Estimation of growth rate in unidirectionally solidified multicrystalline silicon by the growth-induced striation method

Multicrystalline silicon was grown by unidirectional solidification method using the accelerated crucible rotation technique. The application of the accelerated crucible rotation technique in unidirectional solidification method induced growth striations across the axial direction of the grown crystal. This striation pattern was observed from carbon concentration distribution, obtained by using Fourier transform infrared spectroscopy. The generated striation pattern was found to be weak and discontinuous. Some striations were absent, probably due to back melting, caused during each crucible rotation. From the growth striations and applied time period in crucible rotation, the growth rate was estimated by using Fourier transformation analysis.     

Integral Representations,Differentiability Properties and Limits at Infinity for Beppo Levi Functions

The first aim in the present paper is to give an integral representation for Beppo Levi functions on R ⁿ. Our integral representation is an extension of Sobolev's integral representation given for infinitely differentiable functions with compact support. As applications, continuity and differentiability properties of Beppo Levi functions are studied.Our second aim in this paper is to study the existence of limits at infinity for Beppo Levi functions. We also consider the existence of fine-type limits at infinity with respect to Bessel capacities, which yields the radial limit result at infinity.     

Complex impedance spectra of chip inductor using Li–Zn–Cu–Mn ferrite

A multi-layer chip inductor (MCI) was fabricated using polycrystalline Li–Zn–Cu–Mn ferrite and the green-sheet technique, and its complex impedance spectrum was evaluated with the help of numerical calculations. The complex impedance spectra of the MCI component using Ni–Zn–Cu ferrite, which have been widely used for this application, were very sensitive to the residual stress and deviated much from the calculated values; however, it was found that the complex impedance spectrum of the MCI component using Li–Zn–Cu–Mn ferrite is quite well reproduced by calculation, where the complex permittivity and permeability of the polycrystalline ferrite as well as the MCI dimensions, were used. It implied that the magneto-striction effect was negligible in case of MCI using Li–Zn–Cu–Mn ferrite, and that the difference was related to magneto-strictive coefficient of the polycrystalline ferrite. Consequently, utilization of Li–Zn–Cu–Mn ferrite enabled us to easily design the complex impedance of MCI component.     

Bump formation on a glass surface with a transparent coating using femtosecond laser processing

The morphology of a glass surface having a transparent coating processed with focused femtosecond laser pulses is investigated. The transparent coating is formed of poly-methyl methacrylate (PMMA). When the glass was coated with a PMMA film with a thickness of 2.8 μm, bumps were formed over a wide range of axial focus positions. The same laser pulse energy produced cavities when processing bare glass with no coating. The bumps were formed as a result of suppressing material emission from the glass surface by a shielding effect of plasma generated by ablation of the PMMA film and by physical blocking of the PMMA film. A thinner film with a thickness of 0.7 μm produced a reduced shielding effect, forming an exploded bump with a small pit at its center and debris around the periphery. PACS 44.10.+i; 61.80.Ba; 79.20.Ds     

Hydrolysis of acetals in water under hydrothermal conditions

A simple method for the hydrolysis of acetals and ketals was accomplished in neutral water or aqueous media by hydrothermal treatment without using acidic reagents. The deacetalization reaction was effectively accelerated in the presence of calcium chloride. Because no acidic catalysts were employed, neutralization of the reaction mixture was not necessary after the reaction. This sequence was successfully applied to the hydrolysis of chitosan, a biodegradable polyaminosaccharide.     

Stable marker-particle method for the Voronoi diagram in a flow field

The Voronoi diagram in a flow field is a tessellation of water surface into regions according to the nearest island in the sense of a “boat-sail distance”, which is a mathematical model of the shortest time for a boat to move from one point to another against the flow of water. The computation of the diagram is not easy, because the equi-distance curves have singularities. To overcome the difficulty, this paper derives a new system of equations that describes the motion of a particle along the shortest path starting at a given point on the boundary of an island, and thus gives a new variant of the marker-particle method. In the proposed method, each particle can be traced independently, and hence the computation can be done stably even though the equi-distance curves have singular points.     

Design of a widely tunable laser with a chirped ladder filter

We theoretically investigated a digitally tunable laser with a chirped ladder filter and a ring resonator to obtain a wide wavelength tuning range covering the whole C- or L- band. The clear relation between the tuning range and laser structure, especially the ladder filter, is described analytically. The introduction of a chirped structure into a ladder filter is effective in achieving both wide tunability and a stable lasing mode. A numerical simulation based on multimode rate equations shows that a tuning range of over 40 nm and a mode suppression ratio over 40 dB can be achieved by introducing a chirped ladder filter.     

A procedure for measuring the flexibility of single wood-pulp fibres

A way of determining the flexibility of wood-pulp fibres is developed, which involves i) a precise measurement of the topology of single-fibres by using a confocal laser scanning microscope and ii) the measurement of the elastic modulus of the fibres by using a single-fibre fatigue cell. Reported in this paper are the initial results of tests carried out on black spruce fibres, which have been subjected to three different levels of mechanical refining energy, namely ∼1100, 2300, and 3500 kWh/t. It is found that the fibre flexibility rises significantly between the first and second energy levels, but it does not change to the same degree between the second and third ones. The described procedure of measuring the flexibility of fibres may be used to establish the appropriate refiner energy necessary for the production of a specific grade of paper. Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 42, No. 1, pp. 115–128, January–February, 2006.