid, methane sulfonic acid, sulfosalicylic acid, dodecylbenzene sulfonic acid, and 0.1 M of aniline, o-anisidine and o-toluidine monomers, using cyclic voltammetry method, applying a sequential linear potential scan at a rate of 25 mV s^?1 between ?0.1 and 0.9 V. The electrochemical terpolymerization has been performed at various mole ratios of monomers. Nanoparticles obtained from conjugation of homo- and terpolymer with organic sulfonic acids, were prepared by a chemical oxidation via interfacial chemical polymerization. SEM micrographs, FTIR spectra and conductivity measurements using four-probe method were applied for the characterization of the products. Terpolymer was characterized by higher conductivity than poly-o-toluidine and lesser than polyaniline and poly-o-anisidine. The solubility of terpolymers was dependent on the monomers mole ratio.     

Composite of conducting polyaniline-isobutylated urea formaldehyde: Preparation and characterization

Composite of conductive polyaniline-isobutylated urea formaldehyde have been prepared by chemical oxidative emulsion polymerization of aniline in the presence of isobutylated urea formaldehyde resin (BUFR) in toluene-water solvents at room temperature. The mass loading of polyaniline was controlled by varying the BUFR/aniline charging ratio as well as oxidant (ammonium persulfate)/aniline molar ratio. Some factors capable of affecting the yield and conductivity of composite, such as amount of the oxidant, type of the dispersants (span-80 and span-20), and amount of resin and organic acid (para-toluene sulfonic acid) were investigated. The prepared composites were characterized by FTIR spectroscopy and scanning electron microscopy (SEM).     

Some observations on the solvent extraction and spectrophotometric determination of palladium using 3,4-dihydro-4,4,6-trimethyl-2(1H)-pyrimidine-thione as a selective reagent

A highly selective spectrophotometric method is described for the determination of palladium, using 3,4-dihydro-4,4,6-trimethyl-2(1H)-pyridinethione (DTPT). The intense yellow 1:2 complex is extractable in chloroform from aqueous solution of pH 5.5. The maximum absorption occurs at 420 nm, ε = 3.90 × 10⁴ liter/mol⁻¹ cm⁻¹ and the sensitivity of the determination is 0.023 μg/ml. Palladium can be determined over a range of 0.4–24.6 ppm. CN⁻ interferes in this determination and should be absent. The method is applied to the determination of palladium in hydrogenation catalysts.     

Spectrophotometric determination of trace amounts of selenium with catalytic reduction of bromate by hydrazine in hydrochloric acid media

A method is presented for the determination of selenium, based on the catalytic effect of selenium(IV) on the reduction reaction of BrO(-)(3) by N(2)H(4).2HCl. The decolourization of Methyl Orange by the reaction products was used to monitor the reaction spectrophotometrically at 525 nm. This method is precise, highly sensitive, simple, rapid, widely applicable and selective for the determination of selenium(IV) and total selenium. The variables which affected the reaction rate were fully investigated and the optimum conditions were established. Selenium, as low as 1 ng/ml, can be determined by this method. The relative standard deviation of 20 ng of selenium was 0.94% (N = 10). The method was applied to the determination of Se(IV) in a health-care product.     

Spectrophotometric solvent extraction studies of 2-mercaptopyridine-1-oxide and uranyl ion complex

The complex formed by uranyl ion with 2-mercaptopyridine-1-oxide (thione) is studied by spectrophotometry. At pH 4.5 and 25 degrees the only complex formed is UO(2)(thione)(3)(-). The conditional stability constant of this complex is 2.6 x 10(12). Tributyl phosphate is used for the extraction of the complex from the aqueous phase and the extraction constant is 8.9 x 10(12). The use of the reagent for the separation and determination of uranyl ion is elaborated.     

6-phenyl-2,3-dihydro-assym-triazine-3-thione and 5,6-diphenyl-2,3- dihydro-asym-triazine-3-thione as gravimetric reagents for the determination of thallium and palladium

The analytical use of 6-phenyl-2,3-dihydro-asym-triazine-3-thione (PDTT) and 5,6-diphenyl-2,3-dihydro-asym-triazine-3-thione (DDTT) has been investigated. PDTT proved to be suitable for the determination of thallium(I) in the presence of cyanide whereas DDTT is more selective than PDTT in alkaline tartrate solution and is applied for the selective gravimetric determination of palladium. The method is more sensitive than the dimethylglyoxime method. The only metal ions interfering are Hg(II), Ag and Tl(I).