Efficient synthesis of branched poly(acrylic acid) derivatives via postpolymerization modification

The utility of pentafluorophenyl esters for the selective introduction of functional units and branch points in well-defined poly(acrylic acid) (PAA) derivatives is demonstrated using a combination of controlled radical polymerization and postpolymerization modification. Reversible addition-fragmentation chain transfer enables the synthesis of well-defined copolymers—poly(pentafluorophenyl acrylate-co-tert-butyl acrylate)—with the active ester repeat units serving as attachment points for reaction with primary amines, specifically tris(2-(t-butoxycarbonyl)ethyl)methyl amine (Behera's amine). Deprotection using trifluoroacetic acid removes both the backbone and side chain t-butyl esters to give a series of branched PAA derivatives containing novel tricarboxylic acid side chains that are well suited to complexation and multidentate interactions. Surprisingly, the active ester homopolymer is shown to have the highest reactivity with Behera's amine when compared to copolymers with lower incorporation of pentafluorophenyl esters, suggesting an intriguing interplay of neighboring group effects and steric interactions. The ability to tune the efficiency of postpolymerization modification gives a library of PAA derivatives.     

Ambiguous anti-fouling surfaces: Facile synthesis by light-mediated radical polymerization

In an attempt to create a polymer brush-based platform for the systematic study for anti-biofouling surfaces, the benefits of surface initiated, visible light-mediated radical polymerization are utilized to fabricate well-defined, chemically ambiguously patterned surfaces. A variety of analytical tools are used to illustrate the precise tuning of surface chemistry and thoroughly characterize spatially well-defined, hydrophilic/hydrophobic surfaces composed of poly(ethylene glycol methacrylate) and poly(trifluoroethyl methacrylate) with chemical definition on the micron scale. Advantages of both visible light-mediated photopolymerization and traditional copper-catalyzed atom transfer radical polymerization are combined to achieve both high spatial control and expanded monomer tolerance. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016, 54, 253–262     

Hierarchical comb brush architectures via sequential light‐mediated controlled radical polymerizations

A novel strategy for the synthesis and characterization of branched polymer brushes by sequential light‐mediated controlled radical polymerizations is described. Initially, linear brushes are prepared by surface‐initiated copolymerization of methyl methacrylate and 2‐hydroxyethyl methacrylate (HEMA). In a subsequent step, the HEMA side chains are functionalized with initiating groups for secondary graft polymerization, leading to hierarchical, branched architectures. The increased steric bulk due to the polymer side chains results in a dramatic increase in film thickness when compared to the starting linear brushes. This strategy also allows chemical gradient and complex three‐dimensional structures to be obtained by employing grayscale photomasks in combination with controlled radical polymerization. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2276–2284     

Low‐Temperature,Rapid Copolymerization of Acrylic Acid and Sodium Acrylate in Water

Regulating the aqueous polymerization of acrylic acid (AA) is a major opportunity for future materials design, requiring the development of scalable, industry‐oriented procedures that afford modest molar mass and dispersity control without long reaction times and environmentally demanding conditions. To address these challenges, this report presents the rapid copolymerization of aqueous mixtures of AA and sodium acrylate using an inexpensive and scalable protocol based on alkyl iodides/sodium iodide as mediators in water. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1414–1419     

Flow injection on-line dialysis coupled to high performance liquid chromatography for the determination of some organic acids in wine

A combined system of flow injection on-line dialysis sample pretreatment and high performance liquid chromatographic separation/detection (FID-HPLC) was developed for simultaneous determination of six organic acids (tartaric, malic, lactic, acetic, citric and succinic acids). A sample or mixed standard solution (400 μL) was injected into a donor stream (water) of FID system and was pushed further through a dialysis cell, while an acceptor solution (water) was held in the opposite side of the dialysis membrane. The dialysate containing organic acids in the acceptor solution was then flowed to an injection loop of the HPLC valve, where it was further injected into the HPLC system and analysed under normal HPLC conditions, using a reversed-phase (C₁₈) analytical column and UV detection (210 nm). The order of elution was tartaric, malic, lactic, acetic, citric and succinic acids with the analysis time of 8 min. The FID system could be operated in parallel with HPLC separation, providing sample throughput of 7.5 h⁻¹. Dialysis efficiencies of six organic acids were in range of 4.6-9.5%. Calibration graphs for all the mentioned organic acids were linear over the range of 250-7500 mg L⁻¹. Precisions for all the organic acids were within 5.4%. The proposed system was successfully applied for analysis of some Thai wines. By spiking wine samples with mixed acid standard solutions, the percentage recoveries in range of 84-104 were found. This system has advantages of fast and high degrees of automation for dialysis sample pretreatment, on-line sample separation and dilution, good clean-up for prolongation of life-time of the HPLC column and low consumption of chemicals and materials.     

Simultaneous Preparation of Multiple Polymer Brushes under Ambient Conditions using Microliter Volumes

The fabrication of well‐defined, multifunctional polymer brushes under ambient conditions is described. This facile method uses light‐mediated, metal‐free atom‐transfer radical polymerization (ATRP) to grow polymer brushes with only microliter volumes required. Key to the success of this strategy is the dual action of N‐phenylphenothiazine (PTH) as both an oxygen scavenger and polymerization catalyst. Use of simple glass cover slips results in a high degree of spatial and temporal control and allows for multiple polymer brushes to be grown simultaneously. The preparation of arbitrary 3D patterns and functional/emissive polymer brushes demonstrates the practicality and versatility of this novel strategy.     

Species specific isotope dilution for the accurate and SI traceable determination of arsenobetaine and methylmercury in cuttlefish and prawn

Methods based on species specific isotope dilution were developed for the accurate and SI traceable determination of arsenobetaine (AsBet) and methylmercury (MeHg) in prawn and cuttlefish tissues by LC-MS/MS and SPME GC-ICPMS. Quantitation of AsBet and MeHg were achieved by using a ¹³C-enriched AsBet spike (NRC CRM CBET-1) and an enriched spike of Me¹⁹⁸Hg (NRC CRM EMMS-1), respectively, wherein analyte mass fractions in enriched spikes were determined by reverse isotope dilution using natural abundance AsBet and MeHg primary standards. Purity of these primary standards were characterized by quantitative ¹H-NMR with the use of NIST SRM 350b benzoic acid as a primary calibrator, ensuring the final measurement results traceable to SI. Validation of employed methods of ID LC-MS/MS and ID SPME GC-ICPMS was demonstrated by analysis of several biological CRMs (DORM-4, TORT-3, DOLT-5, BCR-627 and BCR-463) with satisfying results.     

Effects of Sm substitution on ferroelectric domains and conductivity in bismuth ferrite ceramics

The large piezoelectric coefficient and multiferroicity of bismuth ferrite (BFO) make it an attractive candidate for lead-free ferroelectric devices. However, large leakage currents have limited broader applications. Rare-earth substitutions in BFO have been shown to improve ferroelectric and magnetic properties. In this work, we employed piezoresponse and conductive atomic force microscopy to study ferroelectric domains in Bi_1-xSm_xFeO₃ (x = 0–0.150) grown by the co-precipitation method. The combined piezoresponse and conductivity measurements can directly visualize the local ferroelectric domains under different sample bias. At Sm mol% > 7.5, Sm-substitution effectively lowers defect-generated conductivity. At Sm mol% < 7.5, conductivity increases due to conductive domain walls inside sample grains. The surfaces of these conductive samples exhibit a p-type rectifying behavior while the bulk is n-type. Our work details how the local piezoelectric properties and transport behaviors of BFO ceramics change as a function of Sm-substitution.