High-throughput characterization of local conductivity of Nd0.9Ca0.1Ba2Cu3O7−δ thin film by the low-temperature scanning microwave microscope

We developed a scanning microwave microscope (SμM) designed for high-throughput electric-property screening as well as for rapid construction of electronic phase diagrams at low temperatures. As a sensor probe, we used a high-Qλ/4 coaxial cavity resonator to which a thin needle with ball-tip end was attached. The sensor module was mounted on the low-temperature XYZ stage, which allowed us to map out the change of resonance frequency and quality factor due to the local tip-sample interaction at low temperatures. From the measurements of combinatorial thin films, such as Ti_1−xCo_xO_2−δ and Nd_0.9Ca_0.1Ba₂Cu₃O_7−δ (NCBCO), it was demonstrated that this SμM system has enough performance for the high-throughput characterization of sample conductance under variable temperature conditions.     

A new route for the construction of the AB-ring core of Taxol

A new method for the construction of the AB-ring core of Taxol was developed utilizing a new skeletal transformation protocol as a pivotal step. The acid-catalyzed rearrangement of the cyclopentenone-allene photoadduct gave a bridged seven-membered ketone, which was easily transformed, using the intramolecular Suzuki reaction and the oxidative cleavage of the vicinal diol, to the bicyclic diketone.     

Quantitative assessment of solid oxide electrochemical doping

Quantitative analysis of metal cation doping by solid oxide electrochemical doping (SOED) has been performed under galvanostatic doping conditions. A M–β″-Al₂O₃ (M=Ag, Na) microelectrode (contact radius: about 10 μm) was used as cation source to attain a homogeneous solid–solid contact between the β″-Al₂O₃ and doping target. In Ag doping into alkali borate glass, the measured dopant amount closely matched the theoretical value. High Faraday efficiencies of above 90% were obtained. This suggests that the dopant amount can be precisely controlled on a micromole scale by the electric charge during electrolysis. On the other hand, current efficiencies of Na doping into Bi₂Sr₂CaCu₂O_y (BSCCO) ceramics depended on the applied constant current. Efficiencies of above 80% were achieved at a constant current of 10 μA (1.6 A cm⁻²). The relatively low efficiencies were explained by the saturation of BSCCO grain boundaries with Na. By contrast, excess Na was detected on the anodic surface of ceramics at a constant current of 100 μA (16 A cm⁻²). In the present study, we demonstrate that SOED enables micromole-scale control over dopant amount.     

Structure induced by irradiation of femtosecond laser pulse in dyed polymeric materials

We investigated the structures induced by an irradiation of a near‐infrared (NIR) femtosecond laser pulse in dye‐doped polymeric materials {poly(methyl methacrylate) (PMMA), thermoplastic epoxy resin (Epoxy), and a block copolymer of methyl methacrylate and ethyl acrylate‐butyl acrylate [p(MMA/EA‐BA) block copolymer]}. Dyes used were classified into two types—type 1 with absorption at 400 nm and type 2 with no absorption at 400 nm. The 400‐nm wavelength corresponds to the two‐photon absorption region by the irradiated NIR laser pulse at 800 nm. Type 1 dye‐doped PMMA and p(MMA/EA‐BA) block copolymer showed a peculiar dye additive effect for the structures induced by the line irradiation of a NIR femtosecond laser pulse. On the contrary, dye‐doped Epoxy did not exhibit a dye additive effect. The different results among PMMA, p(MMA/EA‐BA) block copolymer, and Epoxy matrix polymers are supposed to be related to the difference of electron‐acceptor properties. The mechanism of this type 1 dye‐additive‐effect phenomenon for PMMA and p(MMA/EA‐BA) block copolymer is discussed on the basis of two‐photon absorption of type 1 dye at 400 nm by the irradiation of a femtosecond laser pulse with 800 nm wavelength and the dissipation of the absorbed energy to the polymer matrix among various transition processes. Dyes with a low‐fluorescence quantum yield favored the formation of thicker grating structures. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2800–2806, 2002     

Investigation of the drying conditions for amidosulfuric acid.

The drying conditions for primary standards of volumetric analysis have a significant effect on the titration results due to changes in the purity, stability and homogeneity. Amidosulfuric acid, a strong acid used as a reference material for volumetric analysis in Japan, was dried in a vacuum desiccator or heated at different temperatures, and then measured by Karl-Fischer titration, thermogravimetry/mass spectroscopy (TG-MS), ion chromatography and coulometric titration. The optimum drying conditions were at 50 degrees C for 24 h with crushing.     

Applicability of headspace solid-phase microextraction to the determination of multi-class pesticides in waters

The applicability of headspace solid-phase microextraction (HS-SPME) to pesticide determination in water samples was demonstrated by evaluating the effects of temperature on the extraction of the pesticides. The evaluations were performed using an automated system with a heating module. The 174 pesticides that are detectable with gas chromatograph were selected objectively and impartially based on their physical properties: vapor pressure and partition coefficient between octanol and water. Of the 174 pesticides, 158 (90% of tested) were extracted with a polyacrylate-coated fiber between 30 and 100 degrees C and were determined with gas chromatograph-mass spectrometry. The extraction-temperature profiles of the 158 extracted pesticides were obtained to evaluate the effects of temperature on the extraction of pesticides. The pesticides were classified into four groups according to the shape of their extraction-temperature profiles. The line of demarcation between extractable pesticides and non-extractable pesticides could be drawn in the physical property diagram (a double logarithmic plot of their vapor pressure and partition coefficient between octanol and water). The plot also revealed relationships between classified extraction features and their physical properties. The new method for multi residue screening in which the analytes were categorized into sub-groups based on extraction temperature was developed. In order to evaluate the quantitivity of the developed method, the 45 pesticides were chosen among the pesticides that are typically monitored in waters. Linear response data for 40 of the 45 was obtained in the concentration range below 5 microg/l with correlation coefficients ranging between 0.979 and 0.999. The other five pesticides had poor responses. Relative standard deviations at the concentration of the lowest standard solution for each calibration curve of the pesticides ranged from 3.6 to 18%. The value of 0.01 microg/l in the limits of detection for 17 pesticides was achieved only under the approximate conditions for screening, not under the individually optimized conditions for each pesticide. Recoveries of tested pesticides in actual matrices were essentially in agreement with those obtained by solid-phase extraction.     

Inhibitory effects of 3-O-acyl-(+)-catechins on Epstein-Barr virus activation

In the course of an exploratory investigation of antitumor-promoting catechins, 3-O-acyl-(+)-catechins of varying carbon lengths from C(4) to C(18) were assessed for inhibitory effects on the activation of the Epstein-Barr virus early antigen. Like 3-O-acyl-(-)-epigallocatechins, the (+)-catechin derivatives showed promising effects with the C-3 acyl chain of C(8)-C(11) carbon atoms.     

Micropore-free surface-activated carbon for the analysis of polychlorinated dibenzo-p-dioxins-dibenzofurans and non-ortho-substituted polychlorinated biphenyls in environmental samples

2,3,7,8-Substituted polychlorinated dibenzo-p-dioxins/polychlorinated dibenzofurans (PCDD/Fs) and non-ortho-substituted polychlorinated biphenyls (PCBs) account for almost all of the total toxic equivalents (TEQ) in environmental samples. Activated carbon columns are used to fractionate the samples for GC-MS analysis or bioassay. Micropore-free surface-activated carbon is highly selective for PCDD/Fs and non-ortho-PCBs and can improve the conventional activated carbon column clean-up. Along with sulfuric acid-coated diatomaceous earth columns, micropore-free surface-activated carbon provides a rapid, robust, and high-throughput sample preparation method for PCDD/Fs and non-ortho-PCBs analysis.     

Determination of dispersive and nondispersive components of the surface free energy of glass fibers

The dispersive component _s ^d of the surface free energy of glass fibers and its interaction energy with alkanes, benzene, 1-nitropropane, ethyleneglycol, glycerol, formamide, and water were quantitatively determined by the tensiometric method within two liquids. The values of nondispersive interaction energy I _SL ^p were found to be a linear function of the square root of the nondispersive component of the surface free energy of liquids. This suggests that the nondispersive interaction energy may be represented by the geometric mean of the nondispersive component of the surface free energy of a solid and a liquid. The slope gave the nondispersive component _s ^p of the surface free energy. The _s ^p values are 33 and 14 mJ/m² for the untreated and aminosilane-treated fibers, respectively, suggesting that organophilic character has developed on the surface after aminosilane treatment. The _s ^p value was almost similar after the treatment, probably because of the polar characteristics of amino groups.     

Synthesis,crystal structure and charge transport characteristics of stable peri-tetracene analogues

peri-Acenes have shown great potential for use as functional materials because of their open-shell singlet biradical character. However, only a limited number of peri-acene derivatives larger than peri-tetracene have been synthesized to date, presumably owing to the low stability of the target compounds in addition to the complicated synthesis scheme. Here, a very simple synthesis route for the tetrabenzo[a,f,j,o]perylene (TBP) structure enables the development of highly stable peri-tetracene analogues. Despite a high degree of singlet biradical character, the compounds with four substituents at the zigzag edge show a remarkable stability in solution under ambient conditions, which is better than that of acene derivatives with a closed-shell electronic configuration. The crystal structures of the TBP derivatives were obtained for the first time; these are valuable to understand the relationship between the structure and biradical character of peri-acenes. The application of peri-acenes in electronic devices should also be investigated. Therefore, the semiconducting properties of the TBP derivative were investigated by fabricating the field-effect transistors.

Highly stable peri-tetracene analogues with a high degree of singlet biradical character were synthesized in a very simple route, and their crystal structures and semiconducting properties were investigated.