Direct Visualization of Atomic Structure in Multivariate Metal-Organic Frameworks (MOFs) for Guiding Electrocatalysts Design

The direct utilization of metal–organic frameworks (MOFs) for electrocatalytic oxygen evolution reaction (OER) has attracted increasing interests. Herein, we employ the low-dose integrated differential phase contrast-scanning transmission electron microscopy (iDPC-STEM) technique to visualize the atomic structure of multivariate MOFs (MTV-MOFs) for guiding the structural design of bulk MOFs for efficient OER. The iDPC-STEM images revealed that incorporating Fe³⁺ or 2-aminoterephthalate (ATA) into Ni-BDC (BDC: benzenedicarboxylate) can introduce inhomogeneous lattice strain that weaken the coordination bonds, which can be selectively cleaved via a mild heat treatment to simultaneously generate coordinatively unsaturated metal sites, conductive Ni@C and hierarchical porous structure. Thus, excellent OER activity with current densities of 10 and 100 mA cm⁻² are achieved over the defective MOFs at small overpotentials of 286 mV and 365 mV, respectively, which is superior to the commercial RuO₂ catalyst and most of the bulk MOFs.     

多层CT与DSA对急性冠状动脉综合征患者冠状动脉支架置入术后通畅性及狭窄程度的影响

研究多层CT与DSA对急性冠状动脉综合征患者冠状动脉支架置入术后通畅性及狭窄程度的影响。以我院2017年8月-2018年11月在我院诊断治疗的急性冠脉综合征患者80例作为研究对象,对所有患者进行经皮冠状动脉介入治疗(percutaneous coronary intervention,PCI)手术后,分别进行DSA检查以及64排螺旋CT检查。分析不同检查的冠状动脉狭窄、通畅性之间的差异以及不同检查的一致性。通过对CT检查结果以及DSA检查结果的配对卡方检验,两组患者的检查结果之间的差异不存在统计学意义,两种检查对患者的冠状动脉的狭窄情况诊断一致性较好;两种检查方法对患者的管壁厚度以及管径直径诊断之间的差异不存在统计学意义,两种检验方法对患者的管壁厚度以及管径直径诊断一致性较好。总之,多层CT与DSA对急性冠状动脉综合征患者冠状动脉支架置入术后通畅性及狭窄程度的诊断具有较高的一致性,建议临床推广。     

Structural transition of Ti3SiC2 under high hydrostatic pressure: A first-principles study

We theoretically studied the phase transformation, electronic and elastic properties of Ti₃SiC₂ ceramic by using the pseudopotential plane-wave method within the density functional theory. Our results demonstrate that there exists a structural phase transition from α‐Ti₃SiC₂ to β‐Ti₃SiC₂ under pressure up to 384 GPa, and α‐Ti₃SiC₂ is the most stable phase at zero pressure. The calculated electronic band structure and density of states reveal the metallic behavior for the polymorphs of Ti₃SiC₂. The mechanical stability of α‐Ti₃SiC₂ at zero pressure is confirmed by the elastic constants, and is analyzed in terms of electronic level. By analyzing the ratio between bulk and shear moduli, we conclude that α‐Ti₃SiC₂ is brittle in nature.     

A hierarchical porous carbon membrane from polyacrylonitrile/polyvinylpyrrolidone blending membranes:Preparation,characterization and electrochemical capacitive performance

Novel hierarchical porous carbon membranes were fabricated through a simple carbonization procedure of well-defined blending polymer membrane precursors containing the source of carbon polyacrylonitrile （PAN） and an additive of polyvinylpyrrolidone （PVP）, which was prepared using phase inversion method. The as-fabricated materials were further used as the active electrode materials for supercapacitors. The effects of PVP concentration in the casting solution on structure feature and electrochemical capacitive performance of the as-prepared carbon membranes were also studied in detail. As the electrode material for supercapacitor, a high specific capacitance of 278.0 F/g could be attained at a current of 5 mA/cm2 and about 92.90% capacity retention could be maintained after 2000 charge/discharge cycles in 2 mol/L KOH solution with a PVP concentration of 0.3 wt% in the casting solution. The facile hierarchical pore structure preparation method and the good electrochemical capacitive performance make the prepared carbon membrane particularly promising for use in supercapacitor.     

Thermodynamic properties of liquid Au-Cu-Sn alloys determined from electromotive force measurements

A thermally conductive linear low-density polyethylene (LLDPE) composite with aluminum nitride (AlN) as filler was prepared in a heat press molding. Differential scanning calorimeter results indicated that the AlN filler decreases the degree of crystallinity of LLDPE, and has no obvious influence on the melting temperature of LLDPE. Experimental results demonstrated that the LLDPE composites display a high thermal conductivity of 1.25 W/m K and improved thermal stability at 70 wt% AlN content as compared to pure LLDPE. The dielectric constant and dissipation factor increased with AlN content, however, they still remained at relatively low levels, i.e., <5 in wider frequency range from 10 to 10⁶ Hz. The surface treatment of AlN particles had a beneficial effect on improving the thermal conductivity and dielectric constant, whereas, the dissipation factor was less affected. Additionally, the obtained AlN/LLDPE composites have possessed rather low dielectric constant and high electrical insulation, which is suitable for substrate and packaging materials.     

Silica Sulfuric Acid (SSA)/Polyethylene Glycol (PEG) as a Recyclable System for the Synthesis of Quinoxalines and Pyrazines

An efficient and facile method has been developed for the condensation of 1,2-diamines with α-hydroxyketones in polyethylene glycol (PEG) to quinoxalines and pyrazines with good yields in the presence of silica sulfuric acid (SSA). The important features of the methodology are simple operations, environmentally friendliness, and no requirement for metal catalysts. Additionally, the catalyst system (SSA/PEG) could be recovered easily and reused.     

A class of Sierpinski carpets with overlaps

Based on a scheme by Lau and Ngai, a sufficient and necessary condition for an IFS of contractive similitudes to satisfy the open set condition is given. A class of Sierpinski carpets with parameters (λ₁,λ₂) is then investigated.