Excellent UV-absorbing cotton fabric with high durability and hydrophobicity based on surface-initiated ATRP of polymerizable organic UV-absorber

Cellulose - Ultraviolet (UV) protective cotton fabric is a convenient and reliable way to protect human body from sunlight. Herein, a polymerizable UV-absorber,...     

Microwave absorption properties of composite powders with low density

The composites of barium ferrite coated on hollow ceramic microspheres were prepared using sol-gel technique. The crystal structure, morphology and microwave absorption properties of composite powders with different weight ratio of microspheres were studied with XRD, EDS, FESEM and vector network analyzer. The results show that the microwave absorption properties of composite powders are greatly improved. The maximum microwave loss of composite powders reaches 31 dB with an amount of 50 wt.% microspheres, and its density is only about 1.80 g/cm³. The effect of hollow ceramic microspheres on the microwave absorption property is also discussed.     

Preparation and microwave absorption properties of electroless Co-Ni-P coated strontium ferrite powder

A new type of Co-Ni-P coated strontium ferrite nanocomposite was prepared with electroless plating enhanced by ultrasonic wave at room temperature. The plating process was studied carefully. The morphology, crystal structure and microwave absorption properties of the Co-Ni-P coated powder were studied with field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), energy dispersive analysis of X-rays (EDX) and vector network analyzer. The results show that the strontium ferrite powder was successfully coated with Co-Ni-P alloy and possesses excellent microwave absorption properties. The maximum microwave loss of the composite powder reaches −44.12 dB. The bandwidth with the loss above −10 dB exceeds 13.8 GHz.     

可用于激光核聚变的闪烁中子探测器

在当前激光核聚变实验中,中子集中在短时间内出现、且产额低。为适应这种特点,要求探测器的效率高,分辨时间短。利用闪烁中子探测器探测激光核聚变所产生的中子,能测定中子产额,记录中子能量,而且探测效率高,分辨时间短。缺点是易受γ射线、X射线的干扰。     

FCC硫转移剂MgAlCuFe复合氧化物的结构与性能:金属盐前体的影响

分别以硝酸盐、盐酸盐和硫酸盐为金属盐前体,采用共沉淀法合成了MgAlCuFe类水滑石前驱体,经过700℃焙烧6h后,制得三种新型FCC硫转移剂.运用X射线衍射、热重、氮气吸附和红外光谱对这三种硫转移剂的结构和性能进行了表征,并采用改装的WRP-3热重天平评价了其氧化吸硫和还原脱硫的性能.结果表明,三种金属盐均可得到结构规整的类水滑石前驱体,经过焙烧后得到复合氧化物MgAlCuFe.与采用盐酸盐和硫酸盐作前体相比,由硝酸盐制得的硫转移剂具有较大的比表面积,其饱和吸附硫容和氧化吸硫速率均较高,6min可达到1.54g/g的饱和吸附能力,同时具有较强的还原脱硫能力.     

CuZnAl水滑石衍生催化剂上甲醇水蒸气重整制氢Ⅲ.合成水滑石用金属盐的影响

采用共沉淀法,用不同金属盐为Cu源和Zn源合成了一系列CuZnAl水滑石,以此为前体经600℃焙烧后制得相应催化剂.用硝酸盐和醋酸盐合成的水滑石结晶度高,其衍生催化剂比表面积大、Cu的分散性好且易于还原;而用硫酸盐和盐酸盐合成的水滑石结晶度差,其衍生催化剂比表面积小、Cu的分散性差且不易还原.反应评价结果显示,用硝酸盐和醋酸盐制得的催化剂活性高、反应稳定性好;而用硫酸盐和盐酸盐制得的催化剂由于低的Cu表面积以及S和Cl的毒化作用而几乎无催化活性.在醋酸盐制备的催化剂上,产物干气中CO的浓度明显较低,在250℃和WHSV=3.28 h-1的条件下约为0.03%~0.04%,仅为硝酸盐所制催化剂上CO浓度的1/5;在210℃和WHSV=0.5 h-1的条件下,该催化剂上甲醇几乎完全转化,同时CO浓度降至约0.005%.N2O滴定、CO2程序升温脱附和程序升温还原结果显示,用醋酸盐和硝酸盐制备的催化剂具有极相近的Cu表面积和表面碱性,但前者CuO的还原峰温较后者低近70℃,归因于ZnO与CuO间的强相互作用,这是催化剂具有良好选择性的可能原因.     

Direct synthesis, characterization of Cu-SBA-15 and its high catalytic activity in hydroxylation of phenol by H2O2

Transition metal copper substituted mesoporous silica (Cu-SBA-15) was synthesized using triblock copolymers surfactant as template agent under acidic condition. The result Cu-SBA-15 was characterized with XRD, ICP-AES, FT-IR and N₂ adsorption–desorption measurements, which prove that Cu(II) was mainly incorporated into the framework of Cu-SBA-15. Its catalytic activity was studied for phenol hydroxylation using H₂O₂ (30%). The substituting element (Cu²⁺) is incorporated into the framework position forming a new type of active site which raises the phenol conversion to 62.4% and the diphenol (the mixture of catechol (CAT) and hydroquinone (HQ)) selectivity to 97%. The Cu-SBA-15 has very high selectivity for catechol (about 71% selectivity), which is completely different from that of the microporous titanium silicalite zeolites (47.1% phenol conversion and about 50% selectivity to CAT under same reaction conditions). The results obtained indicate that the selective oxidation of phenol with H₂O₂ by a radical substitution mechanism.     

影响SAPO－11分子筛焙烧前后晶胞空间群变化的因素

 从合成参数出发，详细考察了不同因素对SAPO－11分子筛焙烧前后晶胞空间群变化的影响．发现成胶方式、成胶温度、模板剂组成、晶化温度、晶化时间及分子筛产物组成均是影响分子筛晶胞空间群变化的因素．MAS－NMR分析结果表明，分子筛的微观结构决定了分子筛晶胞空间群的变化，Si（4Si）区增加，分子筛保持为Icm2空间群的趋势增强．     

离子液体体系中1－丁烯二聚反应的研究

 研究了在强酸性AlCl3／Et2AlCl／［BMIM］Cl型离子液体体系中过渡金属化合物对1－丁烯二聚反应的催化作用．结果表明，［BMIM］Cl对强酸性AlCl3／Et2AlCl催化剂催化1－丁烯高聚反应有明显的阻聚作用，并显著提高了1－丁烯二聚的选择性．在过渡金属化合物中，含镍化合物对1－丁烯二聚反应有最好的催化效果．在最佳反应条件下，1－丁烯的转化率可达95．1％，二聚产物C8烯的选择性为85．8％．同时，对1－丁烯二聚反应的机理进行了初步探讨．     

MMM分子筛的制备与表征

 以碱溶液处理ZSM－5分子筛，得到了含微孔及介孔的MFI结构分子筛（简称MMM），并采用XRD，XRF，SEM，XPS和低温氮吸附等技术对分子筛进行了表征．结果表明，通过改变处理碱的浓度可以得到具有不同物化性能的MMM分子筛，其化学组成、介孔及微孔的大小和多少，及分子筛晶体上n（Al）／n（Si）均随碱浓度的变化而变化，随着碱浓度的增加，分子筛部分微孔结构遭到破坏，介孔的数量增加，孔径增大，n（Al）／n（Si）增大．碱处理脱硅的过程包括脱除晶粒间的无定形物质，脱除分子筛表面的硅及脱除分子筛体相硅等步骤，硅脱除以后形成了介孔．