Formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber blends: Effects of preparation method,composition, and thermal condition

The effects of preparation method, composition, and thermal condition on formation of β‐iPP in isotactic polypropylene/ethylene–propylene rubber (iPP/EPR) blends were studied using modulated differential scanning calorimeter (MDSC), wide angle X‐ray diffraction (WAXD), and phase contrast microscopy (PCM). It was found that the α‐iPP and β‐iPP can simultaneity form in the melt‐blended samples, whereas only α‐iPP exists in the solution‐blended samples. The results show that the formation of β‐iPP in the melt‐blended samples is related to the crystallization temperature and the β‐iPP generally diminishes and finally vanishes when the crystallization temperature moves far from 125 °C. The phenomena that the lower critical temperature of β‐iPP in iPP/EPR obviously increases to 114 °C and the upper critical temperature decreases to 134 °C indicate the narrowing of temperature interval, facilitating the formation of β‐iPP in iPP/EPR. Furthermore, it was found that the amount of β‐iPP in melt‐blended iPP/EPR samples is dependent on the composition and the maximum amount of β‐iPP formed when the composition of iPP/EPR blends is 85:15 in weight. The results through examining the effect of annealing for iPP/EPR samples at melt state indicate that this annealing may eliminate the susceptibility to β‐crystallization of iPP. However, only α‐iPP can be observed in solution‐blended samples subjected to annealing for different time. The PCM images demonstrate that an obvious phase‐separation happens in both melt‐blended and solution‐blended iPP/EPR samples, implying that compared with the disperse degree of EPR in iPP, the preparation method plays a dominant role in formation of β‐iPP. It is suggested that the origin of formation of β‐iPP results from the thermomechanical history of the EPR component in iPP/EPR. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1704–1712, 2007     

稀土对38CrMoAl钢软氮化层抗冲蚀磨损性能的影响

研究了稀土元素对38CrMoAl钢软氮化层抗冲蚀磨损性能的影响. 结果表明: 与软氮化相比, 稀土软氮化提高了38CrMoAl钢的抗冲蚀磨损性能, 同时提高了软氮化层的硬度以及钢的冲击韧度. 由于软氮化时稀土的渗入, 改善了渗层组织, 从而提高了38CrMoAl钢的抗冲蚀磨损性能和机械性能. 扫描电子显微镜对冲蚀磨损试样表面形貌的观察发现, 普通软氮化层的磨损特征为塑性变形形成的犁沟剥落, 并伴随着萌生横向裂纹, 有大块磨屑剥落; 而稀土软氮化层则为塑性变形形成的犁沟剥落.     

Experimental study of photocatalytic oxidation of formaldehyde and its by-products

Formaldehyde is one of the most harmful pollutants that endanger occupants' health and the way of its effective removal has become a focus in the field of air quality. This paper studies the static photocatalytic removal of formaldehyde experimentally and finds out that carbon monoxide, which is more harmful to occupants' health than the formaldehyde itself, is one of the by-products in the process of photocatalytic oxidation of formaldehyde. The increase of carbon monoxide concentration should be taken into consideration in the photocatalytic application. The photocatalyst surface at room temperature can weakly adsorb CO and CO₂, which can deactivate the photocatalysts.     

套索冠醚毛细管色谱柱的研制

用套索冠醚N,N′-双(2-甲基吡啶)-二氮杂-18-冠-6作为固定相,涂渍在弹性石英毛细管内,测其柱效、惰性、热稳定性、平均极性及选择性等性质.其结构由元素分析、红外光谱、核磁共振及质谱分析的试验数据所证实.试验表明,它具有良好的色谱性能、中等极性,适用于对醇、卤代烃、芳香烃等各类异构体的分离,并用分子结构观点探讨了保留机理.     

Preparation and evaluation of uniform-sized molecularly imprinted polymer beads used for the separation of sulfamethazine

Uniform-sized molecularly imprinted polymer (MIP) beads were prepared using a one-step swelling and polymerization method. The obtained sulfamethazine (SMZ)-imprinted polymer showed high affinity and selectivity toward SMZ and other structurally related sulfonamides in acetonitrile or water-acetonitrile mobile phases, particularly in high aqueous systems. The column performance of the MIPs for SMZ and its analogues could be improved by elevating the column temperature and optimizing the flow rate. The hydrogen-bonding effect plays a significant role in the recognition process of SMZ-imprinted polymer systems in organic media, while the ion-exchange effect, as well as hydrophobic effect, dominates the retention mechanism in aqueous-rich media, in addition to shape recognition.     

Electrocatalytic oxidation of formaldehyde and methanol on Ni(OH)2/Ni electrode

A nickel hydroxide-modified nickel electrode (Ni(OH)₂/Ni) was successfully prepared by the cyclic voltammetry (CV) method and the electrocatalytic properties of the electrode for formaldehyde and methanol oxidation have been investigated respectively. The Ni(OH)₂/Ni electrode exhibits high electrocatalytic activity in the reaction. A new method has been developed for formaldehyde determination at the nickel hydroxide-modified nickel electrode and the experimental parameters were optimized. The oxidation peak current is linearly proportional to the concentration of formaldehyde in the range of 7.0 × 10^?5 to 1.6 × 10^?2 M with a detection limit of 2.0 × 10^?5 M. Recoveries of artificial samples are between 93.3 and 103.5%. The effect of scan rate and methanol concentration on the electrochemical behavior of methanol were investigated respectively.     

压力诱导相变原位构建BiVO4/Bi0.6Y0.4VO4型异质结增强光催化全解水性能

光催化完全分解水制氢是一个在粉末颗粒中实现多个串行物理化学步骤的复杂反应过程.这一过程在理论上具有体系简单、成本低、易操作等特点.然而,单步光激发系统中通常存在严重的光生载流子复合,这极大地制约了光催化的整体效率.利用能带结构不同的半导体合理构建异质结催化剂被认为是解决这一难题的重要途径之一.特别是近年来,S型异质结概念的提出为设计异质结结构以及分析不同半导体之间的载流子迁移问题提供了新的思路.本文以小粒径BiVO₄/Bi_0.6Y_0.4VO₄(BYV)为研究对象,首先利用"共沉淀-晶化"的方法制备了BYV固溶体纳米颗粒,随后利用压力诱导固溶体中四方相钒酸铋结构转变为单斜相,从而构建了BiVO₄/Bi_0.6Y_0.4VO₄复合光催化剂.XRD,Raman,HRTEM,HAADF-EDS的结果表明,经过高压后处理的BYV固溶体表面会出现粒径约为5 nm单斜钒酸铋纳米颗粒,实现了原位构建异质结结构.随后载流子动力学的相关表征以及Au选择性光沉积的结果表明,在光照条件下,所构建异质结中的光生电子主要分布在BYV固溶体上,而在表面形成的单斜相钒酸铋颗粒主要起到了类似"空穴"捕获的作用.这种在异质结中的载流子迁移路径符合S型异质结机理.电化学、稳态荧光光谱以及瞬态荧光光谱的表征结果表明,相比于单一固溶体,在S型异质结这种两步激发系统中所存在的载流子迁移路径能够大幅促进光生载流子分离,从而提高了小粒径BYV的光催化完全分解水性能.综上,构建S型异质结是一种解决小粒径光催化剂中载流子分离能力差的有效途径.同时,压力诱导材料晶型转变实现原位构建异质结的制备方法也为提高光生载流子分离效率提供了新的研究思路与机遇.     

二维/二维S-型Bi3NbO7/g-C3N4异质结光催化剂驱动选择性CO2还原制CH4

人工光合作用可直接将二氧化碳转化为一系列碳氢化合物,实现大气中的碳循环,被视为一种既能解决能源短缺又能减少温室气体,进而改善人类生存环境的新型绿色技术.光催化二氧化碳还原体系需要合适的耦合氧化还原反应,以及对外界光源的有效利用以产生足够电子参与反应,因此构建高催化活性和高选择性的催化体系仍然面临着巨大挑战.此外,二维纳米结构(2D)由于具有比表面积大、离子的迁移路径短以及独特的平层电子转移轨道等特性,被证实有利于光催化还原CO₂过程.其中,Bi₃NbO₇特殊的片层结构和合适的能带位置,使其在光催化还原CO₂反应中表现出良好的催化性能.然而,Bi₃NbO₇的光生载流子易复合及反应中光腐蚀严重等缺陷导致其光利用率较低,限制了其实际应用.因此,构建S-型异质结是提高复合材料光催化活性的一种有前途的策略.S-型异质结不仅能有效地分离光生电子和空穴,而且这一电子转移过程赋予了复合物最大的氧化还原能力.同时,S-型光催化体系不仅拥有同样的强氧化和强还原能力,还可显著抑制副反应的发生及副产物的产生,有利于CO₂还原反应的高选择性进行.本文利用简易的溶剂热法制备了一系列S-型Bi₃NbO₇/g-C₃N₄(BNO/UCN)异质结光催化剂,与其纯组分催化剂相比,表现出优异的光催化还原CO₂活性,g-C₃N₄含量为80wt%的BNO/UCN-3光催化剂催化CO₂生成CH₄产率为37.59μmol·g^-1h^-1,是g-C₃N₄的15倍,CH₄选择性为90%;且循环反应10次后仍保持较高的活性及CH4选择性.光催化活性及选择性的显著增强是由于二维分布的纳米结构和S-型电荷转移路径.在可见光照射下,界面内建电场、带边缘弯曲和库仑相互作用协同促进了复合物相对无用的电子和空穴的复合.因此,剩余的电子和空穴具有较高的还原性和氧化性,使复合材料具有较高的氧化还原能力.自由基捕获实验、电子顺磁共振实验和原位X射线光电子能谱实验结果表明,光催化剂中的电子迁移遵循S-型异质结机理.综上,本文不仅为新型S-型异质结CO₂还原光催化剂的设计和制备提供了新方法,而且为未来解决能源短缺及实现碳中和目标提供一定的实验及理论依据.     

Superhydrophobic surface based on micro/nano structured ZnO nanosheets for high-efficiency anticorrosion

Journal of Solid State Electrochemistry - There are two key factors in the fabrication of superhydrophobic surfaces. One is to have the appropriate micro/nano structure, and the other is to reduce...     

Convergent architecting of multifunction-in-one hydrogels as wound dressings for surgical anti-infections

Surgical procedures are susceptible to the cause of infections, which could induce delayed wound healing, oxidative stress and tissue ischemia. Multifunctional wound dressings (e.g., hydrogels) without the induction of antibiotics is promising for the elimination of surgical site infections and the associated complications. Herein, we report a reductionism approach for the fabrication of bioactive hydrogels to recapitulate antibacterial functions as well as antioxidant, pro-angiogenic and hemostatic properties in surgical infection treatments. The hydrogels composed of naturally derived Cirsium setosum extracts (CE, a traditional medicinal herb) and carboxymethyl chitosan (CS) show their capacity for surgical anti-infections on three different models (i.e., infectious random skin flap model, infectious skin defect model and infectious femur fracture model). Due to the innate bioactivities of CE and CS, CECS hydrogels can also reduce the bleeding loss (85% reduction) on a hemorrhaging liver model and improve the vascularization for skin flap regeneration. Overall, bioactive CECS hydrogels integrated with the ease and scalability of assembly process and biological activities without the addition of antibiotics is promising to act as multifunctional wound dressings for surgical anti-infections.